Pull USB fixes from Greg KH:
 "Here are some small USB fixes, PHY driver fixes (they ended up in this
  tree for lack of somewhere else to put them), and some new USB device
  ids"

* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
  phy: core: Fix error path in phy_create()
  drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
  phy: omap-usb2: fix devm_ioremap_resource error detection code
  phy: sun4i: depend on RESET_CONTROLLER
  USB: serial: ftdi_sio: Add Infineon Triboard
  USB: ftdi_sio: Add extra PID.
  usb: option: Add ID for Telewell TW-LTE 4G v2
  USB: cp210x: add support for Corsair usb dongle

Pull tty/serial fixes from Greg KH:
 "Here are some small serial fixes that resolve some reported problems
  that started in 3.15 with some serial drivers.

  And there's a new dt binding for a serial driver, which was all that
  was needed for the renesas serial driver"

* tag 'tty-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: sh-sci: Add device tree support for r8a7{778,740,3a4} and sh73a0
  serial: imx: Fix build breakage
  serial: arc_uart: Use uart_circ_empty() for open-coded comparison
  serial: Test for no tx data on tx restart

Pull char/misc driver fixes from Greg KH:
 "Here are two hyperv driver fixes, and one i8k driver fix for 3.16"

* tag 'char-misc-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  i8k: Fix non-SMP operation
  Drivers: hv: util: Fix a bug in the KVP code
  Drivers: hv: vmbus: Fix a bug in the channel callback dispatch code

Pull IIO fixes from Greg KH:
 "Here are some IIO driver fixes for 3.16-rc5.  Nothing major, just
  resolves some minor issues that have been reported"

* tag 'staging-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: ti_am335x_adc: Fix: Use same step id at FIFOs both ends
  iio:tcs3472: Check for buffer enabled and locking
  iio: hid-sensor-prox: Fix return values
  iio: hid-sensor-gyro-3d: Fix return values
  iio: hid-sensor-als: Fix return values
  iio: hid-sensor-magn-3d: Fix return values
  iio: hid-sensor-accel-3d: Fix return values
  iio: hid-sensor-press: Fix return values

Dell kernel driver dell-smo8800 provides same freefall interface as hp_accel so
program hpfall.c works also on Dell laptops. So rename it to freefall.c.

Dell driver does not provide hp::hddprotect led so make sure that freefall.c
works also if hp::hddprotect does not exist in sysfs.

Additionally write info to syslog.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Cc: Sonal Santan <sonal.santan@gmail.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixed spelling typo in various template files
within Documentation/Docbook.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixed spelling typo found in DocBook/mtdnand.tmpl.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Object-like macros are different than function-like macros:
https://gcc.gnu.org/onlinedocs/cpp/Object-like-Macros.html
https://gcc.gnu.org/onlinedocs/cpp/Function-like-Macros.html

They are not parsed correctly, generating invalid intermediate
files (xmls) for cases like:
    #define BIT_MASK    (0xFF << BIT_SHIFT)
where "OxFF <<" is considered to be parameter type.

When parsing, we can differentiate beween these two types of macros by
checking whether there is at least one whitespace b/w "#define" and
first opening parenthesis.
Signed-off-by: NHoria Geanta <horia.geanta@freescale.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The paragraph on mcelog currently describes kernel v2.6.31. In that
kernel the mce code (for i386, that is) was in transition. Ever since
v2.6.32 the situation is much simpler (eg, mcelog is now needed to
process events on almost all x86 machines, i386 and x86-64). Since this
"document is designed to provide a list of the minimum levels of
software necessary to run the 3.0 kernels" let's just describe that
situation.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.

This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.

Balance out the pm_runtime_enable() call in .remove() as well.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.

Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.

A simplified version of the semantic match that finds this problem is as
follows:

// <smpl>
@@
expression e,e1;
statement S;
@@

*e = devm_ioremap_resource(...);
if (!e1) S

// </smpl>
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver depend on the reset framework in a mandatory way. Make sure
reset_control_get is defined by adding this dependency in Kconfig
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds support for Infineon TriBoard TC1798 [1]. Only interface 1
is used as serial line (see [2], Figure 8-6).

