When a new LPM tree is created, we try to replace the trees in the
existing virtual routers with it. If we fail, the tree needs to be
freed.

Currently, this does not happen in the unlikely case where we fail to
bind the tree to the first virtual router, since its reference count
never transitions from 1 to 0.

Fix that by taking a reference before binding the tree.

Fixes: fc922bb0 ("mlxsw: spectrum_router: Use one LPM tree for all virtual routers")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A cleanup of the PM code left an incorrect #ifdef in place, leading
to a harmless build warning:

drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2502:12: error: 'fm10k_suspend' defined but not used [-Werror=unused-function]
drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2475:12: error: 'fm10k_resume' defined but not used [-Werror=unused-function]

It's easier to use __maybe_unused attributes here, since you
can't pick the wrong one.

Fixes: 8249c47c ("fm10k: use generic PM hooks instead of legacy PCIe power hooks")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the receive queue for 4096 bytes fragments, the page address
set in the SW data0 field of the descriptor is not the one we got
when doing the reassembly in receive. The page structure was retrieved
from the wrong descriptor into SW data0 which is then causing a
page fault when UDP checksum is accessing data above 1500.
Signed-off-by: NRex Chang <rchang@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of TX timeout, fs_timeout() calls phy_stop(), which
triggers the following BUG_ON() as we are in interrupt.

[92708.199889] kernel BUG at drivers/net/phy/mdio_bus.c:482!
[92708.204985] Oops: Exception in kernel mode, sig: 5 [#1]
[92708.210119] PREEMPT
[92708.212107] CMPC885
[92708.214216] CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G        W       4.9.61 #39
[92708.223227] task: c60f0a40 task.stack: c6104000
[92708.227697] NIP: c02a84bc LR: c02a947c CTR: c02a93d8
[92708.232614] REGS: c6105c70 TRAP: 0700   Tainted: G        W        (4.9.61)
[92708.241193] MSR: 00021032 <ME,IR,DR,RI>[92708.244818]   CR: 24000822  XER: 20000000
[92708.248767]
GPR00: c02a947c c6105d20 c60f0a40 c62b4c00 00000005 0000001f c069aad8 0001a688
GPR08: 00000007 00000100 c02a93d8 00000000 000005fc 00000000 c6213240 c06338e4
GPR16: 00000001 c06330d4 c0633094 00000000 c0680000 c6104000 c6104000 00000000
GPR24: 00000200 00000000 ffffffff 00000004 00000078 00009032 00000000 c62b4c00
NIP [c02a84bc] mdiobus_read+0x20/0x74
[92708.281517] LR [c02a947c] kszphy_config_intr+0xa4/0xc4
[92708.286547] Call Trace:
[92708.288980] [c6105d20] [c6104000] 0xc6104000 (unreliable)
[92708.294339] [c6105d40] [c02a947c] kszphy_config_intr+0xa4/0xc4
[92708.300098] [c6105d50] [c02a5330] phy_stop+0x60/0x9c
[92708.305007] [c6105d60] [c02c84d0] fs_timeout+0xdc/0x110
[92708.310197] [c6105d80] [c035cd48] dev_watchdog+0x268/0x2a0
[92708.315593] [c6105db0] [c0060288] call_timer_fn+0x34/0x17c
[92708.321014] [c6105dd0] [c00605f0] run_timer_softirq+0x21c/0x2e4
[92708.326887] [c6105e50] [c001e19c] __do_softirq+0xf4/0x2f4
[92708.332207] [c6105eb0] [c001e3c8] run_ksoftirqd+0x2c/0x40
[92708.337560] [c6105ec0] [c003b420] smpboot_thread_fn+0x1f0/0x258
[92708.343405] [c6105ef0] [c003745c] kthread+0xbc/0xd0
[92708.348217] [c6105f40] [c000c400] ret_from_kernel_thread+0x5c/0x64
[92708.354275] Instruction dump:
[92708.357207] 7c0803a6 bbc10018 38210020 4e800020 7c0802a6 9421ffe0 54290024 bfc10018
[92708.364865] 90010024 7c7f1b78 81290008 552902ee <0f090000> 3bc3002c 7fc3f378 90810008
[92708.372711] ---[ end trace 42b05441616fafd7 ]---

This patch moves fs_timeout() actions into an async worker.

