Currently firmware is configured to filter out beacons. In case
a beacon was changed - it is waking the host.
However, some vendors change their IEs frequently without any
significant change, and redundant wakeups are triggered as a
result.
As a solution disable beacon filtering when entering d0i3.
Instead, firmware will store the latest beacon and upon exiting
d0i3 it will send it up to the host, so the host can act upon
changes (if there were any).
This beacon will arrive as a dedicated notification - support it
as well.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

No need to include net/ip6_checksum.h twice.
Remove TODOs.
Remove trailing space.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to let the fw do offloading properly, we need
to provide various key data (e.g. PN).

Configure the params on d0i3 entrance, and update them
back on d0i3 exit.

Since d3 code is now called in d0i3 which requires runtime
pm only, make d3.0 depend on CONFIG_PM (rather than
CONFIG_PM_SLEEP), and add required #ifdefs and wrappers
where needed, so both CONFIG_PM=n and CONFIG_PM_RUNTIME=n
configurations will build correctly.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Incoming hardware will send frame release notifications to
the reorder buffer in order to update with the BA session
status and up to date NSSN.
This patch enables the API.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Convert the convert the new infrastructure added by previous
patches to actually use the new RX descriptor layout.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Firmware will support filtering multicast L3 packets.
The L3 filtering is configured by the WOWLAN_CONFIG command.
All flags should be enabled by default.
Older firmware is not affected as it does not look into
this field.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow to configure the driver to pretend to have TX CSUM
offload support. This will be useful to test the TSO flows
that will come in further patches.
This configuration is disabled by default.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

RFC4862 states that "In all cases, a node MUST NOT respond to
a Neighbor Solicitation for a tentative address".
Currently the driver configures the NS offload and does not wait
for address to become permanent, thus violating the RFC.
Just removing the address from the address list is not good enough
for all cases, since the NS messages are needed for the duplicate
address detection and should not be discarded.

For d0i3 disable NS offload. Put tentative address in the address
list so the NS packet will not be filtered out by ucode.
For D3 the platform will not wake from NS packets - so enable
NS offload while removing the tentative address from the list.

Given that now NS offload might be disabled, and that the ucode
uses the IP data for other puroposes (L3 filtering) add two
independent flags indicating if IPv4\IPv6 data is valid.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

d0i3 commands are not supported in the init image, so take
a reference to ensure we don't enter d0i3 during init image,
and additional checks to prevent d0i3 commands when no
fw image is loaded.

Add a few WARN_ON_ONCE to the d0i3 enter/exit commands
to ensure we send d0i3 commands only when the normal
ucode is loaded.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Host commands now have a group id, express this in printed messages.
Signed-off-by: NSharon Dvir <sharon.dvir@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We send an ADD_STA to instruct the firmware to release
frames despite the peer being in PS.
Since the ADD_STA command and the Tx frame that comes
immediately afterwards can be reordered by the DMA engine,
we need to block the Tx queues until the firmware replies
with the ADD_STA response.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There is no reason to keep a reference when the interface is down,
since we are not really doing anything.  The reference is only needed
when the mac80211 start op (or a hw restart) is running, to prevent
going into runtime or system supend in the meantime.  This will allow
us to support runtime PM when the interface is down (in another
patch).
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Define the RX API that's used by the 9000 series hardware.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add ability to set the continuous recording mode of the FW, while
the FW debug data is configured to be stored on the NIC.
This could be useful for storing large segments of FW usniffer
debug data on the host, while having small store space on the NIC.
The host receives the usniffer data through the regular RX path, and
the data can get extracted using trace-cmd.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The fw debug functionality is big enough to warrant
a separate file. Move existing related functions to the new file.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There is a potential race condition when entering suspend with d0i3 in
PCIe.  If there is a frame queued just before we suspend, it won't
complete and we will never clear the queue stuck timer.  To solve
this, call TX_PATH_FLUSH to flush all queues (except the command
queue) as part of the d0i3 entry process.  Add a new function that
returns all the flushable queues.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This was an old workaround for solving latency issues with
certain Miracast adapters like ActionTec. However this isn't
needed anymore and furthermore it hurts throughput in other
use cases.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the netdetect debugfs entry was removed, the nd_config element
was accidentally left in the iwl_mvm structure.  Remove it.

Fixes: dbb04b0d ("iwlwifi: mvm: remove netdetect debugfs entry")
Reported-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

802.11ac allows A-MSDU that can be up to 12KB long. Since
an entire A-MSDU needs to fit into one single Receive
Buffer (RB), add support for big RBs.
Since this adds lots of pressure to the memory manager and
significantly increase the true_size of the RX buffers,
don't enable this by default.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the option to configure multiple 'scan plans' for scheduled scan.
Each 'scan plan' defines the number of scan cycles and the interval
between scans. The scan plans are executed in the order they were
configured. The last scan plan will always run infinitely and thus
defines only the interval between scans.
The maximum number of scan plans supported by the device and the
maximum number of iterations in a single scan plan are advertised
to userspace so it can configure the scan plans appropriately.

