When we are resuming the UFS device rails in HPM mode, we are first
powering on the VCC rail while VCCQ and VCCQ2 rails still being in LPM
mode. Some UFS devices may take VCC on event as hint that host wants UFS
device to be resumed and may start drawing more power from the
VCCQ/VCCQ2 rails (while they are still in LPM mode) causing voltage drop
on these rails. This change fixes this issue by bringing VCCQ & VCCQ2
rails out of LPM before powering on VCC rail.
Reviewed-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently clock scaling is suspended only after the host and device are
put in low power mode but we should avoid clock scaling running after
UFS link is put in low power mode (hibern8). This change suspends clock
scaling before putting host/device in low power mode.
Reviewed-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If ufshcd pltfrm/pci driver's probe fails for some reason then ensure
that scsi host is released to avoid memory leak but managed memory
allocations (via devm_* calls) need not to be freed explicitly on probe
failure as memory allocated with these functions is automatically freed
on driver detach.
Reviewed-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

UFS devfreq clock scaling work may require clocks to be ON if it need to
execute some UFS commands hence it may request for clock hold before
issuing the command. But if UFS clock gating work is already running in
parallel, ungate work would end up waiting for the clock gating work to
finish and as clock gating work would also wait for the clock scaling
work to finish, we would enter in deadlock state. Here is the call trace
during this deadlock state:

Workqueue: devfreq_wq devfreq_monitor
	__switch_to
	__schedule
	schedule
	schedule_timeout
	wait_for_common
	wait_for_completion
	flush_work
	ufshcd_hold
	ufshcd_send_uic_cmd
	ufshcd_dme_get_attr
	ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div
	ufs_qcom_clk_scale_notify
	ufshcd_scale_clks
	ufshcd_devfreq_target
	update_devfreq
	devfreq_monitor
	process_one_work
	worker_thread
	kthread
	ret_from_fork

Workqueue: events ufshcd_gate_work
	__switch_to
	__schedule
	schedule
	schedule_preempt_disabled
	__mutex_lock_slowpath
	mutex_lock
	devfreq_monitor_suspend
	devfreq_simple_ondemand_handler
	devfreq_suspend_device
	ufshcd_gate_work
	process_one_work
	worker_thread
	kthread
	ret_from_fork

Workqueue: events ufshcd_ungate_work
	__switch_to
	__schedule
	schedule
	schedule_timeout
	wait_for_common
	wait_for_completion
	flush_work
	__cancel_work_timer
	cancel_delayed_work_sync
	ufshcd_ungate_work
	process_one_work
	worker_thread
	kthread
	ret_from_fork

This change fixes this deadlock by doing this in devfreq work (devfreq_wq):
Try cancelling clock gating work. If we are able to cancel gating work
or it wasn't scheduled, hold the clock reference count until scaling is
in progress. If gate work is already running in parallel, let's skip
the frequecy scaling at this time and it will be retried once next scaling
window expires.
Reviewed-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use le16_to_cpu only for accessing two byte data provided by controller.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Support Atomic Request Descriptors for Ventura/SAS35 devices.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

An UNMAP command on a PI formatted device will leave the Logical Block
Application Tag and Logical Block Reference Tag as all F's (for those LBAs
that are unmapped). To avoid IO errors if those LBAs are subsequently read
before they are written with valid tag fields, the MPI SCSI IO requests
need to set the EEDPFlags element EEDP Escape Mode field, Bits [7:6]
appropriately. A value of 2 should be set to disable all PI checks if the
Logical Block Application Tag is 0xFFFF for PI types 1 and 2.  A value
of 3 should be set to disable all PI checks if the Logical Block
Application Tag is 0xFFFF and the Logical Block Reference Tag is
0xFFFFFFFF for PI type 3.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For SAS35 devices MSIX vectors are inceased to 128 from 96. To support this
Reply post host index register count is increased to 16. Also variable
msix96_vector is replaced with combined_reply_queue and variable
combined_reply_index_count is added to set different values for SAS3 and
SAS35 devices.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added Device ID's for SAS35 devices (Ventura, Crusader, Harpoon &
Tomcat) and updated mpi header file for the same. Also added
"is_gen35_ioc" to MPT3SAS_ADAPTER structure for identifying SAS35 adapters.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Removing macro "MPT_DEVICE_TLR_ON" defined in header file as its unused
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When device missing event arrives, device_remove_in_progress bit will be
set and hence driver has to stop sending IOCTL commands.Now the check has
been added in IOCTL path to test device_remove_in_progress bit is set, if
so then IOCTL will be failed printing failure message.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Fix for incorrect numbers for MSIX vectors enabled when non RDPQ card is enumerated first.

