The current wl12xx fw (7.3.0.0.77) supports both STA and AP mode, and
we no longer use AP-mode-specific quirks.

WL12XX_QUIRK_END_OF_TRANSACTION is still used for certain HWs, while
WL12XX_QUIRK_LPD_MODE is not used anymore.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The wl12xx FW supports HW channel switch.  If we don't use it,
sometimes the firmware gets confused when recalibrating to the new
channel, causing RX problems.  This commit adds HW channel switch
support by implementing the channell_switch op.
Signed-off-by: NShahar Levi <shahar_levi@ti.com>
[added one comment, remove the tx_flush and rephrased the commit message]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The wiphy max_sched_scan_ie_len attribute was not set correctly and
remained as 0, so when IEs were being passed in a scheduled scan, we
were returning -EINVAL.

Fix this by setting the attribute properly.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

p2p packets should go out only with OFDM rates.

Configure a new rate policy that will (later) be used
during p2p_find (when the p2p_cli / p2p_go interfaces
are in use, we won't have to use this policy, as
the configured rates should already be OFDM-only).

Additionally, update CONF_TX_MAX_RATE_CLASSES to reflect
the current value from the fw api.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

the AR_SREV register does not seems to indicate whether AR9480 is
pci_express capable or not though the other information like macVersion
etc can be obtained properly. this fix is essential as ASPM won't be intialized
and its related driver functionality ath9k_hw_configpcipowersave won't be
called
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets

Cc: stable@kernel.org
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent patches added support for resetting the SD8686 hardware when
commands time out, which seems to happen quite frequently soon after
resuming the system from a Wake-on-WLAN-triggered resume.

At http://dev.laptop.org/ticket/10969 we see the same thing happen
with transmits. In this case, the hardware will fail to respond to
a frame passed for transmission, and libertas (correctly) will block
all further commands and transmissions as the hardware can only
deal with one thing at a time. This results in a lockup while the
system waits indefinitely for the dead card to respond.

Hook up a TX lockup timer to detect this and reset the hardware.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.

The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
	ops.conf_tx = conf_tx_op;

@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
	conf_tx_op (
-		struct ieee80211_hw *hw,
+		struct ieee80211_hw *hw, struct ieee80211_vif *vif,
		u16 queue,
		const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename the iwlagn module as iwlwifi in preparation for future
changes.  Add an alias to iwlagn for backward compatibility.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

this extends the bits for rf kill GPIO selection to [7:2] from [4:2] as
we use GPIO pin 11 as rfkill for AR9480 and also remove few unused
macros

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: "Hu, Russell" <rhu@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In failure case locks are not allocated in mwifiex_register().
So mwifiex_free_lock_list() routine call becomes redundant.
Also we don't need to check return type for mwifiex_init_lock_list()
routine. It never fails.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "mwifiex: remove list traversal.."(fcf2176c..)
wrongly modifies AMSDU aggregation check. Due to this even though
packet size for iperf traffic is already large, we unnecessarily
try to aggregate them which adds some delay. If Tx iperf is started
on UUT for 30 seconds, UUT keeps sending Tx packets for few more
seconds.

That commit is reverted to fix the problem.
Also, MIN_NUM_AMSDU check is moved inside the loop to optimize the
loop.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This was reported and tested by Martin Walter over at AVM GmbH Berlin.
This also applies to 3.0.1 so sendint to stable.

Cc: s.kirste@avm.de
Cc: d.friedel@avm.de
Cc: Martin Walter <m.walter@avm.de>
Cc: Peter Grabienski <pgrabien@qca.qualcomm.com>
Cc: stable@kernel.org
Tested-by: NMartin Walter <m.walter@avm.de>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recently mac80211 was changed to use nullfunc instead of probe
request for connection monitoring for tx ack status reporting
hardwares. Sometimes in congested network, STA got disconnected
quickly after the association. It was observered that the rate
control was not adopted to environment due to minimal transmission.

