Platforms may want to provide architecture-specific functionality when
a PCI device is doing a hibernate transition.  Add a weak symbol
pcibios_pm_ops that architectures can override to do so.

[bhelgaas: fold in return value checks from v2 patch]
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0.  If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.

Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.

To reduce overall code bloat, make the changes described above.
Tested-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NKevin Hilman <khilman@linaro.org>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

This is a fix for commit 7897e602 ("PCI: Disable Bus Master
unconditionally in pci_device_shutdown()").  Vivek reported that
with this commit, kexec failed because none of his SATA disks
came up.

A ->shutdown() callback might put the device in D3cold, which means config
space is no longer available.

[bhelgaas: changelog]
Link: https://lkml.org/lkml/2013/3/12/529Reported-and-Tested-by: NVivek Goyal <vgoyal@redhat.com>
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch clears pci_dev->state_saved at the beginning of suspending.
PCI config state may be saved long before that.  Some drivers call
pci_save_state() from the ->probe() callback to get snapshot of sane
configuration space to use in the ->slot_reset() callback.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> # add comment
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Commit b566a22c ("PCI: disable Bus Master on PCI device shutdown")
used pci_disable_device(), but that doesn't disable Bus Mastering
unconditionally; we allow nested enable/disable calls, and only the
last disable call actually does anything.

This uses pci_clear_master() to unconditionally clear the Bus Master
bit.

Matthew Garrett and Alan Cox said (see LKML link below) that clearing Bus
Master for all PCI devices may lead to unpredictable consequences: some
devices ignores this bit and continue DMA, some of them hang after that or
crash the whole system.  But we're already trying to clear Bus Master in
general because of b566a22c; this merely deals with the cases where
drivers haven't shut down the device correctly.

[bhelgaas: changelog]
Link: https://lkml.org/lkml/2012/6/6/278Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

We want to add PCI devices to the device tree as early as possible but
delay attaching drivers.

device_add() adds a device to the device hierarchy and (via
device_attach()) attaches a matching driver and calls its .probe() method.
We want to separate adding the device to the hierarchy from attaching the
driver.

This patch does that by adding "match_driver" in struct pci_dev.  When
false, we return failure from pci_bus_match(), which makes device_attach()
believe there's no matching driver.

Later, we set "match_driver = true" and call device_attach() again, which
now attaches the driver and calls its .probe() method.

[bhelgaas: changelog, explicitly init dev->match_driver,
fold device_attach() call into pci_bus_add_device()]
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

For unbound PCI devices, what we need is:

 - Always in D0 state, because some devices do not work again after
   being put into D3 by the PCI bus.

 - In SUSPENDED state if allowed, so that the parent devices can still
   be put into low power state.

To satisfy these requirements, the runtime PM for the unbound PCI
devices are disabled and set to SUSPENDED state.  One issue of this
solution is that the PCI devices will be put into SUSPENDED state even
if the SUSPENDED state is forbidden via the sysfs interface
(.../power/control) of the device.  This is not an issue for most
devices, because most PCI devices are not used at all if unbound.
But there are exceptions.  For example, unbound VGA card can be used
for display, but suspending its parents makes it stop working.

To fix the issue, we keep the runtime PM enabled when the PCI devices
are unbound.  But the runtime PM callbacks will do nothing if the PCI
devices are unbound.  This way, we can put the PCI devices into
SUSPENDED state without putting the PCI devices into D3 state.

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=48201Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org          # v3.6+

With the demise of CONFIG_HOTPLUG as an option, the pci_uevent
function located in hotplug.c will now always be used and doesn't need
special treatment in the Makefile.  Move pci_uevent into pci-driver.c
and remove hotplug.c
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove conditional code based on CONFIG_HOTPLUG being false.  It's
always on now in preparation of it going away as an option.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the driver takes care of state saving, don't touch any registers on it.

Optimus (dual-gpu) laptops seem to have their own form of D3cold, but
unfortunately enter it on normal D3 transitions via the ACPI callback.

So when we use runtime PM to transition to D3, the card disappears off
the PCI bus, however we then try to access registers on it in the
runtime suspend finish, which really doesn't work.

This patch checks whether the pci state is saved and doesn't attempt to hit
any registers after that point if it is.

(Looks okay to Rafael)
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Some actions during shutdown need device to be in D0 state, such as
MSI shutdown etc, so resume device before shutdown.

Without this patch, a device may not be enumerated after a kexec
because the corresponding bridge is not in D0, so that
configuration space of the device is not accessible.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org		# v3.6+

This patch (as1591) moves the pm_runtime_get_noresume() and
pm_runtime_put_sync() calls from __device_suspend() and
device_resume() to device_prepare() and device_complete() in the PM
core.

The reason for doing this is to make sure that parent devices remain
at full power (i.e., don't go into runtime suspend) while their
children are being resumed from a system sleep.

