Adds support for interrupt coalescing feature to reduce interrupt events.
Provides a mechanism of adjusting coalescing count and timeout tick by sysfs
at runtime, so that tradeoff of latency and CPU load can be made depending
on different applications.
Signed-off-by: NQiang Liu <qiang.liu@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds in Hibernation related callbacks. Also we don't really need to
free DMA channel on suspend.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

According to the HT6560H datasheet, the recovery timing field is 4-bit wide,
with a value of 0 meaning 16 cycles. Correct obvious thinko in the recovery
field mask.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the IDE-mode SATA DeviceIDs for the Intel Lynx Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the AHCI-mode SATA DeviceIDs for the Intel Lynx Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

num_sifr could go negative since acpi_pcc_get_sqty() returns -EINVAL
on error.  Then it could bypass the sanity check (num_sifr > 255).
The subsequent call to kzalloc() would allocate a small buffer, leading
to a memory corruption.
Signed-off-by: NXi Wang <xi.wang@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

We have several reports which says acer-wmi is loaded on ideapads
and register rfkill for wifi which can not be unblocked.

Since ideapad-laptop also register rfkill for wifi and it works
reliably, it will be fine acer-wmi is not going to register rfkill
for wifi once VPC2004 is found.

Also put IBM0068/LEN0068 in the list. Though thinkpad_acpi has no
wifi rfkill capability, there are reports which says acer-wmi also
block wireless on Thinkpad E520/E420.
Signed-off-by: NIke Panhc <ike.pan@canonical.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

This patch adds support for some of the devices within a wide variety
of Fujitsu Tablet Computers, both convertibles and slates. Primarily
it allows for the automatic detection of the tablet/notebook mode for
convertible tablet pc's, and orientation for docked slates. It also
adds support for the application panel buttons usually found next to
the tablet screen, and docking station detection for slates.
Signed-off-by: NRobert Gerlach <khnz@gmx.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

An rfkill driver based on the fsaa1655g and fsam7440 drivers for
Fujitsu-Siemens Amilo A1655 and M7440 models found at:

http://sourceforge.net/projects/fsaa1655g/
http://sourceforge.net/projects/fsam7440/

This adds DMI matching, replaces the procfs files with rfkill devices,
and uses the proper functions to write to the i8042 safely.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

The runtime PM of sh-sci devices is enabled when sci_probe() returns,
so the pm_runtime_put_sync() executed by driver_probe_device()
attempts to suspend the device.  Then, in some situations, a
diagnostic message is printed to the console by one of the runtime
suspend routines handling the sh-sci device, which causes synchronous
runtime resume to be started from the device's own runtime suspend
callback.  This causes rpm_resume() to be run eventually, which sees
the RPM_SUSPENDING status set by rpm_suspend() and waits for it to
change.  However, the device's runtime PM status cannot change at
that point, because the routine that has set it waits for the
rpm_suspend() to return.  A deadlock occurs as a result.

To avoid that make sci_init_single() increment the device's
runtime PM usage counter, so that it cannot be suspended by
driver_probe_device().  That counter has to be decremented
eventually, so make sci_startup() do that before starting to
actually use the device and make sci_shutdown() increment it
again before returning to balance the incrementation carried out by
sci_startup().
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Cc: Olaf Hering <olaf@aepfle.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is called from enable_iommus(), which in turn is used
from amd_iommu_resume().

Cc: stable@vger.kernel.org
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

All pre-SI chips are limited to 165 Mhz for single link.
Code in question will be re-enabled when SI support is added.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=44755
https://bugzilla.kernel.org/show_bug.cgi?id=42887Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Mesa may set it to 1, causing all primitives to be killed.

v2: also update the r7xx code
Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

|kernel BUG at kernel/rtmutex.c:724!
|[<c029599c>] (rt_spin_lock_slowlock+0x108/0x2bc) from [<c01c2330>] (defer_bh+0x1c/0xb4)
|[<c01c2330>] (defer_bh+0x1c/0xb4) from [<c01c3afc>] (rx_complete+0x14c/0x194)
|[<c01c3afc>] (rx_complete+0x14c/0x194) from [<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0)
|[<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0) from [<c01e1ff4>] (musb_giveback+0x34/0x40)
|[<c01e1ff4>] (musb_giveback+0x34/0x40) from [<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0)
|[<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0) from [<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c)
|[<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c) from [<c01e2ed0>] (musb_urb_dequeue+0xec/0x108)
|[<c01e2ed0>] (musb_urb_dequeue+0xec/0x108) from [<c01cbb90>] (unlink1+0xbc/0xcc)
|[<c01cbb90>] (unlink1+0xbc/0xcc) from [<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8)
|[<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8) from [<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58)
|[<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58) from [<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c)
|[<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c) from [<c01c2d68>] (usbnet_stop+0x100/0x15c)
|[<c01c2d68>] (usbnet_stop+0x100/0x15c) from [<c020f718>] (__dev_close_many+0x94/0xc8)