Fixes: commit 48257c4f ("Add fs_enet ethernet network driver, for several embedded platforms")
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to check if p_ent->comp_mode is QED_SPQ_MODE_EBLOCK before
calling qed_spq_add_entry().  The test is fine is the mode is EBLOCK,
but if it isn't then qed_spq_add_entry() might kfree(p_ent).
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sts variable is holding link speed as well as state.  We should
be using ls to index into ls_to_ethtool.

Fixes: 265aeb51 ("nfp: add support for .get_link_ksettings()")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to architecture limitations, the IBM VNIC client driver is unable
to perform MAC address changes unless the device has "logged in" to
its backing device. Currently, pending MAC changes are handled before
login, resulting in an error and failure to change the MAC address.
Moving that chunk to the end of the ibmvnic_login function, when we are
sure that it was successful, fixes that.

The MAC address can be changed when the device is up or down, so
only check if the device is in a "PROBED" state before setting the
MAC address.

Fixes: c26eba03 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ARSTR  is always located at the start of the TSU register region, thus
using add_reg()  instead of add_tsu_reg() in __sh_eth_get_regs() to dump it
causes EDMR or EDSR (depending on the register layout) to be dumped instead
of ARSTR.  Use the correct condition/macro there...

Fixes: 6b4b4fea ("sh_eth: Implement ethtool register dump operations")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver lacks a MODULE_LICENSE tag, leading to a Kbuild warning:

WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/cirrus/cs89x0.o

This adds license, author, and description according to the
comment block at the start of the file.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To avoid configuration override, timestamp set call will
be moved from the netdevice open flow to the init flow.
By this, a close-open procedure will not override the timestamp
configuration.
In addition, the change will rename mlx5e_timestamp_set function
to be mlx5e_timestamp_init.

Fixes: ef9814de ("net/mlx5e: Add HW timestamping (TS) support")
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

PPS event did not update ptp_clock_event fields, therefore,
timestamp value was not updated correctly. This fix updates the
event source and the timestamp value for each PPS event.

Fixes: 7c39afb3 ("net/mlx5: PTP code migration to driver core section")
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Reported-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Set features function sets dev->features in order to keep track of which
features were successfully changed and which weren't (in case the user
asks for more than one change in a single command).

This breaks the logic in __netdev_update_features which assumes that
dev->features is not changed on success and checks for diffs between
features and dev->features (diffs that might not exist at this point
because of the driver override).

The solution is to keep track of successful/failed feature changes and
assign them to dev->features in case of failure only.

Fixes: 0e405443 ("net/mlx5e: Improve set features ndo resiliency")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Should not do the following swap between TCs 0 and 1
when max num of TCs is 1:
tclass[prio=0]=1, tclass[prio=1]=0, tclass[prio=i]=i (for i>1)

Fixes: 08fb1dac ("net/mlx5e: Support DCBNL IEEE ETS")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

ETS initialization might fail, add a print to indicate
such failures.

Fixes: 08fb1dac ("net/mlx5e: Support DCBNL IEEE ETS")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

ethtool statistics should be updated even when the interface is down
since it shows more than just netdev counters, which might change while
the logical link is down.
One useful use case, for example, is when running RoCE traffic over the
interface (while the logical link is down, but physical link is up) and
examining rx_prioX_bytes.

Fixes: f62b8bb8 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

We didn't store the result of mlx5_init_once, due to that
mlx5_load_one returned success on error.  Fix that.

Fixes: 59211bd3 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Change mlx5_get_uars_page to return ERR_PTR in case of
allocation failure. Change all callers accordingly to
check the IS_ERR(ptr) instead of NULL.

Fixes: 59211bd3 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix a memory leak where in case that pci_alloc_irq_vectors failed,
priv->irq_info was not released.

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: NAlaa Hleihel <alaa@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

There are systems platform information management interfaces (such as
HOST2BMC) for which we cannot disable local loopback multicast traffic.

Separate disable_local_lb_mc and disable_local_lb_uc capability bits so
driver will not disable multicast loopback traffic if not supported.
(It is expected that Firmware will not set disable_local_lb_mc if
HOST2BMC is running for example.)

Function mlx5_nic_vport_update_local_lb will do best effort to
disable/enable UC/MC loopback traffic and return success only in case it
succeeded to changed all allowed by Firmware.

