Add a sysdev for DBDMA PM.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1119/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use a sysdev to implement PM methods for the Au1000 interrupt controllers.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1114/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Clean out stray unused board_reset() calls in pb1x boards, the PB1000 is
different from the rest and gets private methods.

(Cleanup after 32fd6901)
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1085/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Same issues as SD card detection:  One of both is always triggering and the
handlers take care to shut it up and enable the other.  To avoid messages
about "unbalanced interrupt enable/disable" they must not be automatically
enabled when initally requested.

This was not an issue with the db1200_defconfig due to fortunate timings;
on a build without network chip support the warnings appear.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1133/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

While playing with the out-of-tree MAE driver module, the system would
panic after a while in the db1200 custom wait code after wakeup due to
a clobbered k0 register being used as target address of a store op.

Remove the custom wait implementation and revert back to the Alchemy-
recommended implementation already set as default.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1092/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Don't define platform info for second mac on au1100 (which only has a
single mac).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1004/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

A few hunks somehow ended up outside their #ifdef/endif blocks,
leading to -Werror-induces build failures.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1003/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On Alchemy the PCMCIA area lies at the end of the chips 36bit system bus
area.  Currently, addresses at the far end of the 32bit area are assumed
to belong to the PCMCIA area and fixed up to the real 36bit address before
being passed to ioremap().

A previous commit enabled 64 bit physical size for the resource datatype on
Alchemy and this allows to use the correct 36bit addresses when registering
the PCMCIA sockets.

This patch removes the 32-to-36bit address fixup and registers the Alchemy
demo board pcmcia socket with the correct 36bit physical addresses.

Tested on DB1200, with a CF card (ide-cs driver) and a 3c589 PCMCIA ethernet
card.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/994/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Save/restore CPLD registers when doing suspend-to-ram; this fixes issues
with harddisk and ethernet not working correctly when resuming on DB1200.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/986/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>

The sole user is au1xxx_calc_clock() which is only used in early bootup
where the is no paralellism thus no race condition to protect against.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>

Signed-off-by: NFrans Pop <elendil@planet.nl>
To: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/946/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/928/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/927/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It is not always used, even if it is available.
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/893/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Implement reset / poweroff in the board code instead.  The peripheral reset
code is gone too since YAMON which all in-tree boards use does the same
work when it boots.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/783/
Patchwork: http://patchwork.linux-mips.org/patch/882/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use runtime CPU detection instead of relying on preprocessor symbols.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/701/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use the GPIO config symbol to only build Au1000 interrupt code on chips with
compatible hw.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/670/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove the cpu subtype cpp macros in favor of runtime detection,
to improve compile coverage of the alchemy common code.
(Increases kernel size by 700 bytes).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/699/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch makes the board code register the au1000-eth platform device. The
au1000-eth platform data can be overriden with the au1xxx_override_eth_cfg
function like it has to be done for the Bosporus board which uses a
different MAC/PHY setup.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Cc: David Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/618/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Machine driver for DB1200 AC97 and I2S audio systems, intended as a proper
reference asoc machine for Alchemy-based systems.  AC97/I2S can be selected
at boot time by setting switch S6.7.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: alsa-devel@alsa-project.org
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Create own directory for DB1200 code and update it with new features.

- SPI support:
  - tmp121 temperature sensor
  - SPI flash on DB1200
- I2C support
  - NE1619 sensor
  - AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Replace the devboard NOR MTD mapping driver with physmap-flash support.
Also honor the "swapboot" switch settings wrt. to the layout of the
NOR partitions.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Acked-By: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

UART autodetection breaks on the Au1300 but the IP blocks are identical,
at least according to the datasheets.  Help the 8250 driver by passing
on uart type information via platform data.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Warnings being suppressed, we can now turn on -Werror for boards which did
not have it already (devboards and xss1500).
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch fixes warnings due to potentially unused
variables in board setup code or mixed variables
declaration and code (forbidden by ISO C90).
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove unused uart bit definitions and base macros.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch replaces the general alchemy prom_putchar() implementation
in favor of board-specific versions:  The UART where the output of
prom_putchar is directed to really depends on the board, the current
implementation hardcodes this on a per-SoC basis which is just wrong.

So a generic uart tx function is provided in the alchemy headers,
and the boards can provide their own prom_putchar with custom
destination uart, and all in-kernel alchemy boards support
early printk.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.

(Queueing function signature has changed in order to give
 a build failure instead of silent functional changes due
 to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

By replacing an extra do_IRQ with a goto, the assembly shrinks
from 260 to 212 bytes (gcc-4.3.4).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Eliminate the sharing of IRQ names among the differenct Alchemy
variants.  IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.

This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!

Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.

Run-tested on DB1200.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Raise RTCMATCH2 interrupt priority in case it is used as the system
timer tick.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Alchemy hardware provides a method to prioritize interrupts
on a controller by assigning them to a differenct core request line.
Assign usb device request interrupt to IC0 Request 0 (which has
highest priority in the core and the dispatcher) and others to
Request 1.  The explicit check for usb device request occurrence
should be obsolete now.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Rewritten XXS1500 PCMCIA socket driver, standalone (doesn't depend on
au1000_generic.c) and added carddetect IRQ support.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
        - supports Db1000, DB/PB1100/1500/1550/1200.
        - support for carddetect and statuschange IRQs.
        - pcmcia socket mem/io/attr areas and irqs passed through
          platform resource information.
        - doesn't freeze system during card insertion/ejection like
          the one it replaces.
        - boardtype is automatically detected using BCSR ID register.

Run-tested on the DB1200.

Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

remove board_init_irq():  On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.

Some small irqmap.c files have been folded into board_setup files.

Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move the PB1200 IRQ cascade code out to the BCSR support code:
upcoming DB1300 support can use it too.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

All Alchemy development boards have external CPLDs with a few registers
in them.  They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.

This patch
- adds a primitive facility to initialize and use these external
  registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
  functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
  headers in a central place.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>