SLI related fixes:

- Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230)
- Fix ELS FDISC failing with local reject / invalid RPI. (126350)
- Fix reset port when reset is needed during fw_dump (125807)
- Fix unbounded firmware revision string from port cause panic (126560)
- Fix driver behavior when receiving an ADISC (126654)
- Fix driver not returning when bad ndlp found in abts error event
  handling (126209)
- Add more driver logs in area of SLI4 port error attention and reset
  recovery (126813, 124466)
- Fix failure in handling large CQ/EQ identifiers in an IOV
  environment (126856)
- Fix for driver using duplicate RPIs after lancer port reset (126723)
- Clear vport->fc_myDID in lpfc_els_issue_fdisc to guarentee a
  zero SID (126779, 126897)
- Fix for SLI4 Port delivery for BLS ABORT ACC (126289)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

BSG and User interface fixes:

- Fix driver processing an els command using 16Gb FC Adapter (126345)
- Change SLI4 FC port internal loopback to inner internal (126409)
- Fix bug with driver dump command type 4 using 16Gb FC Adapter (126406)
- Create character device to take a reference on the driver (126082)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

IO_XFER_ERROR_BREAK and IO_XFER_OPEN_RETRY_TIMEOUT are deficient of the
required actions as outlined in the programming manual for the pm8001. Due to
the overlapping code requirements of these recovery responses, we found it
necessary to bundle them together into one patch.

When a break is received during the command phase (ssp_completion), this is a
result of a timeout or interruption on the bus. Logic suggests that we should
retry the command.

When a break is received during the data-phase (ssp_event), the task must be
aborted on the target or it will retain a data-phase lock turning the target
reticent to all future media commands yet will successfully respond to TUR,
INQUIRY and ABORT leading eventually to target failure through several
abort-cycle loops.

The open retry interval is exceedingly short resulting in occasional target
drop-off during expander resets or when targets push-back during bad-block
remapping. Increased effective timeout from 130ms to 1.5 seconds for each try
so as to trigger after the administrative inquiry/tur timeout in the scsi
subsystem to keep error-recovery harmonics to a minimum.

When an open retry timeout event is received, the action required by the
targets is to issue an abort for the outstanding command then logic suggests
we retry the command as this state is usually an indication of a credit block
or busy condition on the target.

We hijacked the pm8001_handle_event work queue handler so that it will handle
task as an argument instead of device for the workers in support of the
deferred handling outlined above.

Moderate to Heavy bad-path testing on a 2.6.32 vintage kernel, compile-testing
on scsi-misc-2.6 kernel ...
Signed-off-by: NMark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Jack noticed I dropped a patch fragment associated with a flags automatic
variable in mpi_set_phys_g3_with_ssc (ooops) and that the pre-emptive locking
that piggy-backed this patch was not in-fact necessary because of underlying
atomic accesses to the hardware. Here is the updated patch fixing these two
issues.

The pm8001 driver is missing the FUNC_GET_EVENTS handler in the phy control
function. Since the pm8001_bar4_shift function was not designed to be called
at runtime, added locking surrounding the adjustment for all accesses.
Signed-off-by: NMark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

pm8001_phy_control PHY_FUNC_HARD_RESET locks up on second try via
smp_phy_control because response HW_EVENT_PHY_START_STATUS fails to complete
previous command. The PM8001F_RUN_TIME flag is not treated as a bit, but a
state in all readers, yet once we are operational or in the run time state,
the flags use a bit-set operation.
Signed-off-by: NMark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This implements basic power management for SCSI tapes.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Acked-by: NKai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch (as1520) fixes a bug in the SCSI layer's power management
implementation.

LUN scanning can be carried out asynchronously in do_scan_async(), and
sd uses an asynchronous thread for the time-consuming parts of disk
probing in sd_probe_async().  Currently nothing coordinates these
async threads with system sleep transitions; they can and do attempt
to continue scanning/probing SCSI devices even after the host adapter
has been suspended.  As one might expect, the outcome is not ideal.

