Reset queue mapping when an skb is reentering the stack via a tunnel.
On second pass, the queue mapping from the original device is no
longer valid.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

You can't call atomic_notifier_chain_unregister() while in atomic context.

Fix, call un/register_atmdevice_notifier in module __init and __exit.

Bug report:
http://comments.gmane.org/gmane.linux.network/172603Reported-by: NMikko Vinni <mmvinni@yahoo.com>
Tested-by: NMikko Vinni <mmvinni@yahoo.com>
Signed-off-by: NKarl Hiramoto <karl@hiramoto.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).

Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).

This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.

Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.

Also disable link (reset SIA) before sleep (de4x5 does this too).
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).

de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have for each socket :

One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)

Possible scenarios are :

(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...

(B)
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)

(C)
spin_lock_bh(&sk->sk_slock)
...
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
spin_unlock_bh(&sk->sk_slock)

This (C) case conflicts with (A) :

CPU1 [A]                         CPU2 [C]
read_lock(callback_lock)
<BH>                             spin_lock_bh(slock)
<wait to spin_lock(slock)>
                                 <wait to write_lock_bh(callback_lock)>

We have one problematic (C) use case in inet_csk_listen_stop() :

local_bh_disable();
bh_lock_sock(child); // spin_lock_bh(&sk->sk_slock)
WARN_ON(sock_owned_by_user(child));
...
sock_orphan(child); // write_lock_bh(&sk->sk_callback_lock)

lockdep is not happy with this, as reported by Tetsuo Handa

It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.

Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.
Reported-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets.  This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The subject workaround was causing CRC errors due to writing the wrong
register with updates of the RCTL register.  It was also found that the
workaround function which modifies the RCTL register was being called in
the middle of a read-modify-write operation of the RCTL register, so the
function call has been moved appropriately.  Lastly, jumbo frames must not
be allowed when CRC stripping is disabled by a module parameter because the
workaround requires the CRC be stripped.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 82579, there is a hardware bug that can cause received packets to not
get transferred from the PHY to the MAC due to K1 (a power saving feature
of the PHY-MAC interconnect similar to ASPM L1).  Since the MAC controls
the accounting of missed packets, these will go unnoticed.  Workaround the
issue by setting the K1 beacon duration according to the link speed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two recent patches to cleanup the reset[1] and initial PHY configuration[2]
code paths for ICH/PCH devices inadvertently left out a 10msec delay and
device ID check respectively which are necessary for the 82566DC (device id
0x104b) to be configured properly, otherwise it will not get link.

[1] commit e98cac44
[2] commit 3f0c16e8

CC: stable@kernel.org
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the hardware is prevented from performing automatic PHY configuration
(the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL
register will not get cleared preventing the SMBus address and the LED
configuration to be written to the PHY registers.  On 82579, do not check
the OEM_WRITE_ENABLE bit.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan)
in addition to the MAC before configuring PHY wakeup otherwise the PHY
configuration writes might be missed.  Also write the LED configuration
and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and
e1000_write_smbus_addr, respectively).  The reset is no longer needed
since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and
leaving it in causes issues with auto-negotiating the link.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

otherwise ECT(1) bit will get interpreted as RTO_ONLINK
and routing will fail with XfrmOutBundleGenError.
Signed-off-by: NUlrich Weber <uweber@astaro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are allocated in atl1_setup_ring_resources, zero out the pointers
in atl1_free_ring_resources (like the other resources).
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Acked-by: NChris Snook <chris.snook@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).

Cc: stable@kernel.org
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Acked-by: NChris Snook <chris.snook@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reduces namespace pollution by moving the "struct net" declaration
out of the userspace-facing portion of linux/netlink.h.  It has no impact on
the kernel.

(This came up because we have several C++ applications which use "net" as a
namespace name.)
Signed-off-by: NOllie Wild <aaw@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

we need to check proper socket type within ipv4_conntrack_defrag
function before referencing the nodefrag flag.

For example the tun driver receive path produces skbs with
AF_UNSPEC socket type, and so current code is causing unwanted
fragmented packets going out.
Signed-off-by: NJiri Olsa <jolsa@redhat.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix checksum calculation in nf_nat_snmp_basic.

Based on patches by Clark Wang <wtweeker@163.com> and
Stephen Hemminger <shemminger@vyatta.com>.

https://bugzilla.kernel.org/show_bug.cgi?id=17622Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As soon as rcu_read_unlock() is called, there is no guarantee current
thread can safely derefence t pointer, rcu protected.