No. of MSIX vectors supported = min (Total no. of CPU cores,
MSIX vectors supported by card)

when RDPQ is disabled "max_msix_vectors" module parameter which was
declared as global was set to '8' and hence if there are more than one card
in system among which if RDPQ disabled card is enumerated first then only 8
MSIX vectors was getting enabled for all the cards(including RDPQ enabled
card,which can support more than 8 MSIX vectors).

Used local variable instead of global variable ,if RDPQ is disabled this
local variable is set to '8' else it is set to "max_msix_vectors" (by
default this is set to -1, whose value can be set by user during driver
load time).So now regardless of whether RDPQ disabled card is enumerated
first or RDPQ enabled card is enumerated first , MSIX vectors enabled
depends on the cards capability.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Return value and Device_handle Arguments passed in correct order
 to match with its format string.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The advansys probe function tries to handle both ISA and PCI cases, each
hidden in an #ifdef when unused. This leads to a warning indicating that
when PCI is disabled we could be using uninitialized data:

drivers/scsi/advansys.c: In function  advansys_board_found :
drivers/scsi/advansys.c:11036:5: error:  ret  may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/scsi/advansys.c:10928:28: note:  ret  was declared here
drivers/scsi/advansys.c:11309:8: error:  share_irq  may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/scsi/advansys.c:10928:6: note:  share_irq  was declared here

This cannot happen in practice because the hardware in question only
exists for PCI, but changing the code to just error out here is better
for consistency and avoids the warning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

With the error message I added in "libfc: sanity check cpu number
extracted from xid" I didn't account for the fact that fc_exch_find is
called with FC_XID_UNKNOWN at the start of a new exchange if we are the
responder.

It doesn't come up with the initiator much, but that's basically every
exchange for a target.  By checking the xid for FC_XID_UNKNOWN first, we
not only prevent the erroneous error message, but skip the unnecessary
lookup attempt as well.

[mkp: applied by hand due to conflict with Hannes' libfc patch series]
Signed-off-by: NChris Leech <cleech@redhat.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In a case where gate work is called as part of cancel work from ungate
path the clk state would be marked as REQ_CLKS_ON.  There is no point
gating the clocks and then end up turning them ON immediately in ungate
work, save time by skipping the gate work and change the clk state to
CLKS_ON as they are not turned off yet.
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The ungate work turns on the clock before it exits hibern8, if the link
was put in hibern8 during clock gating work.  There occurs a race
condition when clock scaling work calls ufshcd_hold() to make sure low
power states cannot be entered, but that returns by checking only
whether the clocks are on.  This causes the clock scaling work to issue
UIC commands when the link is in hibern8 causing failures. Make sure we
exit hibern8 state before returning from ufshcd_hold().