Adapt mlx5_ib and mlx5e to support the new cap bits.

Fixes: 2c43c5a0 ("net/mlx5e: Enable local loopback in loopback selftest")
Fixes: c85023e1 ("IB/mlx5: Add raw ethernet local loopback support")
Fixes: bded747b ("net/mlx5: Add raw ethernet local loopback firmware command")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Resolve the sparse warning:
"sparse: Variable length array is used."
Use 2 arrays for 2 PRM register accesses.

Fixes: 96f17e07 ("mlxsw: spectrum: Support RED qdisc offload")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After performing reset driver polls on HW indication until learning
that the reset is done, but immediately after reset the device becomes
unresponsive which might lead to completion timeout on the first read.

Wait for 100ms before starting the polling.

Fixes: 233fa44b ("mlxsw: pci: Implement reset done check")
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link state and exception interrupts may be masked when we probe.
The firmware should in theory prevent sending (and automasking) those
interrupts if the device is disabled, but if my reading of the FW code
is correct there are firmwares out there with race conditions in this
area.  The interrupt may also be masked if previous driver which used
the device was malfunctioning and we didn't load the FW (there is no
other good way to comprehensively reset the PF).

Note that FW unmasks the data interrupts by itself when vNIC is
enabled, such helpful operation is not performed for LSC/EXN interrupts.

Always unmask the auxiliary interrupts after request_irq().  On the
remove path add missing PCI write flush before free_irq().

Fixes: 4c352362 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The  TXALCR1 offsets are incorrect in the register offset tables, most
probably due to copy&paste error.  Luckily, the driver never uses this
register. :-)

Fixes: 4a55530f ("net: sh_eth: modify the definitions of register")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NVenkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

flow_type in HWRM_FLOW_ALLOC is not being populated correctly due to
incorrect passing of pointer and size of l3_mask argument of is_wildcard().
Fixed this.

Fixes: db1d36a2 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: NSunil Challa <sunilkumar.challa@broadcom.com>
Reviewed-by: NSathya Perla <sathya.perla@broadcom.com>
Reviewed-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Renesas  SH7757 has 2 Fast and 2 Gigabit Ether controllers, while the
'sh_eth' driver can only reset and initialize TSU of the first controller
pair. Shimoda-san tried to solve that adding the 'needs_init' member to the
'struct sh_eth_plat_data', however the platform code still never sets this
flag. I think  that we can infer this information from the 'devno' variable
(set  to 'platform_device::id') and reset/init the Ether controller pair
only for an even 'devno'; therefore 'sh_eth_plat_data::needs_init' can be
removed...

Fixes: 150647fb ("net: sh_eth: change the condition of initialization")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes in probe error path:
- Restore dev_id before failed_ioremap path.
  Fixes: ("net: fec: restore dev_id in the cases of probe error")
- Call of_node_put(phy_node) before failed_phy path.
  Fixes: ("net: fec: Support phys probed from devicetree and fixed-link")
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When switching  the driver to the managed device API,  I managed to break
the  case of a  dual Ether devices sharing a single TSU: the 2nd Ether port
wouldn't probe. Iwamatsu-san has tried to fix this but his patch was buggy
and he then dropped the ball...

The solution is to  limit calling devm_request_mem_region() to the first
of  the two  ports  sharing the same TSU, so devm_ioremap_resource() can't
be used anymore for the TSU resource...

Fixes: d5e07e69 ("sh_eth: use managed device API")
Reported-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note in the databook - Section 4.4 - EEE :
" The EEE feature is not supported when the MAC is configured to use the
TBI, RTBI, SMII, RMII or SGMII single PHY interface. Even if the MAC
supports multiple PHY interfaces, you should activate the EEE mode only
when the MAC is operating with GMII, MII, or RGMII interface."

Applying this restriction solves a stability issue observed on Amlogic
gxl platforms operating with RMII interface and the internal PHY.

