Conflicts:
	net/bluetooth/l2cap_core.c

Now that there is a one-to-one correspondance between neighbour
and hh_cache entries, we no longer need:

1) dynamic allocation
2) attachment to dst->hh
3) refcounting

Initialization of the hh_cache entry is indicated by hh_len
being non-zero, and such initialization is always done with
the neighbour's lock held as a writer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: core: Bus width testing needs to handle suspend/resume

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  SUNRPC: Fix use of static variable in rpcb_getport_async
  NFSv4.1: update nfs4_fattr_bitmap_maxsz
  SUNRPC: Fix a race between work-queue and rpc_killall_tasks
  pnfs: write: Set mds_offset in the generic layer - it is needed by all LDs

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  kbuild: Do not write to builddir in modules_install

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms/evergreen: emit SQ_LDS_RESOURCE_MGMT for blits
  agp/intel: Fix typo in G4x_GMCH_SIZE_VT_2M
  drm/radeon/kms: fix typo in read_disabled vbios code
  drm/radeon/kms: use correct BUS_CNTL reg on rs600
  drm/radeon/kms: fix backend map typo on juniper
  drm/radeon/kms: fix regression in hotplug

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
  slip: fix wrong SLIP6 ifdef-endif placing
  natsemi: fix another dma-debug report
  sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
  net: Fix default in docs for tcp_orphan_retries.
  hso: fix a use after free condition
  net/natsemi: Fix module parameter permissions
  XFRM: Fix memory leak in xfrm_state_update
  sctp: Enforce retransmission limit during shutdown
  mac80211: fix TKIP replay vulnerability
  mac80211: fix ie memory allocation for scheduled scans
  ssb: fix init regression of hostmode PCI core
  rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
  ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
  carl9170: add NEC WL300NU-AG usbid
  cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
  ath5k: fix incorrect use of drvdata in PCI suspend/resume code
  ath5k: fix incorrect use of drvdata in sysfs code
  Bluetooth: Fix memory leak under page timeouts
  Bluetooth: Fix regression with incoming L2CAP connections
  Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
  ...

On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.

On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.

This fixes a regression introduced in 3.0-rc1 by 08ee80cc
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This following code contains a dead "if (dev).." block:
        ...
        for (i = 0; i < slip_maxdev; i++) {
                dev = slip_devs[i];
                if (dev == NULL)
                        break;
        }
        /* Sorry, too many, all slots in use */
        if (i >= slip_maxdev)
                return NULL;

        if (dev) {
                sl = netdev_priv(dev);
                if (test_bit(SLF_INUSE, &sl->flags)) {
                        unregister_netdevice(dev);
                        dev = NULL;
                        slip_devs[i] = NULL;
                }
         }
        ...
The reason is that the code starting with "if (dev).." is never called as
when we found an empty slot (dev == NULL) we break the loop and "if (dev).."
not works eiter the loop ends and we get out with "i >= slip_maxdev".
Signed-off-by: NMatvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As slip_devs is initialized on module load stage there is no reason to
check it for NULL anywhere instead of the deinitialization routine because
if we can't get enough memory on startup we don't run at all.
Signed-off-by: NMatvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In sl_realloc_bufs() there is no reason to check if the requested MTU greater
than or equal to the current MTU value as this function called only
when requested
MTU not equals to the current value. So, the ">=" operation can be
safely replaced
with the ">".
Signed-off-by: NMatvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMatvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This never, ever, happens.

Neighbour entries are always tied to one address family, and therefore
one set of dst_ops, and therefore one dst_ops->protocol "hh_type"
value.

This capability was blindly imported by Alexey Kuznetsov when he wrote
the neighbour layer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of all of the useless and costly indirection
by doing the neigh hash table lookup directly inside
of the neighbour binding.

Rename from arp_bind_neighbour to rt_bind_neighbour.

Use new helpers {__,}ipv4_neigh_lookup()

In rt_bind_neighbour() get rid of useless tests which
are never true in the context this function is called,
namely dev is never NULL and the dst->neighbour is
always NULL.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compute drivers may change this, so make sure to emit it to
avoid errors in bo blits.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39119Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Konstantin Belousov found an error in the define of G4x_GMCH_SIZE_VT_2M
relative to the GMCH specs, and confirmed that indeed one of his users
with a Q45 reports 0xb not 0xc for a 2/2MiB GATT.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Konstantin Belousov <kostikbel@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

v2: incorporated suggestions from Randy Dunlap
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we cannot allocate new skbs in RX completion handler, we should
increase netdevice rx_dropped counter, not spam console messages.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In process and sleep allowed context, favor GFP_KERNEL allocations over
GFP_ATOMIC ones.