The PCI core already contained equivalent code to serve the same
purpose.  The patch removes the duplicated code, since it is no longer
needed.  One of the comments from the PCI core gets moved into the PM
core, and a second comment is added to explain whe the _get_noresume
and _put_sync calls are present.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This patch removes hardcoded sysfs attributes manipulation and
converts them into generic pci_bus->drv_attrs. This saves several bytes.
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

This patch fixes the following bug:

http://marc.info/?l=linux-pci&m=134329923124234&w=2

The root cause of the bug is as follow.

If a device is not bound with the corresponding driver, the device
runtime PM will be disabled and the device will be put into suspended
state.  So that, the bridge/PCIe port connected to it may be put into
suspended and low power state.  When do probing for the device later,
because the bridge/PCIe port connected to it is in low power state,
the IO access to device may fail.

To solve the issue, the bridge/PCIe port connected to the device is
put into active state before probing.
Reported-by: NBjorn Mork <bjorn@mork.no>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NRafael J. Wysocki <rjw@sisk.pl>

Commit dbf0e4c7 (PCI: EHCI: fix crash during suspend on ASUS
computers) added a workaround for an ASUS suspend issue related to
USB EHCI and a bug in a number of ASUS BIOSes that attempt to shut
down the EHCI controller during system suspend if its PCI command
register doesn't contain 0 at that time.

It turns out that the same workaround is necessary in the analogous
hibernation code path, so add it.

References: https://bugzilla.kernel.org/show_bug.cgi?id=45811Reported-and-tested-by: NOleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org

Quite a few ASUS computers experience a nasty problem, related to the
EHCI controllers, when going into system suspend.  It was observed
that the problem didn't occur if the controllers were not put into the
D3 power state before starting the suspend, and commit
151b6128 (USB: EHCI: fix crash during
suspend on ASUS computers) was created to do this.

It turned out this approach messed up other computers that didn't have
the problem -- it prevented USB wakeup from working.  Consequently
commit c2fb8a3f (USB: add
NO_D3_DURING_SLEEP flag and revert 151b6128) was merged; it
reverted the earlier commit and added a whitelist of known good board
names.

Now we know the actual cause of the problem.  Thanks to AceLan Kao for
tracking it down.

According to him, an engineer at ASUS explained that some of their
BIOSes contain a bug that was added in an attempt to work around a
problem in early versions of Windows.  When the computer goes into S3
suspend, the BIOS tries to verify that the EHCI controllers were first
quiesced by the OS.  Nothing's wrong with this, but the BIOS does it
by checking that the PCI COMMAND registers contain 0 without checking
the controllers' power state.  If the register isn't 0, the BIOS
assumes the controller needs to be quiesced and tries to do so.  This
involves making various MMIO accesses to the controller, which don't
work very well if the controller is already in D3.  The end result is
a system hang or memory corruption.

Since the value in the PCI COMMAND register doesn't matter once the
controller has been suspended, and since the value will be restored
anyway when the controller is resumed, we can work around the BIOS bug
simply by setting the register to 0 during system suspend.  This patch
(as1590) does so and also reverts the second commit mentioned above,
which is now unnecessary.

In theory we could do this for every PCI device.  However to avoid
introducing new problems, the patch restricts itself to EHCI host
controllers.

Finally the affected systems can suspend with USB wakeup working
properly.

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=37632
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42728Based-on-patch-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NDâniel Fraga <fragabr@gmail.com>
Tested-by: NJavier Marcet <jmarcet@gmail.com>
Tested-by: NAndrey Rahmatullin <wrar@wrar.name>
Tested-by: NOleksij Rempel <bug-track@fisher-privat.net>
Tested-by: NPavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: stable <stable@vger.kernel.org>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit cc2893b6 (PCI: Ensure we re-enable devices on resume)
addressed the problem with USB not being powered after resume on
recent Lenovo machines, but it did that in a suboptimal way.
Namely, it should have changed the relevant code paths only,
which are pci_pm_resume_noirq() and pci_pm_restore_noirq() supposed
to restore the device's power and standard configuration registers
after system resume from suspend or hibernation.  Instead, however,
it modified pci_set_power_state() which is executed in several
other situations too.  That resulted in some undesirable effects,
like attempting to change a device's power state in the same way
multiple times in a row (up to as many as 4 times in a row in the
snd_hda_intel driver).

Fix the bug addressed by commit cc2893b6 in an alternative way,
by forcibly powering up all devices in pci_pm_default_resume_early(),
which is called by pci_pm_resume_noirq() and pci_pm_restore_noirq()
to restore the device's power and standard configuration registers,
and modifying pci_pm_runtime_resume() to avoid the forcible power-up
if not necessary.  Then, revert the changes made by commit cc2893b6
to make the confusion introduced by it go away.
Acked-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

This patch adds runtime D3cold support and corresponding ACPI platform
support.  This patch only enables runtime D3cold support; it does not
enable D3cold support during system suspend/hibernate.

