This is fully backward compatible with older platforms.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In some rare cases, the firmware can put the device to
sleep after the driver requested the access. This is
because the access request can take a short time to be
propagated to the firmware.

If that happens, the driver may think that it has access
since the firmware hasn't put the device to sleep yet, but
right after the driver's check, the firmware might put the
device to sleep.

Warn when this happens by allowing the firmware to finish
the "put the device sleep" flow so that the driver will
not get access to the device. This will make the issue
visible.

This still doesn't fix the race, but at least it makes
it more visible.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently, the firmware only sends temperature notificaitions inside
RX statistics notifications, which are tied to beacon filtering.  This
is a problem because beacon filtering is not used with vifs that don't
receive beacons (e.g. P2P GO and AP), so the driver doesn't receive
temperature notifications in those cases.  To solve that, the firmware
will be changed so that it sends DTS_MEASUREMENT_NOTIFICATIONs,
independently from the beacon filtering flows.

To support that, the driver needs to also handle unsolicited
DTS_MEASUREMENT_NOTIFICATIONs, that are not triggered by
DTS_TRIGGER_CMD_FLAGS_TEMP requests.

This change is backwards compatible and will simply not be used with
firmware versions that do not send the notifications.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Refactor the temperature handling code so that it is easier to reuse
it with other notification flows.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The code to capture firmware errors works during the reconfiguration
phase after an error. As the D3->D0 transition uses the same flow to
get the D0 image reconfigured, this triggered and caused a firmware
coredump to be collected. This in turn, if it isn't picked up by
userspace, can cause module unloading to fail, which is how the bug
was detected.

To fix this issue, introduce a new status flag (D3_RECONFIG) and use
it to detect that during reconfiguration no coredump should be taken
and reported.
Reported-by: NAvi Kraif <avix.kraif@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we need only one antenna, we should refrain from using
the antenna that is shared with BT if BT load is high.
Fix this.
Reviewed-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When Tx STBC is being used and RS switches to a search column
using the alternate antenna from the current one there is a
problem with using rs_rate_match to figure out which table
is the active and which one is the search one. The root cause
is because in STBC the antenna mask in the ucode rate is set
to ANT_AB and in this specific scenario it matches both the
active and search table (e.g. SISO_ANT_A and SISO_ANT_B).
This leads to tx stats being updated in the wrong table and later
on to getting stuck in a test window and not moving on to other
columns. If this happens during the initial search cycle we
never end it and therefore never enable aggregation which leads
naturally to severe througput degradation.
Fix it by deducing which table is which by knowing whether we're
in a search or not like it's being done in rs_rate_scale_perform
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Other contexts might call iwl_mvm_ref_sync() right before
we set IWL_MVM_STATUS_IN_D0I3, and then assume the fw/bus
is not in d0i3 state.

However, since we currently don't check for held references
in the d0i3_enter flow, we might enter d0i3 although there
is an active reference.

Solve it by aborting the d0i3 enter flow if there is an
active reference. Since users are assumed to use
iwl_mvm_ref_sync, which takes a ref before checking the
flag, we don't need further locking.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This was taken care of in case we're doing STBC with HT
but not when working with VHT.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Even if running the driver with param init_dbg=1 - on INIT
image error - iwl_trans_stop_device() was still called. This
patch fixes that and calls iwl_trans_stop_device() on INIT
image failure only if init_dbg=0.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The variable 'tid' is already defined in this function, so use
just 't' for the new one. As we return from the function just
overwriting 'tid' would be acceptable, but less obvious to the
reader.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Mostly functions related to building Tx-commands for sending to FW.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The status variable should be unsigned as the function call
requires a u32 not int pointer, fix that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_trans_update_sf can fail and this wasn't handled.
Fix this.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix my mistake while sending Johannes's

commit aadede6e
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Thu Oct 9 17:01:36 2014 +0200

    iwlwifi: mvm: port to devcoredump framework
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The scan reference wasn't released in case of offloaded scan,
causing the refcount to go wrong and prevent the device
from going into d0i3.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

STBC is enabled on HT/VHT SISO rates in case we don't care
about power consumption and it won't hurt BT.
This is done only in case the peer and our chip support STBC
of course.
While at it fixed a bug which was causing bw and ldpc
flags to be set incorrectly in the rate scale table in case
we are switching to a legacy Tx column. This had no real impact.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Scan condition iterator assumes that an interface is associated if
phy_ctxt is assigned, but this isn't the sutuation in P2P device.
OTOH P2P device is never associated so we can simply ignore it.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi features a debug mechanism that allows to dump
binary data which is helpful to debug the firmware.
Until now, this data was made available for the userspace
through debugfs. For this exact purpose, devcoredump was
created. Move to the new infrastructure.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

These chips support STBC in both Tx and Rx.
Given that we've added STBC Tx support enable it.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.

Add parentheses around the mask.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We used to need to include some headers in order to read the registers
and do all the calculations by ourselves, but this is not done anymore
(i.e. we let the firmware do this for us), so we don't need to include
those headers anymore.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For WMM-AC we may have to be changing QoS parameters while the
queues are being flushed. This is not relevant in the "drop"
case, but matters when we wait for the device to finish the
transmissions.

To allow this, do the actual waiting without holding the mutex.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The warning gives no information about the frame, and presents
the flags so that one might think they're the frame. Clarify
and add more information.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes it easier to tune the values during the testing.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It is unused and won't be available in some future invocations of the
function.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The MVM_FW_BCAST_FILTER_PASS_ALL option defined in iwl-dbg-cfg.ini
configuration file allows to enable/disable FW broadcast filtering.

If MVM_FW_BCAST_FILTER_PASS_ALL is not defined in iwl-dbg-cfg.ini or
its value is 0, the mvm broadcast filtering is enabled.