This is what the "prepare" stage of system suspend was created for.
After the prepare callback has been called for a host, target, or
device, drivers are not allowed to register any children underneath
them.  Currently the SCSI prepare callback is not implemented; this
patch rectifies that omission.

For SCSI hosts, the prepare routine calls scsi_complete_async_scans()
to wait until async scanning is finished.  It might be slightly more
efficient to wait only until the host in question has been scanned,
but there's currently no way to do that.  Besides, during a sleep
transition we will ultimately have to wait until all the host scanning
has finished anyway.

For SCSI devices, the prepare routine calls async_synchronize_full()
to wait until sd probing is finished.  The routine does nothing for
SCSI targets, because asynchronous target scanning is done only as
part of host scanning.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In do_scan_async(), calling scsi_autopm_put_host(shost) may reference
freed shost, and cause Posison overwitten warning.
Yes, this case can happen, for example, an USB is disconnected just
when do_scan_async() thread starts to run, then scsi_host_put() called
in scsi_finish_async_scan() will lead to shost be freed(because the
refcount of shost->shost_gendev decreases to 1 after USB disconnects),
at this point, if references shost again, system will show following
warning msg.

To make scsi_autopm_put_host(shost) always reference a valid shost,
put it just before scsi_host_put() in function
scsi_finish_async_scan().

[  299.281565] =============================================================================
[  299.281634] BUG kmalloc-4096 (Tainted: G          I ): Poison overwritten
[  299.281682] -----------------------------------------------------------------------------
[  299.281684]
[  299.281752] INFO: 0xffff880056c305d0-0xffff880056c305d0. First byte
0x6a instead of 0x6b
[  299.281816] INFO: Allocated in scsi_host_alloc+0x4a/0x490 age=1688
cpu=1 pid=2004
[  299.281870] 	__slab_alloc+0x617/0x6c1
[  299.281901] 	__kmalloc+0x28c/0x2e0
[  299.281931] 	scsi_host_alloc+0x4a/0x490
[  299.281966] 	usb_stor_probe1+0x5b/0xc40 [usb_storage]
[  299.282010] 	storage_probe+0xa4/0xe0 [usb_storage]
[  299.282062] 	usb_probe_interface+0x172/0x330 [usbcore]
[  299.282105] 	driver_probe_device+0x257/0x3b0
[  299.282138] 	__driver_attach+0x103/0x110
[  299.282171] 	bus_for_each_dev+0x8e/0xe0
[  299.282201] 	driver_attach+0x26/0x30
[  299.282230] 	bus_add_driver+0x1c4/0x430
[  299.282260] 	driver_register+0xb6/0x230
[  299.282298] 	usb_register_driver+0xe5/0x270 [usbcore]
[  299.282337] 	0xffffffffa04ab03d
[  299.282364] 	do_one_initcall+0x47/0x230
[  299.282396] 	sys_init_module+0xa0f/0x1fe0
[  299.282429] INFO: Freed in scsi_host_dev_release+0x18a/0x1d0 age=85
cpu=0 pid=2008
[  299.282482] 	__slab_free+0x3c/0x2a1
[  299.282510] 	kfree+0x296/0x310
[  299.282536] 	scsi_host_dev_release+0x18a/0x1d0
[  299.282574] 	device_release+0x74/0x100
[  299.282606] 	kobject_release+0xc7/0x2a0
[  299.282637] 	kobject_put+0x54/0xa0
[  299.282668] 	put_device+0x27/0x40
[  299.282694] 	scsi_host_put+0x1d/0x30
[  299.282723] 	do_scan_async+0x1fc/0x2b0
[  299.282753] 	kthread+0xdf/0xf0
[  299.282782] 	kernel_thread_helper+0x4/0x10
[  299.282817] INFO: Slab 0xffffea00015b0c00 objects=7 used=7 fp=0x
      (null) flags=0x100000000004080
[  299.282882] INFO: Object 0xffff880056c30000 @offset=0 fp=0x          (null)
[  299.282884]
...
Signed-off-by: NHuajun Li <huajun.li.lee@gmail.com>
Cc: stable@kernel.org
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

With IOs running and PegHalt testing the system reboots when memory reset is
performed during device initialization.
Signed-off-by: NShyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Complete mailbox command timedout to avoid initialization failures during next reset cycle.