D3cold is the deepest power saving state for a PCIe device, where its main
power is removed.  While it is in D3cold, you can't access the device at
all, not even its configuration space (which is still accessible in D3hot).
Therefore the PCI PM registers can not be used to transition into/out of
the D3cold state; that must be done by platform logic such as ACPI _PR3.

To support wakeup from D3cold, a system may provide auxiliary power, which
allows a device to request wakeup using a Beacon or the sideband WAKE#
signal.  WAKE# is usually connected to platform logic such as ACPI GPE.
This is quite different from other power saving states, where devices
request wakeup via a PME message on the PCIe link.

Some devices, such as those in plug-in slots, have no direct platform
logic.  For example, there is usually no ACPI _PR3 for them.  D3cold
support for these devices can be done via the PCIe Downstream Port leading
to the device.  When the PCIe port is powered on/off, the device is powered
on/off too.  Wakeup events from the device will be notified to the
corresponding PCIe port.

For more information about PCIe D3cold and corresponding ACPI support,
please refer to:

- PCI Express Base Specification Revision 2.0
- Advanced Configuration and Power Interface Specification Revision 5.0

[bhelgaas: changelog]
Reviewed-by: NRafael J. Wysocki <rjw@sisk.pl>
Originally-by: NZheng Yan <zheng.z.yan@intel.com>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Disable Bus Master bit on the device in pci_device_shutdown() to ensure PCI
devices do not continue to DMA data after shutdown.  This can cause memory
corruption in case of a kexec where the current kernel shuts down and
transfers control to a new kernel while a PCI device continues to DMA to
memory that does not belong to it any more in the new kernel.

I have tested this code on two laptops, two workstations and a 16-socket
server.  kexec worked correctly on all of them.
Signed-off-by: NKhalid Aziz <khalid.aziz@hp.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

If a PCI device is enabled to generate wakeup signals (PME) when put
into a low-power state by runtime PM, it will be still enabled to
generate those signals after the system shutdown, unless its driver's
.shutdown() callback takes care of the wakeup signals generation
setting.  Moreover, there are devices that are not enabled to wake
up the system and that are configured by runtime PM to generate
wakeup signals so that (runtime) remote wakeup works with them.
Those devices should be reconfigured during system shutdown so that
they don't generate wakeup signals, but at least some drivers don't
do that.  However, that very well may be done by the PCI core so
that drivers don't have to worry about it.  For this reason, modify
pci_device_shutdown() to disable the generation of wakeup events for
devices not supposed to wake up the system.

References: https://bugzilla.kernel.org/show_bug.cgi?id=37952Reported-and-tested-by: NKamil Iskra <kamil.54002@iskra.name>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch (as1514) cleans up some places where new_id and remove_id
sysfs attributes are created and deleted.  Handling both attributes in
a single routine rather than a pair of routines makes the code
smaller.  It also prevents certain kinds of errors, like one we
currently have in the USB subsystem: The removeid attribute is often
created even when newid isn't (because the driver's no_dynamid_id flag
is set).

In the case of the PCMCIA subsystem, the newid attribute is created
but never explicitly deleted.  The patch adds a deletion routine.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As part of the removal of get_driver()/put_driver(), this patch
(as1511) changes all the places that add dynamic IDs for drivers.
Since these additions are done by writing to the drivers' sysfs
attribute files, and the attributes are removed when the drivers are
unregistered, there is no reason to take an extra reference to the
drivers.

The one exception is the pci-stub driver, which calls pci_add_dynid()
as part of its registration.  But again, there's no reason to take an
extra reference here, because the driver can't be unloaded while it is
being registered.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Include the driver name and device in warning when a pci driver
supports both legacy pm and new framework as just the stack trace
gives no way to identify the driver.
Signed-off-by: NDavid Fries <David@Fries.net>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

A subsequent patch is going to move the invocation of
pm_runtime_barrier() from dpm_prepare() to __device_suspend().
Consequently, early wakeup events resulting from runtime resume
requests for wakeup devices queued up right before system suspend
will only be detected after all of the subsystem-level .prepare()
callbacks have run.  However, the PCI bus type calls
pm_runtime_get_sync() from its pci_pm_prepare() callback routine,
so it would destroy the early wakeup events information regarding PCI
devices.  To prevent this from happening add an early wakeup
detection mechanism, analogous to the one currently in dpm_prepare(),
to pci_pm_prepare().
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>