As the nullfunc are used for monitoring purpose, these frames should
not be sacrificed for rate control updation. So it is better to send
the monitoring null func frames at minimum rate that could help to
retain the connection.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a gpio setup function which gives a chance to set up
platform specific configuration such as pin multiplexing,
input/output direction at the runtime or booting time.
Signed-off-by: NSangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow injected unicast frames to be sent without having to wait
for an ACK.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes compilation errors when compiling for ARM:

ath6kl/debug.c:312: error: implicit declaration of function 'vmalloc'
ath6kl/debug.c:312: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:342: error: implicit declaration of function 'vfree'
ath6kl/debug.c:696: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:871: warning: assignment makes pointer from integer without a cast
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

My earlier debug log additions added these warnings when compiling 64 bit
kernels:

ath6kl/init.c:962: warning: format '%d' expects type 'int',
  but argument 3 has type 'size_t'
ath6kl/init.c:975: warning: format '%d' expects type 'int',
  but argument 3 has type 'size_t'
ath6kl/init.c:988: warning: format '%d' expects type 'int',
  but argument 3 has type 'size_t'
ath6kl/init.c:1009: warning: format '%d' expects type 'int',
  but argument 3 has type 'size_t'
ath6kl/init.c:1192: warning: format '%d' expects type 'int',
  but argument 4 has type 'size_t'
ath6kl/init.c:1236: warning: format '%d' expects type 'int',
  but argument 4 has type 'size_t'
ath6kl/init.c:1267: warning: format '%d' expects type 'int',
  but argument 4 has type 'size_t'
Reported-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

802.11 says:
"Sequence numbers for QoS (+)Null frames may be
set to any value."

However, if we use the normal counters then peers
will get confused with aggregation since there'll
be holes in the sequence number sequence.

To avoid that, neither assign a sequence number
to QoS null frames nor put them on aggregation.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the addition of uAPSD and driver buffering
the powersave handling has gotten quite complex.
Add a section to the documentation to explain it
for anyone wanting to implement it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwlwifi has a separate EOSP notification from
the device, and to make use of that properly
it needs to be passed to mac80211. To be able
to mix with tx_status_irqsafe and rx_irqsafe
it also needs to be an "_irqsafe" version in
the sense that it goes through the tasklet,
the actual flag clearing would be IRQ-safe
but doing it directly would cause reordering
issues.

This is needed in the case of a P2P GO going
into an absence period without transmitting
any frames that should be driver-released as
in this case there's no other way to inform
mac80211 that the service period ended. Note
that for drivers that don't use the _irqsafe
functions another version of this function
will be required.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwlwifi needs to know the number of frames that are
going to be sent to a station while it is asleep so
it can properly handle the uCode blocking of that
station.

Before uAPSD, we got by by telling the device that
a single frame was going to be released whenever we
encountered IEEE80211_TX_CTL_POLL_RESPONSE. With
uAPSD, however, that is no longer possible since
there could be more than a single frame.

To support this model, add a new callback to notify
drivers when frames are going to be released.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My work and some previous work didn't add
all the flags, add them now and while at it
simplify the code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.

The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.

On x86-64, this is a fairly significant code
size reduction:
   text	   data	    bss	    dec	    hex
 427861	  23648	   1008	 452517	  6e7a5	before
 425383	  23648	    976	 450007	  6ddd7	after
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a PS-poll frame is retried (but was received)
there is no way to detect that since it has no
sequence number. As a consequence, the standard
asks us to not react to PS-poll frames until the
response to one made it out (was ACKed or lost).

Implement this by using the WLAN_STA_SP flags to
also indicate a PS-Poll "service period" and the
IEEE80211_TX_STATUS_EOSP flag for the response
packet to indicate the end of the "SP" as usual.

We could use separate flags, but that will most
likely completely confuse drivers, and while the
standard doesn't exclude simultaneously polling
using uAPSD and PS-Poll, doing that seems quite
problematic.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For PS-poll, there's a possible race between
us expiring a frame and the station polling
for it -- send it a null frame in that case.

