Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
大约 1 年 前同步成功

通知 158
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 23 10月, 2010 4 次提交
  3. 21 10月, 2010 1 次提交
  5. 18 10月, 2010 3 次提交
  7. 31 7月, 2010 4 次提交
    • K
      x86/PCI: use for_each_pci_dev() · 1f7979ac
      由 Kulikov Vasiliy 提交于 
      Use for_each_pci_dev() to simplify the code.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
      1f7979ac
    • B
      x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN · 2491762c
      由 Bjorn Helgaas 提交于 
      This DMI quirk turns on "pci=use_crs" for the ALiveSATA2-GLAN because
amd_bus.c doesn't handle this system correctly.

The system has a single HyperTransport I/O chain, but has two PCI host
bridges to buses 00 and 80.  amd_bus.c learns the MMIO range associated
with buses 00-ff and that this range is routed to the HT chain hosted at
node 0, link 0:

    bus: [00, ff] on node 0 link 0
    bus: 00 index 1 [mem 0x80000000-0xfcffffffff]

This includes the address space for both bus 00 and bus 80, and amd_bus.c
assumes it's all routed to bus 00.

We find device 80:01.0, which BIOS left in the middle of that space, but
we don't find a bridge from bus 00 to bus 80, so we conclude that 80:01.0
is unreachable from bus 00, and we move it from the original, working,
address to something outside the bus 00 aperture, which does not work:

    pci 0000:80:01.0: reg 10: [mem 0xfebfc000-0xfebfffff 64bit]
    pci 0000:80:01.0: BAR 0: assigned [mem 0xfd00000000-0xfd00003fff 64bit]

The BIOS told us everything we need to know to handle this correctly,
so we're better off if we just pay attention, which lets us leave the
80:01.0 device at the original, working, address:

    ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7f])
    pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xff37ffff]
    ACPI: PCI Root Bridge [PCI1] (domain 0000 [bus 80-ff])
    pci_root PNP0A08:00: host bridge window [mem 0xfebfc000-0xfebfffff]

This was a regression between 2.6.33 and 2.6.34.  In 2.6.33, amd_bus.c
was used only when we found multiple HT chains.  3e3da00c, which
enabled amd_bus.c even on systems with a single HT chain, caused this
failure.

This quirk was written by Graham.  If we ever enable "pci=use_crs" for
machines from 2006 or earlir, this quirk should be removed.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16007

Cc: stable@kernel.org
Reported-by: NGraham Ramsey <ramsey.graham@ntlworld.com>
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
      2491762c
    • M
      x86/PCI: Add option to not assign BAR's if not already assigned · 7bd1c365
      由 Mike Habeck 提交于 
      The Linux kernel assigns BARs that a BIOS did not assign, most likely
to handle broken BIOSes that didn't enumerate the devices correctly.
On UV the BIOS purposely doesn't assign I/O BARs for certain devices/
drivers we know don't use them (examples, LSI SAS, Qlogic FC, ...).
We purposely don't assign these I/O BARs because I/O Space is a very
limited resource.  There is only 64k of I/O Space, and in a PCIe
topology that space gets divided up into 4k chucks (this is due to
the fact that a pci-to-pci bridge's I/O decoder is aligned at 4k)...
Thus a system can have at most 16 cards with I/O BARs: (64k / 4k = 16)

SGI needs to scale to >16 devices with I/O BARs.  So by not assigning
I/O BARs on devices we know don't use them, we can do that (iff the
kernel doesn't go and assign these BARs that the BIOS purposely didn't
assign).

This patch will not assign a resource to a device BAR if that BAR was
not assigned by the BIOS, and the kernel cmdline option 'pci=nobar'
was specified.   This patch is closely modeled after the 'pci=norom'
option that currently exists in the tree.
Signed-off-by: NMike Habeck <habeck@sgi.com>
Signed-off-by: NMike Travis <travis@sgi.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
      7bd1c365
    • J
      x86/PCI: pci, fix section mismatch · 73cd3b43
      由 Jiri Slaby 提交于 
      pcibios_scan_specific_bus calls pci_scan_bus_on_node which is
__devinit. Mark pcibios_scan_specific_bus __devinit as well since
all users are now __init or __devinit.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
      73cd3b43
  9. 17 7月, 2010 2 次提交
    • J
      x86, pci, mrst: Add extra sanity check in walking the PCI extended cap chain · f82c3d71
      由 Jacob Pan 提交于 
      The fixed bar capability structure is searched in PCI extended
configuration space.  We need to make sure there is a valid capability
ID to begin with otherwise, the search code may stuck in a infinite
loop which results in boot hang.  This patch adds additional check for
cap ID 0, which is also invalid, and indicates end of chain.

End of chain is supposed to have all fields zero, but that doesn't
seem to always be the case in the field.
Suggested-by: N"H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <1279306706-27087-1-git-send-email-jacob.jun.pan@linux.intel.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>
      f82c3d71
    • B
      PCI: fall back to original BIOS BAR addresses · 58c84eda
      由 Bjorn Helgaas 提交于 
      If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.

Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.

Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero.  Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.

This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.

I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address.  But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263Reported-by: NAndrew <nitr0@seti.kr.ua>
Tested-by: NAndrew <nitr0@seti.kr.ua>
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
      58c84eda
  11. 12 6月, 2010 1 次提交
  13. 25 5月, 2010 1 次提交
  15. 22 5月, 2010 1 次提交
  17. 19 5月, 2010 1 次提交
  19. 17 5月, 2010 1 次提交
  21. 15 5月, 2010 1 次提交
  23. 12 5月, 2010 2 次提交
  25. 10 5月, 2010 3 次提交
  27. 29 4月, 2010 1 次提交
  29. 27 4月, 2010 1 次提交
  31. 23 4月, 2010 1 次提交
  33. 09 4月, 2010 1 次提交
  35. 04 4月, 2010 1 次提交
  37. 30 3月, 2010 1 次提交
    • T
      include cleanup: Update gfp.h and slab.h includes to prepare for breaking... · 5a0e3ad6
      由 Tejun Heo 提交于 
      include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
      5a0e3ad6
  39. 26 3月, 2010 2 次提交
  41. 25 3月, 2010 1 次提交
  43. 26 2月, 2010 3 次提交
  45. 25 2月, 2010 1 次提交
  47. 24 2月, 2010 2 次提交