Merge boards together as they are barely the same.
Signed-off-by: NNico Erfurth <ne@erfurth.eu>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: updated to new machine_desc structure]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>

This adds support for the RSI EWS machine (at91rm9200-based),
machine type 1609.

Includes fixes as suggested by Uwe Kleine-König and
cleanups as suggested by Russell and R.Schwebel.
Signed-off-by: NJosef Holzmayr <holzmayr@rsi-elektrotechnik.de>
[nicolas.ferre@atmel.com: simplify board file header, move to at91_init_irq_default]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

In the p1023rds, a physical bus of nor flash is 16 bits width.
The bank-width is width (in bytes) of the bus width. So, the
value of bank-width of nor flash is not one, and it should be
two.
Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

corenet based SoCs have SEC4 h/w, so enable the SEC4 driver,
caam, and the algorithms it supports, and disable the
SEC2/3 driver, talitos.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable the audio drivers in the non-corenet 85xx defconfigs so that audio
is enabled on the Freescale P1022DS reference board.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These were missed in commit f5b94099 "All Arch: remove linkage
for sys_nfsservctl system call" due to them having no sys_ prefix
(presumably).

Cc: NeilBrown <neilb@suse.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NJames Bottomley <James.Bottomley@hansenpartnership.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On Sun4d systems running in SMP mode, IRQ 14 is used for timer interrupts
and has a specialized interrupt handler. IPI is currently set to use IRQ 14
as well, which causes it to trigger the timer interrupt handler, and not the
IPI interrupt handler.

The IPI interrupt is therefore changed to IRQ 13, which is the highest
normally handled interrupt. This IRQ is also used for SBUS interrupts,
however there is nothing in the IPI/SBUS interrupt handlers that indicate
that they will not handle sharing the interrupt.
(IRQ 13 is indicated as audio interrupt, which is unlikely to be found in a
sun4d system)
Signed-off-by: NKjetil Oftedal <oftedal@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add clock control support for sh7372 CMT hardware blocks.

No upstream sh7372 boards are making use of CMT3 + CMT4,
but the sh7372 hardware happens to come out of reset with
all CMT MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.

This patch relies on the recently merged

 794d78fe drivers: sh: late disabling of clocks V2

to make sure the unused clocks get disabled as expected.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add clock control support for sh7372 MSIOF hardware blocks.

No upstream sh7372 boards are making use of MSIOF0->2,
but the sh7372 hardware happens to come out of reset with
all MSIOF MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.

This patch relies on the recently merged

 794d78fe drivers: sh: late disabling of clocks V2

to make sure the unused clocks get disabled as expected.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

USB-DMAC1 needs SMSTPCR4/MSTP407 controls, not MSTP214
this patch tested on mackerel board
Reported-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

MAINCKSEL is [29:28], not [27:24]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes support for the SGX interrupt source in
the sh7372 INTCS controller.

The SGX hardware block included in sh7372 is already hooked
up to the ARM Cortex-A8 core using the INTCA controller,
so SGX users are encouraged to make use of that interrupt
source instead.

Removing support for the SGX interrupt source in INTCS
simplifies the sh7372 power management code by allowing
us to assume that only INTCA needs to be powered on to
operate the SGX hardware.

If the INTCS interrupt source would be kept then the kernel
would be forced to deal with additional dependencies that does
not follow the regular power domain hiearachy. With this
patch in place we can safely power down INTCS while the
SGX is operating.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix the following build errors:

  CC      arch/sh/kernel/cpu/sh4a/setup-sh7757.o
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:681: error: implicit declaration of function ‘DMA_BIT_MASK’
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:681: error: initializer element is not constant
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:681: error: (near initialization for ‘usb_ehci_device.dev.coherent_dma_mask’)
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:705: error: initializer element is not constant
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:705: error: (near initialization for ‘usb_ohci_device.dev.coherent_dma_mask’)
make[3]: *** [arch/sh/kernel/cpu/sh4a/setup-sh7757.o] Error 1
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds unaligned memory access support for the following instructions:
  mov.w @(disp,PC),Rn
  mov.l @(disp,PC),Rn