defer_bh() takes the lock which is hold during unlink_urbs(). The safe
walk suggest that the skb will be removed from the list and this is done
by defer_bh() so it seems to be okay to drop the lock here.

Cc: stable@kernel.org
Reported-by: NAníbal Almeida Pinto <anibal.pinto@efacec.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The actual FW command is called in procedure "handle_resize".
Code incorrectly invoked the FW command again (in good flow), in
the modify_cq wrapper function.

Fix by skipping second FW invocation unconditionally for resize.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ATL1C_WORK_EVENT_RESET is zero so the original code here is a nop.  The
intent was to set the zero bit.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 239c562c (ehea: Add 64bit statistics) added a regression,
since we no longer report multicast & rx_errors fields, taken from
port->stats structure. These fields are updated in ehea_update_stats()
every second.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now we won't touch ASPM state if ASPM is disabled, except in the case
where we find a device that appears to be too old to reliably support ASPM.
Right now we'll clear it in that case, which is almost certainly the wrong
thing to do. The easiest way around this is just to disable the blacklisting
when ASPM is disabled.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

As per datasheet, the voltage output is defined as
from SEL[6:0] = 3 to 64 (dec)
Vout= (SEL[6:0] × 12.5 mV + 562.5 mV)

The list_voltage returns the vout as
    600mV +  selector * 12.5mV

and so equivalent VSEL is selector + 3.
Adding 3 on selector when configuring VSEL register for
VDDCTRL output.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix dm-raid flush support.

Both md and dm have support for flush, but the dm-raid target
forgot to set the flag to indicate that flushes should be
passed on.  (Important for data integrity e.g. with writeback cache
enabled.)
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The 'rebuild' parameter is used to rebuild individual devices in an
array (e.g. resynchronize a RAID1 device or recalculate a parity device
in higher RAID).  The MD_CHANGE_DEVS flag must be set when this
parameter is given in order to write out the superblocks and make the
change take immediate effect.  The code that handles new devices in
super_load already sets MD_CHANGE_DEVS and 'FirstUse'.  (The 'FirstUse'
flag was being set as a special case for rebuilds in
super_init_validation.)

Add a condition for rebuilds in super_load to take care of both flags
without the special case in 'super_init_validation'.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Correct the number of mapped sectors shown on a thin device's
status line by decrementing td->mapped_blocks in __remove() each time
a block is removed.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

If dm_sm_disk_create() fails the superblock must be unlocked.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The __open_device() error paths in __create_thin() and __create_snap()
incorrectly call __close_device() even if td was not initialized by
__open_device().  Remove this.

Also document __open_device() return values, remove a redundant
td->changed = 1 in __create_thin(), and insert an additional
safeguard against creating an already-existing device.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The following BUG is hit on the first read that is submitted to a dm
flakey test device while the device is "down" if the corrupt_bio_byte
feature wasn't requested when the device's table was loaded.

Example DM table that will hit this BUG:
0 2097152 flakey 8:0 2048 0 30

This bug was introduced by commit a3998799
(dm flakey: add corrupt_bio_byte feature) in v3.1-rc1.