Complete the mailbox command timed out before initiating another abort cycle
to recover so that mailbox commands issued during next reset cycle don't fail
due to pending mailbox access timeout.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Remove the check for a NULL fcport so that the host reset will run
unconditionally to unwedge any commands before the device is offlined and to
prevent a quick runthrough of the SCSI error handling.
Signed-off-by: NMichael Christie <mchristi@redhat.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

ISP2200 adapters only have 24 mailbox registers so read only that many.
Reported-by: NOlatunji Ruwase <oor@cs.cmu.edu>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This can cause instability in mailbox command state machine handling.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Not clearing the options flags in mbx1 could lead the firmware
into interpreting old data in mbx1 through mbx8.  This could
lead to inadvertent DMA read/write operations to stale memory.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Many locations within the driver would use an inconsistent set of
checks to determine ISP-reset state.  Consolidate the checks into
this inline-helper.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

NULL orom ptr passed in for verification which caused page fault.
We will set a default version when we don't have orom struct.
Reported-by: NDan Melnic <dan@seamicro.com>
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In some scenarios, an EEH error can take a long time to be detected, since the
driver issues an MMIO read only after a device reset command times out and we
try to reset the adapter. This patch adds some code in ipr_cancel_op() to read
a hardware register so we detect the error earlier in case the op is being
aborted because of a timeout caused by a frozen adapter slot.

Another problem in such scenarios is that in __ipr_eh_host_reset() we change the
dump state flag from WAIT_FOR_DUMP to GET_DUMP, and the flag is later changed
from GET_DUMP to READ_DUMP in ipr_reset_restore_cfg_space(). However, if when
__ipr_eh_host_reset() is called by the SCSI error handling the function
ipr_reset_restore_cfg_space() has already been called by the PCI EEH code, we
end up with the flag in an inconsistent state. This patch also prevents this
problem.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If ioc->pci_error_recovery is set, goto out in mpt2sas_base_hard_reset_handler()
leads to unlock unheld ioc->reset_in_progress_mutex.

The patch fixes the issue by jumping afer mutex_unlock() call.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Says Jens:

 "Time to push off some of the pending items.  I really wanted to wait
  until we had the regression nailed, but alas it's not quite there yet.
  But I'm very confident that it's "just" a missing expire on exit, so
  fix from Tejun should be fairly trivial.  I'm headed out for a week on
  the slopes.

  - Killing the barrier part of mtip32xx.  It doesn't really support
    barriers, and it doesn't need them (writes are fully ordered).

  - A few fixes from Dan Carpenter, preventing overflows of integer
    multiplication.

  - A fixup for loop, fixing a previous commit that didn't quite solve
    the partial read problem from Dave Young.

  - A bio integer overflow fix from Kent Overstreet.

  - Improvement/fix of the door "keep locked" part of the cdrom shared
    code from Paolo Benzini.

  - A few cfq fixes from Shaohua Li.

  - A fix for bsg sysfs warning when removing a file it did not create
    from Stanislaw Gruszka.

  - Two fixes for floppy from Vivek, preventing a crash.

  - A few block core fixes from Tejun.  One killing the over-optimized
    ioc exit path, cleaning that up nicely.  Two others fixing an oops
    on elevator switch, due to calling into the scheduler merge check
    code without holding the queue lock."