When scheduled scan results are received there is no way to know which
scan plan is being currently executed, so there is no way to know when
the next scan iteration will start. This is not a problem, however.
The scan start timestamp is only used for flushing old scan results,
and there is no difference between flushing all results received until
the end of the previous iteration or the start of the current one,
since no results will be received in between.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since the new multi-queue capability depends on a new firmware API,
we can already add some code for it. If the new API is present, a
new opmode ops struct is used that handles the new rx_rss method.

For now, only restructure the RX handling to distinguish between
the two. Future patches will convert the new infrastructure to
actually use the new RX descriptor layout.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

"DQA" is shorthand for "dynamic queue allocation", with the
idea of allocating queues per-RA/TID on-demand rather than
using shared queues statically allocated per vif. The goal
of this is to enable future features (like GO PM) and to
improve performance measurements of TX traffic.

When RA/TID streams can't be neatly sorted into different AC
queues, DQA allows sharing queues for the same RA. This means
that DQA allows different ACs may reach the same HW queue.

Update the code to allow such queue sharing by having a mapping
between the HW queue and the mac80211 queues using it (as this
could be more than one queue).
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Treat PHY RX specially, since it's actually pretty frequent,
doesn't need all the notication etc. code, and will have a
different handler in future hardware.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

FW dump may be triggered when running init ucode, for example due to a
sysassert. In this case fw_dump_wk may run after mvm is freed, resulting
in a kernel panic.
Fix it by flushing the work.

Fixes: 01b988a708af ("iwlwifi: mvm: allow to collect debug data when restart is disabled")
Cc: <stable@vger.kernel.org> [3.18+]
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Move the DTS measurement command and notification from short
command header to the new PHY command group for firmware
supporting the extended command headers.
Signed-off-by: NAviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to verify d0i3 flow, add debug print to indicate
d0i3 exit was completed (right after tx was re-enabled),
along with the wakeup reasons.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Recent fw version added assert to make sure wowlan configuration
is configured only when a station is connected.

Change the driver behavior to pass this configuration only
if we indeed have ap station id (i.e. connected).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

ECHO_CMD is a simple command that can be sent to the
firmware just to check that it is alive.
This command is useful for debug purpose, provide a debugfs
hook to send it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

The command string array is assumed to be indexable by a full u8, so it
must have 256 entries (0-255), not just 255. A recent firmware change
(apparently) started using the command 0xff for a notification to the
host, causing the driver to crash in debug message/tracing code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we enter D0i3, we must stop TXing otherwise the
sequence number we use might conflict with the firmware's
internal TX. In order to do so, we have
IWL_MVM_STATUS_IN_D0I3 which should prevent any Tx while we
enter D0i3. There is a bug in this code since we may Tx even
if IWL_MVM_STATUS_IN_D0I3 is set. This can happen as long as
mvm->d0i3_ap_sta_id is not set.

To make sure that we don't have any packet in the Tx path
while we set mvm->d0i3_ap_sta_id, call synchronize_net only
after we already set mvm->d0i3_ap_sta_id.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently if we wake up during D0I3 due to beacon loss we disconnect
immediately. This behaviour causes redundant disconnection, which could
be prevented by polling as it is usually done in mac80211.
Instead, we prefer reporting beacon loss and let mac80211 try polling
before disconnection.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The mac80211 patch to pass the NAPI struct only changed iwlwifi to
store the NAPI struct, but we can do better: pass it directly from
the lower transport layer to the opmode during RX, and then on to
mac80211 from there.

When we add multiple RX queues, we can then pass the appropriate
NAPI struct properly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.

In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.

When the device is slave on the bus(SDIO) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. When the FW wants load / unload pages, it creates an
interrupt,	and the driver uploads / downloads the page to an address in
the a specific address on the device's memory.

The driver can support up to 1 MB of pages.

Add paging mechanism for the UMAC on SDIO in order to allow the program to
use a larger virtual space while using less physical memory on the device
itself.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Change the FW debug trigger tlv to include a monitor only
option. Setting this option to true will cause fw dump triggers
to only collect monitor data and skip other dumps such as
SMEM, SRAM, CSR, PRPH, etc.
This option is used when accessing the different parts of the
firmware memory is not wanted and can cause unwanted behavior
like when debugging TX latency.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.

In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.

When the device is master on the bus(PCI) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. The FW can load / unload the pages on its own.

The driver can support up to 1 MB of pages.

Add paging mechanism for the UMAC on PCI in order to allow the program
to use a larger virtual space while using less physical memory on the
device.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support for extended command id in triggers handling.
Extended command id header contains group id in addition to command id.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support for extended firmware event header that contains
a group id as well as the command id.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As the firmware is slowly running out of command IDs and grouping of
commands is desirable anyway, the firmware is extending the command
header from 4 bytes to 8 bytes to introduce a group (in place of the
former flags field, since that's always 0 on commands and thus can
be easily used to distinguish between the two.

In order to support this most easily in the driver widen the command
command ID used in the command sending functions and encode the new
values (group and version) in the ID. That way existing code doesn't
have to be changed (since the higher bits are 0 automatically) and
newer code can easily use the new ID generation function to create a
value to use in place of just the command ID.
Signed-off-by: NAviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>