These instructions are often used on SH2A toolchains.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch just clears the return code for those cases where an
unaligned memory access occurs on branch instructions without a
delay slot.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

For ARMv7 kernels running in the non-secure world, writing to the
auxillary control register causes an abort, so we must avoid directly
writing the auxillary control register.  If the ACR has already been
reinitialized by SoC code, don't try to restore it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add a dsb after the isb to ensure that the previous writes to the
CP15 registers take effect before we enable the MMU.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ARM920 and ARM926 save four registers, not three.  Fix the size of
the suspend region required.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

r1 stores the v:p offset from the CPU invariant resume code, and is
expected to be preserved by the CPU specific code.  Overwriting it is
not a good idea.

We've managed to get away with it on sa1100 platforms because most
happen to have PHYS_OFFSET == PAGE_OFFSET, but that may not be the
case depending on kernel configuration.  So fix this latent bug.

This fixes xsc3 as well which was saving and restoring this register
independently.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

cpu_v7_reset disables the MMU and then branches to the provided address.
On Thumb-2 kernels, we should take care to clear the Thumb Exception
enable bit in the System Control Register, otherwise this may wreak
havok in the code to which we are branching (for example, an ARM kernel
image via kexec).
Reviewed-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 540b5738 ("ARM: 6999/1: head, zImage: Always Enter the kernel in
ARM state") mandates that the kernel should be entered in ARM state.

If a Thumb-2 kernel kexecs a new kernel image, we need to ensure that
we change state when branching to the new code. This patch replaces a
mov pc, lr with a bx lr on Thumb-2 kernels so that we transition to ARM
state if need be.
Reviewed-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
 - Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to the SFI specification irq number 0xFF means device has no
interrupt or interrupt attached via GPIO.

Currently, we don't handle this special case and set irq field in
*_board_info structs to 255.  It leads to confusion in some drivers.
Accelerometer driver tries to register interrupt 255, fails and prints
"Cannot get IRQ" to dmesg.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This bug causes the IECSR register clear failure.  In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared.  So the related ISR may be called persistently.

The RETE bit in IECSR is cleared by writing a 1 to it.
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following build errors:

  drivers/tty/serial/8250_early.c:160: error: 'BASE_BAUD' undeclared (first use in this function): 1 errors in 1 logs
  drivers/tty/serial/8250_early.c:37:24: error: asm/serial.h: No such file or directory: 1 errors in 1 logs

I am not sure if (1843200 / 16) is suitable for cris, but most other
arch's define it as this value.
Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The bug was accidentally found by the following program:

    #include <asm/sysinfo.h>
    #include <asm/unistd.h>
    #include <sys/syscall.h>
    static int setsysinfo(unsigned long op, void *buffer, unsigned long size,
                          int *start, void *arg, unsigned long flag) {
        return syscall(__NR_osf_setsysinfo, op, buffer, size, start, arg, flag);
    }

    int main(int argc, char **argv) {
        short x[10];
        unsigned int buf[2] = { SSIN_UACPROC, UAC_SIGBUS, };
        setsysinfo(SSI_NVPAIRS, buf, 1, 0, 0, 0);

        int  *y = (int*) (x+1);
        *y = 0;
        return 0;
    }

The program shoud fail on SIGBUS, but didn't.

The patch is a second part of userspace flag fix (commit 745dd240
"Alpha: Rearrange thread info flags fixing two regressions").

Deleted outdated out-of-sync 'UAC_SHIFT' (the cause of bug) in favour of
'ALPHA_UAC_SHIFT'.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NSergei Trofimovich <slyfox@gentoo.org>
Acked-by: NMichael Cree <mcree@orcon.net.nz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

entry_32.S contained a hardcoded alternative instruction entry, and the
format changed in commit 59e97e4d ("x86: Make alternative
instruction pointers relative").