[1] http://www.infineon.com/cms/de/product/microcontroller/development-tools-software-and-kits/tricore-tm-development-tools-software-and-kits/starterkits-and-evaluation-boards/starter-kit-tc1798/channel.html?channel=db3a304333b8a7ca0133cfa3d73e4268
[2] http://www.infineon.com/dgdl/TriBoardManual-TC1798-V10.pdf?folderId=db3a304412b407950112b409ae7c0343&fileId=db3a304333b8a7ca0133cfae99fe426aSigned-off-by: NMichal Sojka <sojkam1@fel.cvut.cz>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Simply document new compat strings.
There appears to be no need for a driver updates.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix breakage introduced by
commit c557d392,
'serial: Test for no tx data on tx restart'.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull x86 fixes from Peter Anvin:
 "A couple of further build fixes for the VDSO code.

  This is turning into a bit of a headache, and Andy has already come up
  with a more ultimate cleanup, but most likely that is 3.17 material"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86-32, vdso: Fix vDSO build error due to missing align_vdso_addr()
  x86-64, vdso: Fix vDSO build breakage due to empty .rela.dyn

Pull nfsd bugfix from Bruce Fields:
 "Another xdr encoding regression that may cause incorrect encoding on
  failures of certain readdirs"

* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
  nfsd: Fix bad reserving space for encoding rdattr_error

Pull arm64 fixes from Catalin Marinas:
 "ARM64 implementation of TASK_SIZE_OF and exporting two functions to
  modules"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: implement TASK_SIZE_OF
  arm64: export __cpu_{clear,copy}_user_page functions

Pull device mapper fixes from Mike Snitzer:

 - Fix DM multipath IO hang regression from 3.15 due to logic bug in
   multipath_busy.  This impacted cable-pull testing and also the
   ability to boot with IPR SCSI on a POWER8 box.

 - Fix possible deadlock with deferred device removal by using a new
   dedicated workqueue rather than using the system workqueue.

 - Fix NULL pointer crash due to race condition in dm-io's wake up code
   for sync_io by using a completion.

 - Update dm-crypt and dm-zero author name following legal name change;
   this is important to Jana so I didn't see any reason to hold it back.

* tag 'dm-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm mpath: fix IO hang due to logic bug in multipath_busy
  dm io: fix a race condition in the wake up code for sync_io
  dm crypt, dm zero: update author name following legal name change
  dm: allocate a special workqueue for deferred device removal

Pull powerpc fixes from Ben Herrenschmidt:
 "Here are a few more powerpc fixes for 3.16

  There's a small series of 3 patches that fix saving/restoring MMUCR2
  when using KVM without which perf goes completely bonkers in the host
  system.  Another perf fix from Anton that's been rotting away in
  patchwork due to my poor eyesight, a couple of compile fixes, a little
  addition to the WSP removal by Michael (removing a bit more dead
  stuff) and a fix for an embarassing regression with our soft irq
  masking"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/perf: Never program book3s PMCs with values >= 0x80000000
  powerpc: Disable RELOCATABLE for COMPILE_TEST with PPC64
  powerpc/perf: Clear MMCR2 when enabling PMU
  powerpc/perf: Add PPMU_ARCH_207S define
  powerpc/kvm: Remove redundant save of SIER AND MMCR2
  powerpc/powernv: Check for IRQHAPPENED before sleeping
  powerpc: Clean up MMU_FTRS_A2 and MMU_FTR_TYPE_3E
  powerpc/cell: Fix compilation with CONFIG_COREDUMP=n

We are seeing a lot of PMU warnings on POWER8:

    Can't find PMC that caused IRQ

Looking closer, the active PMC is 0 at this point and we took a PMU
exception on the transition from negative to 0. Some versions of POWER8
have an issue where they edge detect and not level detect PMC overflows.

A number of places program the PMC with (0x80000000 - period_left),
where period_left can be negative. We can either fix all of these or
just ensure that period_left is always >= 1.

This patch takes the second option.

Cc: <stable@vger.kernel.org>
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Pull drm fixes from Dave Airlie:
 "Nothing too scary, we have one outstanding i915 regression but Daniel
  has promised the fix as soon as he's finished testing it a bit.