Fix is to copy t->alloc_size in a temporary variable.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip_route_me_harder can't create the route cache when the outdev is the same
with the indev for the skbs whichout a valid protocol set.

__mkroute_input functions has this check:
1998         if (skb->protocol != htons(ETH_P_IP)) {
1999                 /* Not IP (i.e. ARP). Do not create route, if it is
2000                  * invalid for proxy arp. DNAT routes are always valid.
2001                  *
2002                  * Proxy arp feature have been extended to allow, ARP
2003                  * replies back to the same interface, to support
2004                  * Private VLAN switch technologies. See arp.c.
2005                  */
2006                 if (out_dev == in_dev &&
2007                     IN_DEV_PROXY_ARP_PVLAN(in_dev) == 0) {
2008                         err = -EINVAL;
2009                         goto cleanup;
2010                 }
2011         }

This patch gives the new skb a valid protocol to bypass this check. In order
to make ipt_REJECT work with bridges, you also need to enable ip_forward.

This patch also fixes a regression. When we used skb_copy_expand(), we
didn't have this issue stated above, as the protocol was properly set.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I initially noticed this because of the compiler warning below, but it
does seem to be a valid concern in the case where ct_sip_get_header()
returns 0 in the first iteration of the while loop.

net/netfilter/nf_conntrack_sip.c: In function 'sip_help_tcp':
net/netfilter/nf_conntrack_sip.c:1379: warning: 'ret' may be used uninitialized in this function
Signed-off-by: NSimon Horman <horms@verge.net.au>
[Patrick: changed NF_DROP to NF_ACCEPT]
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

transparent field of a socket is either inet_twsk(sk)->tw_transparent
for timewait sockets, or inet_sk(sk)->transparent for other sockets
(TCP/UDP).
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Special care should be taken when slow path is hit in ip_fragment() :

When walking through frags, we transfert truesize ownership from skb to
frags. Then if we hit a slow_path condition, we must undo this or risk
uncharging frags->truesize twice, and in the end, having negative socket
sk_wmem_alloc counter, or even freeing socket sooner than expected.

Many thanks to Nick Bowler, who provided a very clean bug report and
test program.

Thanks to Jarek for reviewing my first patch and providing a V2

While Nick bisection pointed to commit 2b85a34e (net: No more
expensive sock_hold()/sock_put() on each tx), underlying bug is older
(2.6.12-rc5)

A side effect is to extend work done in commit b2722b1c
(ip_fragment: also adjust skb->truesize for packets not owned by a
socket) to ipv6 as well.
Reported-and-bisected-by: NNick Bowler <nbowler@elliptictech.com>
Tested-by: NNick Bowler <nbowler@elliptictech.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->truesize is set in core network.

Dont change it unless dealing with fragments.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->truesize is set in core network.

Dont change it unless dealing with fragments.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a RST comes in immediately after checking sk->sk_err, tcp_poll will
return POLLIN but not POLLOUT.  Fix this by checking sk->sk_err at the end
of tcp_poll.  Additionally, ensure the correct order of operations on SMP
machines with memory barriers.
Signed-off-by: NTom Marshall <tdm.code@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just use explicit casts, since we really can't change the
types of structures exported to userspace which have been
around for 15 years or so.
Reported-by: NDan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The family parameter xfrm_state_find is used to find a state matching a
certain policy. This value is set to the template's family
(encap_family) right before xfrm_state_find is called.
The family parameter is however also used to construct a temporary state
in xfrm_state_find itself which is wrong for inter-family scenarios
because it produces a selector for the wrong family. Since this selector
is included in the xfrm_user_acquire structure, user space programs
misinterpret IPv6 addresses as IPv4 and vice versa.
This patch splits up the original init_tempsel function into a part that
initializes the selector respectively the props and id of the temporary
state, to allow for differing ip address families whithin the state.
Signed-off-by: NThomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a driver doesn't fill the entire buffer, old
heap contents may remain, and if it also doesn't
update the length properly, this old heap content
will be copied back to userspace.

It is very unlikely that this happens in any of
the drivers using private ioctls since it would
show up as junk being reported by iwpriv, but it
seems better to be safe here, so use kzalloc.
Reported-by: NJeff Mahoney <jeffm@suse.com>
Cc: stable@kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ipv6 can be a module, we should test CONFIG_IPV6 and CONFIG_IPV6_MODULE
to enable ipv6 bits in ip_gre.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qlcnic driver allocates rx skbs and gives to hardware too bytes of extra
storage, allowing for corruption of kernel data.