BUG: unable to handle kernel paging request at ffff8801cfce3fff
IP: [<ffffffffa008c233>] corrupt_bio_data+0x6e/0xae [dm_flakey]
PGD 1606063 PUD 0
Oops: 0002 [#1] SMP
...
Call Trace:
 <IRQ>
 [<ffffffffa008c2b5>] flakey_end_io+0x42/0x48 [dm_flakey]
 [<ffffffffa00dca98>] clone_endio+0x54/0xb6 [dm_mod]
 [<ffffffff81130587>] bio_endio+0x2d/0x2f
 [<ffffffff811c819a>] req_bio_endio+0x96/0x9f
 [<ffffffff811c94b9>] blk_update_request+0x1dc/0x3a9
 [<ffffffff812f5ee2>] ? rcu_read_unlock+0x21/0x23
 [<ffffffff811c96a6>] blk_update_bidi_request+0x20/0x6e
 [<ffffffff811c9713>] blk_end_bidi_request+0x1f/0x5d
 [<ffffffff811c978d>] blk_end_request+0x10/0x12
 [<ffffffff8128f450>] scsi_io_completion+0x1e5/0x4b1
 [<ffffffff812882a9>] scsi_finish_command+0xec/0xf5
 [<ffffffff8128f830>] scsi_softirq_done+0xff/0x108
 [<ffffffff811ce284>] blk_done_softirq+0x84/0x98
 [<ffffffff81048d19>] __do_softirq+0xe3/0x1d5
 [<ffffffff8138f83f>] ? _raw_spin_lock+0x62/0x69
 [<ffffffff810997cf>] ? handle_irq_event+0x4c/0x61
 [<ffffffff8139833c>] call_softirq+0x1c/0x30
 [<ffffffff81003b37>] do_softirq+0x4b/0xa3
 [<ffffffff81048a39>] irq_exit+0x53/0xca
 [<ffffffff81398acd>] do_IRQ+0x9d/0xb4
 [<ffffffff81390333>] common_interrupt+0x73/0x73
...
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.1+
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch fixes a crash by recognising discards in dm_io.

Currently dm_mirror can send REQ_DISCARD bios if running over a
discard-enabled device and without support in dm_io the system
crashes badly.

BUG: unable to handle kernel paging request at 00800000
IP:  __bio_add_page.part.17+0xf5/0x1e0
...
 bio_add_page+0x56/0x70
 dispatch_io+0x1cf/0x240 [dm_mod]
 ? km_get_page+0x50/0x50 [dm_mod]
 ? vm_next_page+0x20/0x20 [dm_mod]
 ? mirror_flush+0x130/0x130 [dm_mirror]
 dm_io+0xdc/0x2b0 [dm_mod]
...

Introduced in 2.6.38-rc1 by commit 5fc2ffea
(dm raid1: support discard).
Signed-off-by: NMilan Broz <mbroz@redhat.com>
Cc: stable@kernel.org
Acked-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

If 'argc' is zero we jump to the 'out:' label, but this leaks the
(unused) memory that 'dm_split_args()' allocated for 'argv' if the
string being split consisted entirely of whitespace.  Jump to the
'out_argv:' label instead to free up that memory.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Cc: stable@kernel.org
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Also update IDT datasheet locations.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: NJean Delvare <khali@linux-fr.org>

A global delay parameter has the side effect of being overwritten with 0 if a
single ZL2004 or ZL6105 is instantiated. If other chips supported by the same
driver are in the system, this will result in access errors for those chips.

To solve the problem, keep a per-instance copy of the delay parameter, and do
not change the original parameter.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.1+
Acked-by: NJean Delvare <khali@linux-fr.org>

There are up to three POUT alarm attributes, not two, since cap_alarm was added.
Reported-by: NMichele Petracca <mi.petracca@gmail.com>
Cc: stable@vger.kernel.org # 3.0+ [3.0 will need backport]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

These are fully compatible with Jedec JC 42.4 as far as I can see.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

We've been getting occasional oops running a 32-bit kernel on a certain
system in our RHEL test hw. It appears that we fail to get sufficent ioremap
space for the framebuffer, and this leads to an oops.

This patch should fix the oops and leave a message in the logs we can
check for.

A future fix would probably to resize the console to a size that we can
ioremap.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The out of order execution of semaphore commands on
pre cayman asics doesn't work correctly and can
cause deadlocks, so turn it off for now.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The message count field uses three bits of storage, not two.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Acked-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Default MTU for CAIF HSI was wrongly set to 15 * 4092 bytes.
The patch sets default MTU size to 4096.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes a bug introduced by commit fe9a2603, where the priority bits
in the schedule queue field were masked out.
Signed-off-by: NAmir Vadai <amirv@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With runtime PM, if the ethernet cable is disconnected, the device is
transitioned to D3 state to conserve energy. If the system is shutdown
in this state, any register accesses in rtl_shutdown are dropped on
the floor. As the device was programmed by .runtime_suspend() to wake
on link changes, it is thus brought back up as soon as the link recovers.

Resuming every suspended device through the driver core would slow things
down and it is not clear how many devices really need it now.

Original report and D0 transition patch by Sameer Nanda. Patch has been
changed to comply with advices by Rafael J. Wysocki and the PM folks.
Reported-by: NSameer Nanda <snanda@chromium.org>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>