For uAPSD, the standard says that we have to
send a frame in each SP, so send null if we
don't have any other frames.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add uAPSD support to mac80211. This is probably not
possible with all devices, so advertising it with
the cfg80211 flag will be left up to drivers that
want it.

Due to my previous patches it is now a fairly
straight-forward extension. Drivers need to have
accurate TX status reporting for the EOSP frame.
For drivers that buffer themselves, the provided
APIs allow releasing the right number of frames,
but then drivers need to set EOSP and more-data
themselves. This is documented in more detail in
the new code itself.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If there are frames for a station buffered in
the driver, mac80211 announces those in the TIM
IE but there's no way to release them. Add new
API to release such frames and use it when the
station polls for a frame.

Since the API will soon also be used for uAPSD
it is easily extensible.

Note that before this change drivers announcing
driver-buffered frames in the TIM bit actually
will respond to a PS-Poll with a potentially
lower priority frame (if there are any frames
buffered in mac80211), after this patch a driver
that hasn't been changed will no longer respond
at all. This only affects ath9k, which will need
to be fixed to implement the new API.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It doesn't seem likely, but maybe possible, that the
more-data bit needs to be recomputed due to changes
in the queued frames. Clear it for filtered frames
to ensure that we never send it incorrectly. It'll
be set again as necessary when we retransmit this
frame.

The more likely case is maybe where the station woke
up after the filtered frame in which case more-data
should be clear when the frame is transmitted to the
station since it is now awake.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we no longer use the return value, we no
longer need to maintain it either, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For uAPSD support we'll need to have per-AC PS
buffers. As this is a major undertaking, split
the buffers before really adding support for
uAPSD. This already makes some reference to the
uapsd_queues variable, but for now that will
never be non-zero.

Since book-keeping is complicated, also change
the logic for keeping a maximum of frames only
and allow 64 frames per AC (up from 128 for a
station).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 will expire normal PS-buffered frames, but
if the device rejected some frames for a sleeping
station, these won't be on the ps_tx_buf queue but
on the tx_filtered queue instead; this is done to
avoid reordering.

However, mac80211 will not expire frames from the
filtered queue, let's fix that.

Also add a more comments to what all this expiry is
doing and how it works.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the TIM bit for a given station is set
and cleared all over the place. Since the logic to
set/clear it will become much more complex when we
add uAPSD support, as a first step let's collect
the entire logic in one place. This requires a few
small adjustments to other places.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For uAPSD implementation, it is necessary to know on
which ACs frames are buffered. mac80211 obviously
knows about the frames it has buffered itself, but
with aggregation many drivers buffer frames. Thus,
mac80211 needs to be informed about this.

For now, since we don't have APSD in any form, this
will unconditionally set the TIM bit for the station
but later with uAPSD only some ACs might cause the
TIM bit to be set.

ath9k is the only driver using this API and I only
modify it in the most basic way, it won't be able
to implement uAPSD with this yet. But it can't do
that anyway since there's no way to selectively
release frames to the peer yet.

Since drivers will buffer frames per TID, let them
inform mac80211 on a per TID basis, mac80211 will
then sort out the AC mapping itself.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.

During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.

When setup completes and the peer is authorized, send data directly,
bypassing the AP.

In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).

In addition, make sure all peers are removed on disassociation.

A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Register and implement the TDLS cfg80211 callback functions.

Internally prepare and send TDLS management frames. We incorporate
local STA capabilities and supported rates with extra IEs given by
usermode. The resulting packet is either encapsulated in a data frame,
or assembled as an action frame. It is transmitted either directly or
through the AP, as mandated by the TDLS specification.

Declare support for the TDLS external setup wiphy capability. This
tells usermode to handle link setup and discovery on its own, and use the
kernel driver for sending TDLS mgmt packets.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Relocate the mesh implementation of adding the (extended) supported
rates IE to util.c, anticipating its use by other parts of mac80211.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>