  Fixes for the main x86 drivers:
   - radeon: dpm fixes, displayport regression fix
   - i915: quirks for backlight regression, edp reboot fix, valleyview
     black screen fixes
   - nouveau: display port regression fixes, fix for memory reclocking"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/dpm: Reenabling SS on Cayman
  drm/radeon: fix typo in ci_stop_dpm()
  drm/radeon: fix typo in golden register setup on evergreen
  drm/radeon: only print meaningful VM faults
  drm/radeon/dp: return -EIO for flags not zero case
  drm/i915/vlv: T12 eDP panel timing enforcement during reboot
  drm/i915: Only unbind vgacon, not other console drivers
  drm/i915: Don't clobber the GTT when it's within stolen memory
  drm/i915/vlv: Update the DSI ULPS entry/exit sequence
  drm/i915/vlv: DPI FIFO empty check is not needed
  drm/i915: Toshiba CB35 has a controllable backlight
  drm/i915: Acer C720 and C720P have controllable backlights
  drm/i915: quirk asserts controllable backlight presence, overriding VBT
  drm/nouveau/ram: fix test for gpio presence
  drm/nouveau/dp: workaround broken display
  drm/nouveau/dp: fix required link bandwidth calculations
  drm/nouveau/kms: restore fbcon after display has been resumed
  drm/nv50-/kms: pass a non-zero value for head to sor dpms methods
  drm/nouveau/fb: Prevent inlining of ramfuc_reg
  drm/gk104/ram: bash mpll bit 31 on

powerpc:allmodconfig has been failing for some time with the following
error.

arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:1312: Error: attempt to move .org backwards
make[1]: *** [arch/powerpc/kernel/head_64.o] Error 1

A number of attempts to fix the problem by moving around code have been
unsuccessful and resulted in failed builds for some configurations and
the discovery of toolchain bugs.

Fix the problem by disabling RELOCATABLE for COMPILE_TEST builds instead.
While this is less than perfect, it avoids substantial code changes
which would otherwise be necessary just to make COMPILE_TEST builds
happy and might have undesired side effects.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On POWER8 when switching to a KVM guest we set bits in MMCR2 to freeze
the PMU counters. Aside from on boot they are then never reset,
resulting in stuck perf counters for any user in the guest or host.

We now set MMCR2 to 0 whenever enabling the PMU, which provides a sane
state for perf to use the PMU counters under either the guest or the
host.

This was manifesting as a bug with ppc64_cpu --frequency:

    $ sudo ppc64_cpu --frequency
    WARNING: couldn't run on cpu 0
    WARNING: couldn't run on cpu 8
      ...
    WARNING: couldn't run on cpu 144
    WARNING: couldn't run on cpu 152
    min:    18446744073.710 GHz (cpu -1)
    max:    0.000 GHz (cpu -1)
    avg:    0.000 GHz

The command uses a perf counter to measure CPU cycles over a fixed
amount of time, in order to approximate the frequency of the machine.
The counters were returning zero once a guest was started, regardless of
weather it was still running or had been shut down.

By dumping the value of MMCR2, it was observed that once a guest is
running MMCR2 is set to 1s - which stops counters from running:

    $ sudo sh -c 'echo p > /proc/sysrq-trigger'
    CPU: 0 PMU registers, ppmu = POWER8 n_counters = 6
    PMC1:  5b635e38 PMC2: 00000000 PMC3: 00000000 PMC4: 00000000
    PMC5:  1bf5a646 PMC6: 5793d378 PMC7: deadbeef PMC8: deadbeef
    MMCR0: 0000000080000000 MMCR1: 000000001e000000 MMCRA: 0000040000000000
    MMCR2: fffffffffffffc00 EBBHR: 0000000000000000
    EBBRR: 0000000000000000 BESCR: 0000000000000000
    SIAR:  00000000000a51cc SDAR:  c00000000fc40000 SIER:  0000000001000000

This is done unconditionally in book3s_hv_interrupts.S upon entering the
guest, and the original value is only save/restored if the host has
indicated it was using the PMU. This is okay, however the user of the
PMU needs to ensure that it is in a defined state when it starts using
it.

Fixes: e05b9b9e ("powerpc/perf: Power8 PMU support")
Cc: stable@vger.kernel.org
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Instead of separate bits for every POWER8 PMU feature, have a single one
for v2.07 of the architecture.

This saves us adding a MMCR2 define for a future patch.

Cc: stable@vger.kernel.org
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

These two registers are already saved in the block above. Aside from
being unnecessary, by the time we get down to the second save location
r8 no longer contains MMCR2, so we are clobbering the saved value with
PMC5.

