Watermark line time registers for display low power watermark.

v2: improve bit names as suggested by Chris Wilson
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The WR PLL can drive the DDI ports at fixed frequencies for HDMI, DVI, DP
and FDI.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Those are used to control the display core clock.

v2: change the enable bit setting, spotted by Rodrigo Vivi.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Different registers are identified by their target id and offset. To
simplify their programming, they are called as <RegisterName><TargetId>.
For example, SSCCTL register accessed through SBI at target id 6 and
offset 0c is called SBI_SSCCTL6.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Multiple clocks can drive different outputs.

v2: use the port enums to access individual ports

v1 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This PLL control can drive DDI ports at desired frequencies for
DisplayPort and FDI connections.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pixel clock gating control for Lynx point.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Those are responsible for the Sideband Interface programming.

v2: rename SBI bits to better reflect their meaning
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Those registers are used to train DDI buffer translations for each link
type.

v2: access each port registers through the DDI_BUF_TRANS macro
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is one instance of those registers for each DDI port.

v2: access registers via the DDI_BUF_CTL() macro
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is one set of those registers for each port.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is one set of those registers for each pipe.

v2: use port enum to access individual registers
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is one set of such registers for each pipe (A/B/C/EDP).

v2: update to use DDI PORTS enum

v1 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There are 5 DDI ports on Haswell. Port A is always enabled, and is the one
connected to eDP, and Port E is the one that can be connected to the PCH
using FDI protocol.  Ports B, C, D and E can be used for digital outputs.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This defines the registers used by different power wells.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

ValleyView has a new interrupt architecture; best to put it in a new set
of functions.  Also make sure the ring mask functions handle ValleyView.

FIXME: fix flipping; need to enable interrupts and call prepare/finish
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

ValleyView handles force wake differently than previous chipsets, so add
a couple of new functions for it.  But leave it disabled by default
until we test it (need a chip with the Punit enabled first).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HDMI register offsets are different in Valleyview. Add support for the
same.

v2: drop superfluous comments in HDMI init (Daniel)
Signed-off-by: NBeeresh G <beeresh.g@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: NJesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch adds support for programming drain latency registers of Pondicherry
memory arbiter of Valleyview.

v2: clarify function names (Daniel)
    fix summary typo (Daniel)
v3: add parens (Ben)
    make drain function return bool (Ben)
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NGajanan Bhat <gajanan.bhat@intel.com>
Reviewed-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: NJesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Set required clock gating and chicken bits on VLV.

v2: set PIXEL_SUBSPAN_COLLECT_OPT_DISABLE too (Ben)
    move function below ivb version to pretend to be consistent (Ben)
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

ValleyView puts some display related registers like the PLL controls and
dividers behind the DPIO bus.  Add simple indirect register access
routines to get to those registers.

v2: move new wait_for macro to intel_drv.h (Ben)
    fix DPIO_PKT double write (Ben)
    add debugfs file
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add register definitions for the new VLV PLL bits.

v2: remove unused bits & regs (Ben)
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add support for ValleyView watermark handling.

v2: remove unused reg & bit definitions (Ben)
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is no GMBUS "disabled" port 0, nor "reserved" port 7.
For the other 6 ports there is a fixed 1:1 mapping between pin pairs and
gmbus ports, which means every real gmbus port has a gpio pin.

Given these realizations, clean up gmbus initialization.

Tested on Sandybridge (gen 6, PCH == CougarPoint) hardware.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to i915 documentation [1], "Port D" (DP/HDMI Port D) is
actually gmbus pin pair 6 (gmbus0.2:0 == 110b GPIOF), not 7 (111b).
Pin pair 7 is a reserved pair.

[1] Documentation for [DevSNB+] and [DevIBX], as found on
http://intellinuxgraphics.org:

[DevSNB+]:
http://intellinuxgraphics.org/documentation/SNB/IHD_OS_Vol3_Part3.pdf
 Section 2.2.2 lists the 6 gmbus ports (gpio pin pairs):
    [ 5: HDMI/DPD, 4: HDMIB, 3: HDMI/DPC, 2: LVDS, 1: SSC, 0: VGA ]
 2.2.2.1 lists the GPIO registers to control these 6 ports.
 2.2.3.1 lists the mapping between 5 of these gmbus ports and the 3
 Pin_Pair_Select bits (of the GMBUS0 register).  This table is missing
 HDMIB (port 101).

[DevIBX]: http://intellinuxgraphics.org/IHD_OS_Vol3_Part3r2.pdf
 Section 2.2.2 lists the same 6 gmbus ports plus two 'reserved' gpio
 ports.
 2.2.2.1 lists 8 GPIO registers... however, it says the size of the
 block is 6x32, which implies that those 2 reserved GPIO registers
 (GPIO_6 & GPIO_7) don't actually exist (or are irrelevant).
 2.2.3.1 lists the mapping between the 6 named gmbus ports and the 3
 Pin_Pair_Select bits (of the GMBUS0 register).  This table has HDMIB.

Note: the "reserved" and "disabled" pairs do not actually map to a
physical pair of pins, nor GPIO regs and shouldn't be initialized or used.
Fixing this is left for a later patch.