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix lockdep warning on io_context release put_io_context()
  relay: prevent integer overflow in relay_open()
  loop: zero fill bio instead of return -EIO for partial read
  bio: don't overflow in bio_get_nr_vecs()
  floppy: Fix a crash during rmmod
  floppy: Cleanup disk->queue before caling put_disk() if add_disk() was never called
  cdrom: move shared static to cdrom_device_info
  bsg: fix sysfs link remove warning
  block: don't call elevator callbacks for plug merges
  block: separate out blk_rq_merge_ok() and blk_try_merge() from elevator functions
  mtip32xx: removed the irrelevant argument of mtip_hw_submit_io() and the unused member of struct driver_data
  block: strip out locking optimization in put_io_context()
  cdrom: use copy_to_user() without the underscores
  block: fix ioc locking warning
  block: fix NULL icq_cache reference
  block,cfq: change code order

11a3122f "block: strip out locking optimization in put_io_context()"
removed ioc_lock depth lockdep annoation along with locking
optimization; however, while recursing from put_io_context() is no
longer possible, ioc_release_fn() may still end up putting the last
reference of another ioc through elevator, which wlil grab ioc->lock
triggering spurious (as the ioc is always different one) A-A deadlock
warning.

As this can only happen one time from ioc_release_fn(), using non-zero
subclass from ioc_release_fn() is enough.  Use subclass 1.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Quoth David:

1) GRO MAC header comparisons were ethernet specific, breaking other
   link types.  This required a multi-faceted fix to cure the originally
   noted case (Infiniband), because IPoIB was lying about it's actual
   hard header length.  Thanks to Eric Dumazet, Roland Dreier, and
   others.

2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
   From Anisse Astier.

3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.

4) ipv4 TCP reset generation needs to respect any network interface
   binding from the socket, otherwise route lookups might give a
   different result than all the other segments received.  From Shawn
   Lu.

5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
   Graf.

6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.

7) Revert skge PCI mapping changes that are causing crashes for some
   folks, from Stephen Hemminger.

8) IPV4 route lookups fill in the wildcarded fields of the given flow
   lookup key passed in, which is fine most of the time as this is
   exactly what the caller's want.  However there are a few cases that
   want to retain the original flow key values afterwards, so handle
   those cases properly.  Fix from Julian Anastasov.

9) IGB/IXGBE VF lookup bug fixes from Greg Rose.

10) Properly null terminate filename passed to ethtool flash device
    method, from Ben Hutchings.

11) S3 resume fix in via-velocity from David Lv.

12) Fix double SKB free during xmit failure in CAIF, from Dmitry
    Tarnyagin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
  net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
  ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
  netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
  netprio_cgroup: don't allocate prio table when a device is registered
  netprio_cgroup: fix an off-by-one bug
  bna: fix error handling of bnad_get_flash_partition_by_offset()
  isdn: type bug in isdn_net_header()
  net: Make qdisc_skb_cb upper size bound explicit.
  ixgbe: ethtool: stats user buffer overrun
  ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
  ixgbe: do not update real num queues when netdev is going away
  ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
  ixgbe: Fix case of Tx Hang in PF with 32 VFs
  ixgbe: fix vf lookup
  igb: fix vf lookup
  e1000: add dropped DMA receive enable back in for WoL
  gro: more generic L2 header check
  IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
  zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
  net: enable TC35815 for MIPS again
  ...

Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.

Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.

This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: NLi Wei <lw@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the netprio_cgroup module is not loaded, net_prio_subsys_id
is -1, and so sock_update_prioidx() accesses cgroup_subsys array
with negative index subsys[-1].

Make the code resembles cls_cgroup code, which is bug free.
Origionally-authored-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So we delay the allocation till the priority is set through cgroup,
and this makes skb_update_priority() faster when it's not set.

This also eliminates an off-by-one bug similar with the one fixed
in the previous patch.
Origionally-authored-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

# mount -t cgroup xxx /mnt
  # mkdir /mnt/tmp
  # cat /mnt/tmp/net_prio.ifpriomap
  lo 0
  eth0 0
  virbr0 0
  # echo 'lo 999' > /mnt/tmp/net_prio.ifpriomap
  # cat /mnt/tmp/net_prio.ifpriomap
  lo 999
  eth0 0
  virbr0 4101267344