Setting MVM_FW_BCAST_FILTER_PASS_ALL=1 in iwl-dbg-cfg.ini blocks sending
of BCAST_FILTER_CMD to FW.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is were it really needs to be.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In the new format the "CSS section" has the same TLV type
as the "mem section". So we need to run the secured flow
for all the 8000 products.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the ARC is reset when we exit from Sx in case we had
WoWLAN running, we can't access the prph before we reset
the NIC.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Otherwise we have no way to know that the buffer hasn't been
allocated.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A few slave bus devices show better performance when we
reduce the size of the Tx A-MPDU.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Getting the BSS station vif is something that may be needed by other
parts of the code.  So, instead of having an iterator specifically for
d3, change it into a generic one in utils.c.  Additionally, add a
iwl_mvm_get_bss_vif() function to make it easier to retrieving it.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Before we get all the chain (ie. mac80211, cfg80211, nl80211 and
userspace) changed to support net-detect, we can use this debugfs
entry for easy testing and as a proof of concept.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The net-detect feature will require a scan offload to be started in
the same way it is done now for scheduled scan.  Spin a new function
off of the sched_scan_start op code for reuse.  Additionally,
restructure the function a bit for more readability.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of checking if we are associated when suspending with wowlan
enabled in the interface iterator, allow it to return an unassociated
vif and move the check to the main suspend function.  This will be
needed by netdetect, since it should also work when we are not
associated but the vif is active.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Take the WoWLAN handling code out of the main suspend function,
dividing it into three parts: get_config (which is used before the
firmware is switched), switch_to_d3 (which handles the rebooting of
the hardware with the D3 firmware) and config (which configures the D3
firmware for WoWLAN operation).  This is necessary to prepare for the
net-detect implementation, which will use only the switch_to_d3 part
of this flow.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We use ieee80211_iter_keys() which requires the rtnl to be held.  If
we don't lock the rtnl, like we do when we suspend during a d3 test,
we get the following splat:

 RTNL: assertion failed at net/mac80211/key.c (566)
 CPU: 1 PID: 26529 Comm: cat Tainted: G        W  O 3.10.29-dev #1
 Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012
  e7b15008 e7b15008 e68adc1c c168aa62 e68adc54 f91f20b6 f923700c f9236fd8
  00000236 00000000 ece23874 00000000 f94941e0 00000000 e43b8e48 e7b15008
  00000000 e8b69e78 e68adcc0 f9493ab9 e68adc68 00000000 e43b8e48 e7b15008
 Call Trace:
  [<c168aa62>] dump_stack+0x16/0x18
  [<f91f20b6>] ieee80211_iter_keys+0x166/0x170 [mac80211]
  [<f94941e0>] ? iwl_mvm_query_wakeup_reasons+0x5f0/0x5f0 [iwlmvm]
  [<f9493ab9>] iwl_mvm_setup_connection_keep.isra.5+0x99/0x1d0 [iwlmvm]
  [<f9165e28>] ? cfg80211_report_wowlan_wakeup+0x308/0x510 [cfg80211]
  [<f9493fe5>] iwl_mvm_query_wakeup_reasons+0x3f5/0x5f0 [iwlmvm]
  [<c116125a>] ? init_object+0x3a/0x70
  [<f8a5b8ee>] ? iwl_trans_pcie_d3_resume+0x1be/0x3a0 [iwlwifi]
  [<f94956da>] __iwl_mvm_resume+0x14a/0x180 [iwlmvm]
  [<f9495736>] iwl_mvm_d3_test_release+0x26/0xc0 [iwlmvm]
  [<c117a64d>] __fput+0xad/0x210
  [<c117a7bd>] ____fput+0xd/0x10
  [<c10601a1>] task_work_run+0x81/0xb0
  [<c1040fa5>] do_exit+0x255/0xac0
  [<c104e511>] ? dequeue_signal+0x31/0x1a0
  [<c1041888>] do_group_exit+0x38/0xa0
  [<c10a6cfb>] ? trace_hardirqs_on+0xb/0x10
  [<c1051c31>] get_signal_to_deliver+0x1e1/0x8e0
  [<c104bd52>] ? try_to_del_timer_sync+0x42/0x60
  [<c104bd70>] ? try_to_del_timer_sync+0x60/0x60
  [<c168dc82>] ? schedule_timeout+0x102/0x2a0
  [<c10011ba>] do_signal+0x3a/0x8e0
  [<c104b190>] ? __internal_add_timer+0xb0/0xb0
  [<c168de7a>] ? schedule_timeout_interruptible+0x1a/0x20
  [<c104ce39>] ? msleep_interruptible+0x39/0x40
  [<f94939a9>] ? iwl_mvm_d3_test_read+0x49/0x70 [iwlmvm]
  [<c11797fc>] ? vfs_read+0x8c/0x160
  [<c11243af>] ? SyS_fadvise64_64+0x15f/0x2b0
  [<f9493960>] ? iwl_mvm_wowlan_program_keys+0x4a0/0x4a0 [iwlmvm]
  [<c1179a57>] ? SyS_read+0x57/0xa0
  [<c1001acf>] do_notify_resume+0x6f/0xa0
  [<c1692500>] work_notifysig+0x29/0x31

Fix this by hold the rtnl lock when calling __iwl_mvm_resume() in the
d3 test wake up path.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

mac80211 will never call rate_control_tx_status with a NULL
pointer for sta. Remove the superfluous check. This check
misled smatch.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The current TLC isn't optimized for low latency and some devices
have issues with MIMO. This kind of combo creates latency issues.
Allow to temporarily disable MIMO for tests in order to solve
the latency issues without the added complexity of MIMO.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>