This bug had not been noticed earlier for two reasons:
 1) Until recently, "gmbus" mode was disabled - all transfers actually
    used "bit-bang" mode on GPIO port 5 (the "HDMI/DPD CTLDATA/CLK"
    pair), at register 0x5024 (defined as GPIOF i915_reg.h).
    Since this is the correct pair of pins for HDMI1, transfers succeed.

 2) Even if gmbus mode is re-enabled, the first attempted transaction
    will fail because it tries to use the wrong ("Reserved") pin pair.
    However, the driver immediately falls back again to the bit-bang
    method, which correctly uses GPIOF, so again, transfers succeed.

However, if gmbus mode is re-enabled and the GPIO fall-back mode is
disabled, then reading an attached monitor's EDID fail.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

They were all over the place, order them by position and add a few.

v2: add gen indications to the new bits (Ben)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was pointed by Jesse Barnes. The code now seems to follow the
specification but I don't have an SDVO device to really test this.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add register definitions for GTFIFODBG, and clear it during init time to
make sure state is correct.

This register tells us if either a read, or a write occurred while the
fifo was full. It seems like bit 2 is an OR of bit 0 and bit 1, so we
check that as well, but the documents are not quite clear.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by (v1): Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I'm not sure why they are needed (I didn't notice any difference in my
tests), but these bits are in our documentation and they are also set by
the Windows driver.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The hw seems to use this to correctly insert the required delay
before/after an even/odd interlaced field. This might also explain
why we need to substract 1 half-line from vtotal - if the hw just
adds the delay programmend in VSYNCSHIFT the total frame time would be
about that too long.

These registers seems to only exist on gen4 and later. For paranoia
also program it to 0 for progressive modes, but according to
documentation the hw should just ignore it in this case.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NAlfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- Clarify which bits are for which chips.
- Note that gen2 can't do interlaced directly (only via dvo tv chips).
- Move the mask to the top to make it clearer how wide this field is.
- Add defintions for all possible values.

This patch doesn't change any code.

v2: Paulo Zanoni pointed out that the pixel doubling modes do no
longer exist on ivb.

Cc: Peter Ross <pross@xvid.org>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NChristopher Egert <cme3000@gmail.com>
Tested-by: NAlfonso Fiore <alfonso.fiore@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split out for easier cross-checking of the boring pieces with bspec.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This just adds the setup and teardown code for the ppgtt PDE and the
last-level pagetables, which are fixed for the entire lifetime, at
least for the moment.

v2: Kill the stray debug printk noted by and improve the pte
definitions as suggested by Chris Wilson.

v3: Clean up the aperture stealing code as noted by Ben Widawsky.

v4: Paint the init code in a more pleasing colour as suggest by Chris
Wilson.

v5: Explain the magic numbers noticed by Ben Widawsky.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have to do this manually. Somebody had a Great Idea.

I've measured speed-ups just a few percent above the noise level
(below 5% for the best case), but no slowdows. Chris Wilson measured
quite a bit more (10-20% above the usual snb variance) on a more
recent and better tuned version of sna, but also recorded a few
slow-downs on benchmarks know for uglier amounts of snb-induced
variance.

v2: Incorporate Ben Widawsky's preliminary review comments and
elaborate a bit about the performance impact in the changelog.

v3: Add a comment as to why we don't need to check the 3rd memory
channel.

v4: Fixup whitespace.
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was pretty handy when figuring out what exactly went wrong with
ppgtt and it might also be useful when we stop filling the entire gart
with scratch page entries.

Also add the gen6+ DONE reg while at it.

v2: Chris Wilson suggested to allocate the error_state with kzalloc
for better paranoia. Also kill existing spurious clears of the
error_state while at it.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Based on a patch by Ben Widawsky, but with different colors
for the bikeshed.

In contrast to Ben's patch this one doesn't add the fault regs.
Afaics they're for the optional page fault support which
- we're not enabling
- and which seems to be unsupported by the hw team. Recent bspec
  lacks tons of information about this that the public docs released
  half a year back still contain.

Also dump ring HEAD/TAIL registers - I've recently seen a few
error_state where just guessing these is not good enough.

v2: Also dump INSTPM for every ring.

v3: Fix a few really silly goof-ups spotted by Chris Wilson.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The code already got unwieldy and we want to dump more per-ring
registers.

Only functional change is that we now also capture the video
ring registers on ilk.

v2: fixup a refactor fumble spotted by Chris Wilson.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It should be programmed to "0" for HDMI or "1" for DisplayPort.

This enables DisplayPort audio for

- HP EliteBook 8460p
  (whose BIOS does not set the N_value_index bit for us)

- DisplayPort monitor hot plugged after boot
  (otherwise most BIOS will fill the N_value_index bit for us)
Tested-by: NRobert Lemaire <rlemaire@suse.com>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Older specs claimed this was bit 11, but newer specs and the actual
simulator code say it was bit 12.  Regardless, we don't use MI_FLUSH,
or try to enable it any more.
Signed-off-by: NEric Anholt <eric@anholt.net>
Reviewed-by: NKenneth Graunke <kenneth@whitecape.org>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Anyone trying to use this bit, please read all the relevant
discussions, it's epic.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>