MMCR2 primarily consists of counter freeze bits. So restoring the value
of PMC5 into MMCR2 will most likely have the effect of freezing
counters.

Fixes: 72cde5a8 ("KVM: PPC: Book3S HV: Save/restore host PMU registers that are new in POWER8")
Cc: stable@vger.kernel.org
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NPaul Mackerras <paulus@samba.org>
Reviewed-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 8d6f7c5a: "powerpc/powernv: Make it possible to skip the IRQHAPPENED
check in power7_nap()" added code that prevents cpus from checking for
pending interrupts just before entering sleep state, which is wrong. These
interrupts are delivered during the soft irq disabled state of the cpu.

A cpu cannot enter any idle state with pending interrupts because they will
never be serviced until the next time the cpu is woken up by some other
interrupt. Its only then that the pending interrupts are replayed. This can result
in device timeouts or warnings about this cpu being stuck.

This patch fixes ths issue by ensuring that cpus check for pending interrupts
just before entering any idle state as long as they are not in the path of split
core operations.
Signed-off-by: NPreeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In fb5a5157 "powerpc: Remove platforms/wsp and associated pieces",
we removed the last user of MMU_FTRS_A2. So remove it.

MMU_FTRS_A2 was the last user of MMU_FTR_TYPE_3E, so remove it also.
This leaves some unreachable code in mmu_context_nohash.c, so remove
that also.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 046d662f "coredump: make core dump functionality optional"
made the coredump optional, but didn't update the spufs code that
depends on it. That leads to build errors such as:

  arch/powerpc/platforms/built-in.o: In function `.spufs_arch_write_note':
  coredump.c:(.text+0x22cd4): undefined reference to `.dump_emit'
  coredump.c:(.text+0x22cf4): undefined reference to `.dump_emit'
  coredump.c:(.text+0x22d0c): undefined reference to `.dump_align'
  coredump.c:(.text+0x22d48): undefined reference to `.dump_emit'
  coredump.c:(.text+0x22e7c): undefined reference to `.dump_skip'

Fix it by adding some ifdefs in the cell code.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Pull kbuild fixes from Michal Marek:
 "Three more fixes for the relative build dir feature:

   - Shut up make -s again
   - Fix for rpm/deb/tar-pkg with O=<subdir>
   - Fix for CONFIG_EXTRA_FIRMWARE"

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  firmware: Create directories for external firmware
  kbuild: Fix packaging targets with relative $(srctree)
  kbuild: Do not print the build directory with make -s

Pull ACPI and power management fixes from Rafael Wysocki:
 "These are a few regression fixes for ACPI device enumeration and
  resources management, intel_pstate and cpufreq, a revert of an ACPI
  commit removing user space interfaces in /proc that we incorrectly
  thought were not used any more, fixes for some long-standing
  concurrency issues in the ACPI EC driver, two ACPI battery driver
  fixes, stable-candidate fixes for intel_pstate, an ACPI-related fix
  for i915 and two new ACPI video blacklist entries for Win8-oriented
  BIOSes.

  Specifics:

   - Missing device ID for ACPI enumeration of PNP devices that we
     overlooked during the recent rework of that code from Zhang Rui.

   - Fix for a problem introduced during the 3.14 cycle in the ACPI
     device resources management code and causing it to reject all
     resources of length 0 although some of them are actually valid
     which affects serial ports detection on a number of systems.  From
     Andy Whitcroft.

   - intel_pstate fix for a boot problem on some BayTrail-based systems
     introduced by a previous fix related to that platform during the
     3.13 cycle from Dirk Brandewie.

   - Revert of a 3.13 commit that removed the ACPI AC /proc interface
     which turns out to be still needed by some old utilities
     (kpowersave from kde 3.5.10 in particular) from Lan Tianyu.

   - cpufreq build fix for the davinci ARM platform from Prabhakar Lad
     (the breakage was introduced during the 3.10 cycle).

   - ACPI-related i915 fix preventing firmware on some Thinkpad laptops
     from setting backlight levels incorrectly during AC plug/unplug.
     From Aaron Lu.

   - Fixes for two nasty race conditions in the ACPI embedded controller
     driver that may be responsible for a number of past bug reports
     related to the EC from Lv Zhang and a fix for two memory leaks in
     error code paths in that driver from Colin Ian King.