Callstacks for race condition:

 ufshcd_scale_gear
 ufshcd_devfreq_scale
 ufshcd_devfreq_target
 update_devfreq
 devfreq_monitor
 process_one_work
 worker_thread
 kthread
 ret_from_fork

 ufshcd_uic_hibern8_exit
 ufshcd_ungate_work
 process_one_work
 worker_thread
 kthread
 ret_from_fork
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In case the power configuration fails, skip further processing of the
probing function and return immediately. This has 2 reasons:

1. Don't allow the UFS to continue running in PWM

2. Avoid multiple calls to pm_runtime_put_sync() when not in error
   handling or power management contexts
Signed-off-by: NDov Levenglick <dovl@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

During runtime resume operation, clock scaling may get indirectly
resumed via call to ufshcd_set_dev_pwr_mode(): Start/Stop Unit command
times out and SCSI error handling ultimately calls the host reset
handler to recover, during which clock scaling is resumed.  Error case
exit path of runtime resume will disable clocks.  As clock scaling was
already resumed, it will get scheduled later on and try to access UFS
registers while clocks are disabled, resulting in unclocked register
access.
Signed-off-by: NGilad Broner <gbroner@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

According to UFS device specification, sense data can be only 18 bytes
long, this change makes the changes accordingly.
Signed-off-by: NGilad Broner <gbroner@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add a write memory barrier to make sure descriptors prepared are
actually written to memory before ringing the doorbell. We have also
added the write memory barrier after ringing the doorbell register so
that controller sees the new request immediately.
Signed-off-by: NGilad Broner <gbroner@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In this change there are a few fixes of possible NULL pointer access and
possible access to index that exceeds array boundaries.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For small buffers we may use %*ph[N] specifier, for the bigger blocks
print_hex_dump() call.

Cc: Don Brace <don.brace@microsemi.com>
Cc: esc.storagedev@microsemi.com
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In kernel we have defined specifier (%*ph[C]) to dump small buffers in a
hex format. Replace custom approach by a generic one.

Cc: Jon Mason <jonmason@broadcom.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We have table of the HEX characters in the kernel. Replace custom by a
generic one.

Cc: Adaptec OEM Raid Solutions <aacraid@adaptec.com>
Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In the kernel we have nice specifier to print MAC by given pointer to
the address in a binary form.
Signed-off-by: NOleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com>
Acked-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

LAN MAC addresses can be printed directly using %pMR specifier.

Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instead of supplying each byte through stack let's use %pM specifier.

Cc: Hiral Patel <hiralpat@cisco.com>
Cc: Suma Ramars <sramars@cisco.com>
Acked-by: NTom Tucker <tom@opengridcomputing.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch addresses the issue of driver firing DCMDs in PCI
shutdown/detach path irrespective of firmware state.  Driver will now
check whether firmware is in operational state or not before firing
DCMDs. If firmware is in unrecoverable state or does not become
operational within specfied time, driver will skip firing DCMDs.

[mkp: fixed typos]
Signed-off-by: NSumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: NShivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch fixes the issue of wrong PhysArm was sent to firmware for R1
VD downgrade.
Signed-off-by: NKiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: NSumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For SRIOV enabled firmware, if there is a OCR(online controller reset)
possibility driver set the convert flag to 1, which is not happening if
there are outstanding commands even after 180 seconds.  As driver does
not set convert flag to 1 and still making the OCR to run, VF(Virtual
function) driver is directly writing on to the register instead of
waiting for 30 seconds. Setting convert flag to 1 will cause VF driver
will wait for 30 secs before going for reset.

CC: stable@vger.kernel.org
Signed-off-by: NKiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: NSumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avago is now known as Broadcom. Revise the emails and website for lpfc
accordingly.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The ->seq_release callback only ever had one implementation,
so call the function directly and drop the callback.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NJohannes Thumshirn <jth@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The ->seq_assign callback only ever had one implementation,
so call the function directly and drop the callback.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NJohannes Thumshirn <jth@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The ->seq_set_resp callback only ever had one implementation,
so call it directly and drop the callback.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NJohannes Thumshirn <jth@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The ->seq_start_next callback only ever had one implementation,
so call the function directly and drop the callback.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NJohannes Thumshirn <jth@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The ->exch_done callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NJohannes Thumshirn <jth@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The ->seq_exch_abort callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NJohannes Thumshirn <jth@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>