After commit e8665002
(PM: Allow pm_runtime_suspend() to succeed during system suspend) it
is possible that a device resumed by the pm_runtime_resume(dev) in
pci_pm_prepare() will be suspended immediately from a work item,
timer function or otherwise, defeating the very purpose of calling
pm_runtime_resume(dev) from there.  To prevent that from happening
it is necessary to increment the runtime PM usage counter of the
device by replacing pm_runtime_resume() with pm_runtime_get_sync().
Moreover, the incremented runtime PM usage counter has to be
decremented by the corresponding pci_pm_complete(), via
pm_runtime_put_sync().
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Xen save/restore is going to use hibernate device callbacks for
quiescing devices and putting them back to normal operations and it
would need to select CONFIG_HIBERNATION for this purpose.  However,
that also would cause the hibernate interfaces for user space to be
enabled, which might confuse user space, because the Xen kernels
don't support hibernation.  Moreover, it would be wasteful, as it
would make the Xen kernels include a substantial amount of code that
they would never use.

To address this issue introduce new power management Kconfig option
CONFIG_HIBERNATE_CALLBACKS, such that it will only select the code
that is necessary for the hibernate device callbacks to work and make
CONFIG_HIBERNATION select it.  Then, Xen save/restore will be able to
select CONFIG_HIBERNATE_CALLBACKS without dragging the entire
hibernate code along with it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Tested-by: NShriram Rajagopalan <rshriram@cs.ubc.ca>

After redefining CONFIG_PM to depend on (CONFIG_PM_SLEEP ||
CONFIG_PM_RUNTIME) the CONFIG_PM_OPS option is redundant and can be
replaced with CONFIG_PM.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Fix kernel-doc warning for __pci_device_probe():

Warning(drivers/pci/pci-driver.c:341): missing initial short description on line:
 * __pci_device_probe()
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value.  Also, a large majority of the callers do
not check the return code of pci_restore_state.  Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch (as1388) changes the way the PCI core handles runtime PM
settings when probing or unbinding drivers.  Now the core will make
sure the device is enabled for runtime PM, with a usage count >= 1,
when a driver is probed.  It does the same when calling a driver's
remove method.

If the driver wants to use runtime PM, all it has to do is call
pm_runtime_pu_noidle() near the end of its probe routine (to cancel
the core's usage increment) and pm_runtime_get_noresume() near the
start of its remove routine (to restore the usage count).  It does not
need to mess around with setting the runtime state to enabled,
disabled, active, or suspended.

The patch updates e1000e and r8169, the only PCI drivers that already
use the existing runtime PM interface.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Introduce run-time PM callbacks for the PCI bus type.  Make the new
callbacks work in analogy with the existing system sleep PM
callbacks, so that the drivers already converted to struct dev_pm_ops
can use their suspend and resume routines for run-time PM without
modifications.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some PCI devices fail if their standard configuration registers are
restored twice in a row.  Prevent this from happening by making
pci_restore_state() clear the saved_state flag of the device right
after the device's standard configuration registers have been
populated with the previously saved values.

Simplify PCI PM callbacks by removing the direct clearing of
state_saved from them, as it shouldn't be necessary any more (except
in pci_pm_thaw(), where it has to be cleared, so that the values saved
during the "freeze" phase of hibernation are not used later by mistake).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Currently pci_pm_resume() always returns 0, which makes the error
variable defined in there a bit pointless.  Make pci_pm_resume()
return error codes obtained from drivers' callbacks.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Separate out pci_add_dynid() from store_new_id() and export it so that
in-kernel code can add PCI IDs dynamically.  As the function will be
available regardless of HOTPLUG, put it and pull pci_free_dynids()
outside of CONFIG_HOTPLUG.

This will be used by pci-stub to initialize initial IDs via module
param.

While at it, remove bogus get_driver() failure check.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.

Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NAlek Du <alek.du@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

They are not supposed to be modified by drivers, so make them const.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

They are not supposed to be modified by drivers, so make them const.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

At present the configuration spaces of PCI devices that have no
drivers or no PM support in the drivers (either legacy or through a
pm object) are not saved during suspend and, consequently, they are
not restored during resume.  This generally may lead to the state of
the system being slightly inconsistent after the resume, so it's
better to save and restore the configuration spaces of these devices
as well.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Once we have allowed timer interrupts to be enabled during the late
phase of suspending devices, we are now able to use the generic
pci_set_power_state() to put PCI devices into low power states at
that time.  We can also use some related platform callbacks, like the
ones preparing devices for wake-up, during the late suspend.

Doing this will allow us to avoid the race condition where a device
using shared interrupts is put into a low power state with interrupts
enabled and then an interrupt (for another device) comes in and
confuses its driver.  At the same time, devices that don't support
the native PCI PM or that require some additional, platform-specific
operations to be carried out to put them into low power states will
be handled as appropriate.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Move pci_restore_standard_config() from pci.c to pci-driver.c and
make it static.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>