   - Fixes for a couple of corner-case issues in the intel_pstate driver
     (all candidates for -stable) from Dirk Brandewie and Vincent Minet.

   - Fixes for two corner-case issues in the ACPI battery driver from
     Josef Gajdusek and Lan Tianyu.

   - Two new ACPI video blacklist entries for Acer TravelMate B113 and
     Dell Inspiron 5737 from Edward Lin and Martin Kepplinger"

* tag 'pm+acpi-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PNP: add soc_button_array device ID to PNP IDs list
  cpufreq: Makefile: fix compilation for davinci platform
  ACPI / video: Add Acer TravelMate B113 to native backlight blacklist
  ACPI / video: Add Dell Inspiron 5737 to the blacklist
  ACPI / i915: ignore firmware requests for backlight change
  ACPI / battery: fix wrong value of capacity_now reported when fully charged
  ACPI / resources: only reject zero length resources based at address zero
  ACPI / battery: Retry to get battery information if failed during probing
  ACPI / EC: Free saved_ec on error exit path
  ACPI / EC: Add detailed fields debugging support of EC_SC(R).
  ACPI / EC: Update revision due to recent changes
  ACPI / EC: Fix race condition in ec_transaction_completed()
  ACPI / EC: Remove duplicated ec_wait_ibf0() waiter
  ACPI / EC: Add asynchronous command byte write support
  ACPI / EC: Avoid race condition related to advance_transaction()
  intel_pstate: Set CPU number before accessing MSRs
  intel_pstate: Update documentation of {max,min}_perf_pct sysfs files
  intel_pstate: don't touch turbo bit if turbo disabled or unavailable.
  intel_pstate: Fix setting VID
  Revert "ACPI / AC: Remove AC's proc directory."

This new request drops the pageflipping fixes for now.  Just a few small
fixes for dpm, DP, and a fix for a hang on boot evergreen.

* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon/dpm: Reenabling SS on Cayman
  drm/radeon: fix typo in ci_stop_dpm()
  drm/radeon: fix typo in golden register setup on evergreen
  drm/radeon: only print meaningful VM faults
  drm/radeon/dp: return -EIO for flags not zero case

Replace open-coded test for empty tx ring buffer with equivalent
helper function, uart_circ_empty(). No functional change.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 717f3bba,
'serial_core: Fix conditional start_tx on ring buffer not empty'
exposes an incorrect assumption in several drivers' start_tx methods;
the tx ring buffer can, in fact, be empty when restarting tx while
performing flow control.

Affected drivers:
sunsab.c
ip22zilog.c
pmac_zilog.c
sunzilog.c
m32r_sio.c
imx.c

Other in-tree serial drivers either are not affected or already
test for empty tx ring buffer before transmitting.

Test for empty tx ring buffer in start_tx() method, after transmitting
x_char (if applicable).
Reported-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Seth Bollinger <sethb@digi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Relying on static functions used just once to get inlined (and
subsequently have dead code paths eliminated) is wrong: Compilers are
free to decide whether they do this, regardless of optimization level.
With this not happening for vdso_addr() (observed with gcc 4.1.x), an
unresolved reference to align_vdso_addr() causes the build to fail.

[ hpa: vdso_addr() is never actually used on x86-32, as calculate_addr
  in map_vdso() is always false.  It ought to be possible to clean
  this up further, but this fixes the immediate problem. ]
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/53B5863B02000078000204D5@mail.emea.novell.comAcked-by: NAndy Lutomirski <luto@amacapital.net>
Tested-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Certain ld versions (observed with 2.20.0) put an empty .rela.dyn
section into shared object files, breaking the assumption on the number
of sections to be copied to the final output. Simply discard any empty
SHT_REL and SHT_RELA sections to address this.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/53B5861E02000078000204D1@mail.emea.novell.comAcked-by: NAndy Lutomirski <luto@amacapital.net>
Tested-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

It reverts commit c745fe61 now that
Cayman is stable since VDDCI fix. Spread spectrum was not the culprit.

This depends on b0880e87
(drm/radeon/dpm: fix vddci setup typo on cayman).
Signed-off-by: NAlexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Need to use the RREG32_SMC() accessor since the register
is an smc indirect index.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org