Fixes: 83bf79b6 ("stmmac: disable at run-time the EEE if not supported")
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Tested-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A few spots in 3c59x missed calls to dma_mapping_error checks, casuing
WARN_ONS to trigger.  Clean those up.  While we're at it, refactor the
refill code a bit so that if skb allocation or dma mapping fails, we
recycle the existing buffer.  This prevents holes in the rx ring, and
makes for much simpler logic

Note: This is compile only tested.  Ted, if you could run this and
confirm that it continues to work properly, I would appreciate it, as I
currently don't have access to this hardware
Signed-off-by: NNeil Horman <nhorman@redhat.com>
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: tedheadster@gmail.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ENA admin command queue errors are not handled as part of ena_down().
As a result, in case of error admin queue transitions to non-running
state and aborts all subsequent commands including those coming from
ena_up(). Reset scheduled by the driver from the timer service
context would not proceed due to sharing rtnl with ena_up()/ena_down()
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under certain conditions MSI-X interrupt might arrive right after it
was unmasked in ena_up(). There is a chance it would be processed by
the driver before device ENA_FLAG_DEV_UP flag is set. In such a case
the interrupt is ignored.
ENA device operates in auto-masked mode, therefore ignoring
interrupt leaves it masked for good.
Moving unmask of interrupt to be the last step in ena_up().
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 96ac18f1 ("cxgb4: Add support for new flash parts")
removed initialization of adapter->params.sf_fw_start causing issues
while flashing firmware to card. We no longer need sf_fw_start
in adapter->params as we already have macros defined for FW flash
addresses.

Fixes: 96ac18f1 ("cxgb4: Add support for new flash parts")
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When filter configuration is not supported, drivers should return
-EOPNOTSUPP so the core can react correctly.

Fixes: 2f4b411a ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some circumstances, such as with bridging, it is possible that the
stack will add a devices own MAC address to its unicast address list.

If, later, the stack deletes this address, then the i40e driver will
receive a request to remove this address.

The driver stores its current MAC address as part of the MAC/VLAN hash
array, since it is convenient and matches exactly how the hardware
expects to be told which traffic to receive.

This causes a problem, since for more devices, the MAC address is stored
separately, and requests to delete a unicast address should not have the
ability to remove the filter for the MAC address.

Fix this by forcing a check on every address sync to ensure we do not
remove the device address.

There is a very narrow possibility of a race between .set_mac and
.set_rx_mode, if we don't change netdev->dev_addr before updating our
internal MAC list in .set_mac. This might be possible if .set_rx_mode is
going to remove MAC "XYZ" from the list, at the same time as .set_mac
changes our dev_addr to MAC "XYZ", we might possibly queue a delete,
then an add in .set_mac, then queue a delete in .set_rx_mode's
dev_uc_sync and then update netdev->dev_addr. We can avoid this by
moving the copy into dev_addr prior to the changes to the MAC filter
list.

A similar race on the other side does not cause problems, as if we're
changing our MAC form A to B, and we race with .set_rx_mode, it could
queue a delete from A, we'd update our address, and allow the delete.
This seems like a race, but in reality we're about to queue a delete of
A anyways, so it would not cause any issues.

A race in the initialization code is unlikely because the netdevice has
not yet been fully initialized and the stack should not be adding or
removing addresses yet.

Note that we don't (yet) need similar code for the VF driver because it
does not make use of __dev_uc_sync and __dev_mc_sync, but instead roles
its own method for handling updates to the MAC/VLAN list, which already
has code to protect against removal of the hardware address.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The original code for __i40e_chk_linearize didn't take into account the
fact that if a fragment is 16K in size or larger it has to be split over 2
descriptors and the smaller of those 2 descriptors will be on the trailing
edge of the transmit. As a result we can get into situations where we didn't
catch requests that could result in a Tx hang.

This patch takes care of that by subtracting the length of all but the
trailing edge of the stale fragment before we test for sum. By doing this
we can guarantee that we have all cases covered, including the case of a
fragment that spans multiple descriptors. We don't need to worry about
checking the inner portions of this since 12K is the maximum aligned DMA
size and that is larger than any MSS will ever be since the MTU limit for
jumbos is something on the order of 9K.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Defer probe if regulator is not ready. E.g. some regulator is fixed
regulator controlled by i2c expander gpio, the i2c device may be probed
after the driver, then it should handle the case of defer probe error.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The static variable dev_id always plus one before netdev registerred.
It should restore the dev_id value in the cases of probe error.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since UDP based filters are not supported via big buffer cloud
filters, remove UDP support.  Also change a few return types to
indicate unsupported vs invalid configuration.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>