-v2: fixed checkpatch.pl warnings

CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ben Greear <greearb@candelatech.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the Jumbo Frames feature on 82583 devices.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/mm: Fix memory_block_size_bytes() for non-pseries
  mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  pcmcia: pxa2xx/vpac270: free gpios on exist rather than requesting
  ARM: pxa/raumfeld: fix device name for codec ak4104
  ARM: pxa/raumfeld: display initialisation fixes
  ARM: pxa/raumfeld: adapt to upcoming hardware change
  ARM: pxa: fix gpio_to_chip() clash with gpiolib namespace
  genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
  arm: mach-vt8500: add forgotten irq_data conversion
  ARM: pxa168: correct nand pmu setting
  ARM: pxa910: correct nand pmu setting
  ARM: pxa: fix PGSR register address calculation

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
  Revert "drm/i915: enable rc6 by default"
  drm/i915: Clean up i915_driver_load failure path
  drm/i915: Enable GPU reset on Ivybridge.
  drm/i915/dp: manage sink power state if possible
  drm/i915/dp: consolidate AUX retry code
  drm/i915/dp: remove DPMS mode tracking from DP
  drm/i915/dp: try to read receiver capabilities 3 times when detecting
  drm/i915/dp: read more receiver capability bits on hotplug
  drm/i915/dp: use DP DPCD defines when looking at DPCD values
  drm/i915/dp: retry link status read 3 times on failure

Almost all of these have long outstayed their welcome.

And for every one of these macros, there are 10 features for which we
didn't add macros.

Let's just delete them all, and get out of habit of doing things this
way.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Because struct rpcbind_args *map was declared static, if two
threads entered this method at the same time, the values
assigned to map could be sent two two differen tasks.
This could cause all sorts of problems, include use-after-free
and double-free of memory.

Fix this by removing the static declaration so that the map
pointer is on the stack.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Cc: stable@kernel.org
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

...which is measured by the size and not the amount of space remaining.

Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:

[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

This reverts commit a51f7a66.

We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: NKeith Packard <keithp@keithp.com>

i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.

i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.

i915_driver_load also has some incorrect gotos in the error cleanup
paths:

 * After failing to initialize the GTT (which cannot happen, btw,
   intel_gtt_get returns a fixed (non-NULL) value), it tries to
   free the uninitialized WC IO mapping. Fixed this by changing the
   target from out_iomapfree to out_rmmap
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NLin Ming <ming.m.lin@intel.com>

The driver reads PCI subsystem IDs from the PCI configuration registers while
it is already stored by the PCI subsystem in the 'subsystem_device' field of
'struct pci_dev'...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let depmod.sh create a temporary directory in /tmp instead of writing to
the build directory as root. The mktemp utility should be available on
any recent system (and there is already scripts/gen_initramfs_list.sh
relying on it).
Reported-by: NChristian Kujau <lists@nerdbynature.de>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

BUS_CNTL reg and bits moved between pre-PCIE and PCIE asics.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

BUS_CNTL is at 0x30 on rs600, not 0x4c.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Don't enable backends that don't exist.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Skip connectors that do not have an HPD pin.

Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=39027Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Tested-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Make sure that the 'static' keywork is at the beginning of declaration
for drivers/net/usb/kalmia.c

This gets rid of warnings like
  warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SLIP6 have nothing to do with CSLIP so placing a block of
SLIP6-related code within a CSLIP ifdef-endif block is incorrect.
Signed-off-by: NIlya Matvejchikov <matvejchikov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently can free inetpeer entries too early :

[  782.636674] WARNING: kmemcheck: Caught 32-bit read from uninitialized memory (f130f44c)
[  782.636677] 1f7b13c100000000000000000000000002000000000000000000000000000000
[  782.636686]  i i i i u u u u i i i i u u u u i i i i u u u u u u u u u u u u
[  782.636694]                          ^
[  782.636696]
[  782.636698] Pid: 4638, comm: ssh Not tainted 3.0.0-rc5+ #270 Hewlett-Packard HP Compaq 6005 Pro SFF PC/3047h
[  782.636702] EIP: 0060:[<c13fefbb>] EFLAGS: 00010286 CPU: 0
[  782.636707] EIP is at inet_getpeer+0x25b/0x5a0
[  782.636709] EAX: 00000002 EBX: 00010080 ECX: f130f3c0 EDX: f0209d30
[  782.636711] ESI: 0000bc87 EDI: 0000ea60 EBP: f0209ddc ESP: c173134c
[  782.636712]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  782.636714] CR0: 8005003b CR2: f0beca80 CR3: 30246000 CR4: 000006d0
[  782.636716] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[  782.636717] DR6: ffff4ff0 DR7: 00000400
[  782.636718]  [<c13fbf76>] rt_set_nexthop.clone.45+0x56/0x220
[  782.636722]  [<c13fc449>] __ip_route_output_key+0x309/0x860
[  782.636724]  [<c141dc54>] tcp_v4_connect+0x124/0x450
[  782.636728]  [<c142ce43>] inet_stream_connect+0xa3/0x270
[  782.636731]  [<c13a8da1>] sys_connect+0xa1/0xb0
[  782.636733]  [<c13a99dd>] sys_socketcall+0x25d/0x2a0
[  782.636736]  [<c149deb8>] sysenter_do_call+0x12/0x28
[  782.636738]  [<ffffffff>] 0xffffffff
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct e1000_queue_stats is not used, lets remove it
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>