We got weired output, because we exceeded the boundary of the array.
We may even crash the kernel..
Origionally-authored-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
  drm/i915: no lvds quirk for AOpen MP45
  drm/i915: Force explicit bpp selection for intel_dp_link_required
  drm/radeon: do not continue after error from r600_ib_test
  drivers/gpu/drm/drm_ioc32.c: initialize all fields
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
  drm/i915:: Disable FBC on SandyBridge

fix 1 mysterious divide error
fix 3 NULL dereference bugs in writeback tracing, on SD card removal w/o umount

* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: fix dereferencing NULL bdi->dev on trace_writeback_queue
  lib: proportion: lower PROP_MAX_SHIFT to 32 on 64-bit kernel
  writeback: fix NULL bdi->dev in trace writeback_single_inode
  backing-dev: fix wakeup timer races with bdi_unregister()

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix double start/stop in x86_pmu_start()
  perf evsel: Fix an issue where perf report fails to show the proper percentage
  perf tools: Fix prefix matching for kernel maps
  perf tools: Fix perf stack to non executable on x86_64
  perf: Remove deprecated WARN_ON_ONCE()

Couple of regressions, couple of zero-day bugs, a minor enhancement.
Nothing really major.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (f75375s) Let f75375_update_device treat pwmX as a measured value
  hwmon: (f75375s) Fix bit shifting in f75375_write16
  hwmon: (f75375s) Fix reading of wrong register when initializing the F75387
  hwmon: (f75375s) Fix automatic pwm mode setting for F75373 & F75375
  hwmon: (w83627ehf) Remove duplicate code

Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux into drm-fixes

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
  drm/i915: no lvds quirk for AOpen MP45
  drm/i915: Force explicit bpp selection for intel_dp_link_required
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
  drm/i915:: Disable FBC on SandyBridge

"subbuf_size" and "n_subbufs" come from the user and they need to be
capped to prevent an integer overflow.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Serial/TTY fixes for the 3.3-rc3 tree

Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
  tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
  tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
  m32r: relocate drivers back out of 8250 dir
  tty: fix a build failure on sparc
  serial: samsung: Add support for EXYNOS5250
  serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
  drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer

Staging tree patches for 3.3-rc3

Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.

Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
  staging: pohmelfs: remove drivers/staging/pohmelfs
  staging: android/ram_console: Don't build on arches w/o ioremap
  staging: r8712u: Use asynchronous firmware loading
  staging: usbip: fix to prevent potentially using uninitialized spinlock
  staging: r8712u: Fix problem when CONFIG_R8712_AP is set
  staging: tidspbridge: fix incorrect free to drv_datap
  staging: tidspbridge: fix bridge_open memory leaks
  staging: android: lowmemorykiller: Don't wait more than one second for a process to die
  MAINTAINERS: staging: iio: add iio information
  staging: zcache: fix serialization bug in zv stats
  staging: fix go7007-usb license
  Staging: android: binder: Fix crashes when sharing a binder file between processes
  Staging: android: Remove pmem driver
  Staging: asus_oled: fix NULL-ptr crash on unloading
  Staging: asus_oled: fix image processing
  Staging: android: binder: Don't call dump_stack in binder_vma_open
  staging: r8712u: Add new Sitecom UsB ID
  zcache: Set SWIZ_BITS to 8 to reduce tmem bucket lock contention.
  zcache: fix deadlock condition
  staging: drm/omap: fix locking issue
  ...

Driver core fixes for the 3.3-rc3 tree.

A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver-core: cpu: fix kobject warning when hotplugging a cpu
  ACPI: remove duplicated lines of merging problems with acpi_processor_add
  docbook: fix fatal errors in device-drivers docbook and add DMA Management section
  drivers/base/memory.c: fix memory_dev_init() long delay
  driver core: cpu: remove kernel warning when removing a cpu

Minor char-misc fixes for 3.3-rc3

Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
  cs5535-mfgpt: don't call __init function from __devinit
  vmw_balloon: fix for a -Wuninitialized warning
  drivers: misc: Remove MISC_DEVICES config option
  c2port: fix build error for duramar2150 due to missing header.