Replace the hardcoded entry with the altinstruction_entry macro.  This
fixes the 32-bit boot with CONFIG_X86_INVD_BUG=y.
Reported-and-tested-by: NArnaud Lacombe <lacombar@gmail.com>
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

While removing custom rendezvous code and switching to stop_machine,
commit 192d8857 ("x86, mtrr: use stop_machine APIs for doing MTRR
rendezvous") completely dropped mtrr setting code on !CONFIG_SMP
breaking MTRR settting on UP.

Fix it by removing the incorrect CONFIG_SMP.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NAnders Eriksson <aeriksson@fastmail.fm>
Tested-and-acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes following building error:
--
arch/arm/mach-footbridge/dc21285.c: In function 'dc21285_preinit':
arch/arm/mach-footbridge/dc21285.c:299:2: error: 'vga_base' undeclared (first use in this function)
arch/arm/mach-footbridge/dc21285.c:299:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1
--
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>

This patch fixed following building error:
--
arch/arm/mach-orion5x/pci.c: In function 'orion5x_pci_sys_setup':
arch/arm/mach-orion5x/pci.c:563:2: error: 'vga_base' undeclared (first use in this function)
arch/arm/mach-orion5x/pci.c:563:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/arm/mach-orion5x/pci.o] Error 1
make[1]: *** Waiting for unfinished jobs....
--
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Upstream commit d5341942 "PCI: Make the
struct pci_dev * argument of pci_fixup_irqs const." leaked an extra
"const" into an actual call site (vs a proto/decl) which causes this:

arch/arm/mach-orion5x/dns323-setup.c: In function 'dns323_pci_map_irq':
arch/arm/mach-orion5x/dns323-setup.c:80: error: expected expression before 'const'
arch/arm/mach-orion5x/dns323-setup.c:80: error: too few arguments to function 'orion5x_pci_map_irq'
make[3]: *** [arch/arm/mach-orion5x/dns323-setup.o] Error 1
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NNicolas Pitre <nico@fluxnic.net>
Acked-by: NRalf Baechle <ralf@linux-mips.org>

Commit c03f007a (OMAP: PM:
omap_device: add system PM methods for PM domain handling) mistakenly
used SET_SYSTEM_SLEEP_PM_OPS() when trying to configure custom methods
for the PM domains noirq methods.  Fix that by setting only the
suspend_noirq and resume_noirq methods with custom versions.

Note that all other PM domain methods (including the "normal"
suspend/resume methods) are populated using USE_PLATFORM_PM_SLEEP_OPS,
which configures them all to the default subsystem (platform_bus)
methods.
Reported-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Associate the HDMI clock together with LCDC1 on sh7372.

Without this patch Suspend-to-RAM hangs on the boards
AP4EVB and Mackerel. The code hangs in the LCDC driver
where the software is waiting forever for the hardware to
power down. By explicitly associating the HDMI clock with
LCDC1 we can make sure the HDMI clock is enabled using
Runtime PM whenever the driver is accessing the hardware.

This HDMI and LCDC1 dependency is documented in the sh7372
data sheet. Older kernels did work as expected but the
recently merged (3.1-rc)

 794d78fe drivers: sh: late disabling of clocks V2

introduced code to turn off clocks lacking software reference
which happens to include the HDMI clock that is needed by
LCDC1 to operate as expected.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

The main purpose for PSW restart will be kdump. Therefore customers will
issue "system restart" for creating a dump. If kdump is not enabled,
currently "PSW restart" will reboot the system and then no dump can
be created any more. In order to still allow a manual stand-alone dump in
the case a user issues "PSW restart" on a system that has not enabled
kdump we now stop the system.
Signed-off-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

reipl_fcp_kset was just initialized, so it appears that it should be tested
instead of reipl_kset.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Reported-by: NSuman Saha <sumsaha@gmail.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

When IPL'ing from a block device and an NSS should be created we must
make sure that the kernel image and the initrd are in different 1MB
segments. Otherwise creating the NSS will fail.
So we make sure the initrd is 4MB behind the end of the kernel image
like we do already when IPL via the VM reader is performed.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This was a typo in clockdev declaration for at91sam9261 SoC.
Fix the kernel hanging when switching clocksource to TC (tcb_clksrc).
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRemy Bohmer <linux@bohmer.net>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>