The current settings which can be used with the WM831x current sinks
can't easily be mapped between register values and currents at run
time without a lookup table since the values scale logarithmically
to match the way the human eye interprets brightness. This lookup
table is inclided in the core since several drivers need to use it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of devices use OTP (One Time Programmable, a type
of PROM) to store system configuration. At run time this data is
visible via registers.

Currently the only explicitly supported feature is that the unique
ID provided by every WM831x device is exported to user space via
sysfs. Other configuration data may be read by system-specific
code in the pre_init() and post_init() platform data operations.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x backlight driver requires at least the specification of the
current sink to use and a maximum current to allow them to function and
will actively interfere with other users of the regulators it uses if
misconfigured so only register the subdevice for it if this platform
data has been supplied.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x contains an auxiliary ADC with a number of switchable
inputs which is used to monitor some of the voltages and
temperatures in the system and has some external inputs which can be
used for machine specific purposes. Provide an API allowing drivers
to read values from the ADC.

An internal reference voltage is provided to allow callibration of
the ADC. This is used to calibrate the device at startup.

The hardware also supports continuous readings and digital comparators.
These are not yet supported by the driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x includes an interrupt controller managing interrupts for
the various functions on the chip. This patch adds support for the
core interrupt block on the device.

Ideally this would be supported by genirq, particularly for the
GPIOs, but currently genirq is unable to cope with controllers on
interrupt driven buses so we cut'n'paste the generic interface.
Once genirq is able to cope chips like this it should be a case
of filing the prefixes off the code and redoing wm831x-irq.c to
move over.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM831x series of devices are register compatible processor power
management subsystems, providing regulator and power path management
facilities along with other services like watchdog, RTC and touch
panel controllers.

This patch adds very basic support, providing basic single register
I2C access, handling of the security key and registration of the
devices.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Provide basic support for MFDs having multiple cells of a given
type with different IDs by adding an id to the mfd_cell structure
and then adding that to the id passed in to mfd_add_devices().

As it stands this approach requires that MFDs using this feature
deal with ensuring that there aren't any ID collisions resulting
from multiple MFDs of the same type being instantiated. This needs
to happen with the existing code too, but with this approach there
is a knock on effect on the IDs for non-duplicated devices.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Vibrator will be accessed via the pcap-regulator driver, no need to expose its
bits in the header file.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The 10 bits definition was the 8 bits one.
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Using the default kernel "events" workqueue causes problems with
synchronous adc readings if initiated from some task on the same
workqueue.

I had a deadlock trying to use pcf50633_adc_sync_read from a
power_supply class driver because the reading was initiated from the
workqueue and it waited for the irq processing to complete (to get the
result) and that was put on the same workqueue.
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Provides an atomic set_bits functions, as needed by the pcap-regulator
driver.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some TS controller bits are on the same register as the ADC control, save
TS specific bits and export a set_ts_bits function so the TS driver can set
it with the adc_mutex lock held.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Export an irq_to_pcap function to get pcap irq number, for the keypad driver.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

We can not have .driver_data as const since platform_set_drvdata() doesnt take
a const.
The hclk mmc_data field can be const though.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Only the base addresses remain, as they are needed to set up
the IOMEM resources.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

IRQ number definitions for PWM, LED, SPI and OWM (ds1wm).
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Used to configure single bits of the SDHWCTRL_SDCONF and EXTCF_RESET/SELECT
registers needed for DS1WM, MMC/SDIO and PCMCIA functionality.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The PCAP Asic as present on EZX phones is a multi function device with
voltage regulators, ADC, touch screen controller, RTC, USB transceiver,
leds controller, and audio codec.

It has two SPI ports, typically one is connected to the application
processor and another to the baseband, this driver provides read/write
functions to its registers, irq demultiplexer and ADC
queueing/abstraction.

This chip is used on a lot of Motorola phones, it was manufactured by TI
as a custom product with the name PTWL93017, later this design evolved
into the ATLAS PMIC from Freescale (MC13783).
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds a core driver for the AB3100 mixed-signal circuit
found in the ST-Ericsson U300 series platforms. This driver
is a singleton proxy for all accesses to the AB3100
sub-drivers which will be merged on top of this one, RTC,
regulators, battery and system power control, vibrator,
LEDs, and an ALSA codec.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Reviewed-by: NMike Rapoport <mike@compulab.co.il>
Reviewed-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Acked-by: NSamuel Ortiz <sameo@openedhand.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

This driver requests a clock that usually is supplied by the MFD in which
the DS1WM is contained. Currently, it is impossible for a MFD to register
their clocks with the generic clock API due to different implementations
across architectures.
For now, this patch removes the clock handling from DS1WM altogether,
trusting that the MFD enable/disable functions will switch the clock if
needed. The clock rate is obtained from a new parameter in driver_data.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

Removes the now-unused bus_shift field from pasic3_platform_data.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

This patch converts the DS1WM driver into an MFD cell. It also
calculates the bus_shift parameter from the memory resource size.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

The WM8400 is a highly integrated audio CODEC and power management unit
intended for mobile multimedia application.  This driver supports the
primary audio CODEC features, including:

 - 1W speaker driver
 - Fully differential headphone output
 - Up to 4 differential microphone inputs
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The 'pcf50633_mbc_set_status' function is unused, so remove it.
Signed-off-by: NBalaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

The battery charger state machine switches into charging mode when
the battery voltage falls below 96% of a battery float voltage. But
the voltage drop in Li-ion batteries is marginal(1~2 %) till about
80% of its capacity - which means, after a BATFULL, charging won't
be restarted until 80%.

This work_struct function restarts charging at regular intervals to
make sure the battery doesn't discharge too much.
Signed-off-by: NBalaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Changes from V1:
	- Removed support for suspend_enable & suspend_disable functions.
Signed-off-by: NBalaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

Signed-off-by: NBalaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

What the PCF05633 calls as a 'GPIO' is much more than the GPIO in the linux
sense and there are only 4 of them - which means, the gpiolib is not used
here.
Signed-off-by: NBalaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

This patch adds basic support for the PCF50633 ADC. The subtractive mode
is not supported yet.

Since we don't have adc subsystem, it currently lives in drivers/mfd.
Signed-off-by: NBalaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Acked-by: NJonathan Cameron <jonathan.cameron@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

This patch implements the core of the PCF50633 driver. This core driver has
generic register read/write functions and does interrupt management for its
sub devices.
Signed-off-by: NBalaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The voltage and current regulators on the WM8350 AudioPlus PMIC can be
used in concert to provide a power efficient LED driver.  This driver
implements support for this within the standard LED class.

Platform initialisation code should configure the LED hardware in the
init callback provided by the WM8350 core driver.  The callback should
use wm8350_isink_set_flash(), wm8350_dcdc25_set_mode() and
wm8350_dcdc_set_slot() to configure the operating parameters of the
regulators for their hardware and then then use wm8350_register_led() to
instantiate the LED driver.

This driver was originally written by Liam Girdwood, though it has been
extensively modified since then.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The WM8351 is a WM8350 variant. As well as register default changes the
WM8351 has fewer voltage and current regulators than the WM8350.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

Some WM8350 variants have fewer DCDCs and ISINKs. Identify these at
probe and refuse to use the absent DCDCs when running on these chips.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

The WM8352 is a variant of the WM8350. Aside from the register defaults
there are no software visible differences to the WM8350.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

This patch amends DA903x MFD driver with definitions and methods
needed for battery charger driver.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

Implement support for reporting battery health in the WM8350 battery
interface. Since we are now able to report this via the classs remove
the diagnostics from the interrupt handler.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>