NET_IP_ALIGN being 0 on some platforms (including x86), drivers should
not assume it's 2.

rds_ring->skb_size = rds_ring->dma_size + NET_IP_ALIGN;
...
skb = dev_alloc_skb(rds_ring->skb_size);
skb_reserve(skb, 2);
pci_map_single(pdev, skb->data, rds_ring->dma_size, PCI_DMA_FROMDEVICE);

(and rds_ring->skb_size == rds_ring->dma_size) -> bug


Because of extra alignment (1500 + 32) -> four extra bytes are available
before the struct skb_shared_info, so corruption is not noticed.

Note: this driver could use netdev_alloc_skb_ip_align()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Direct Cache Access is not supported on IOAT ver.3.0 multiple-IOH platforms.
This patch blocks registering of dca providers when multiple IOH detected with IOAT ver.3.0.
Signed-off-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We cannot use rcu_dereference_bh safely in netpoll_rx as we may
be called with IRQs disabled.  We could however simply disable
IRQs as that too causes BH to be disabled and is safe in either
case.

Thanks to John Linville for discovering this bug and providing
a patch.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_packet_config() is called when getting the packet ready
for appending of chunks.  The function should not touch the
current state, since it's possible to ping-pong between two
transports when sending, and that can result packet corruption
followed by skb overlfow crash.
Reported-by: NThomas Dreibholz <dreibh@iem.uni-due.de>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When uCode error condition detected, driver try to perform either
rf reset or firmware reload in order bring device back to
working condition.

If rf reset is required and scan is in process, there is no need
to issue rf reset since scan already reset the rf.

If firmware reload is required and scan is in process, skip the
reload request. There is a possibility firmware reload during
scan cause problem.

[  485.804046] WARNING: at net/mac80211/main.c:310 ieee80211_restart_hw+0x28/0x62()
[  485.804049] Hardware name: Latitude E6400
[  485.804052] ieee80211_restart_hw called with hardware scan in progress
[  485.804054] Modules linked in: iwlagn iwlcore bnep sco rfcomm l2cap crc16 bluetooth [last unloaded: iwlcore]
[  485.804069] Pid: 812, comm: kworker/u:3 Tainted: G        W   2.6.36-rc3-wl+ #74
[  485.804072] Call Trace:
[  485.804079]  [<c103019a>] warn_slowpath_common+0x60/0x75
[  485.804084]  [<c1030213>] warn_slowpath_fmt+0x26/0x2a
[  485.804089]  [<c145da67>] ieee80211_restart_hw+0x28/0x62
[  485.804102]  [<f8b35dc6>] iwl_bg_restart+0x113/0x150 [iwlagn]
[  485.804108]  [<c10415d5>] process_one_work+0x181/0x25c
[  485.804119]  [<f8b35cb3>] ? iwl_bg_restart+0x0/0x150 [iwlagn]
[  485.804124]  [<c104190a>] worker_thread+0xf9/0x1f2
[  485.804128]  [<c1041811>] ? worker_thread+0x0/0x1f2
[  485.804133]  [<c10451b0>] kthread+0x64/0x69
[  485.804137]  [<c104514c>] ? kthread+0x0/0x69
[  485.804141]  [<c1002df6>] kernel_thread_helper+0x6/0x10
[  485.804145] ---[ end trace 3d4ebdc02d524bbb ]---
[  485.804148] WG> 1
[  485.804153] Pid: 812, comm: kworker/u:3 Tainted: G        W   2.6.36-rc3-wl+ #74
[  485.804156] Call Trace:
[  485.804161]  [<c145da9b>] ? ieee80211_restart_hw+0x5c/0x62
[  485.804172]  [<f8b35dcb>] iwl_bg_restart+0x118/0x150 [iwlagn]
[  485.804177]  [<c10415d5>] process_one_work+0x181/0x25c
[  485.804188]  [<f8b35cb3>] ? iwl_bg_restart+0x0/0x150 [iwlagn]
[  485.804192]  [<c104190a>] worker_thread+0xf9/0x1f2
[  485.804197]  [<c1041811>] ? worker_thread+0x0/0x1f2
[  485.804201]  [<c10451b0>] kthread+0x64/0x69
[  485.804205]  [<c104514c>] ? kthread+0x0/0x69
[  485.804209]  [<c1002df6>] kernel_thread_helper+0x6/0x10
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

If the alloc_skb() fails then we return 65431 instead of -ENOBUFS
(-105).
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The atlx drivers are sufficiently mature that we no longer need a separate
mailing list for them.  Move the discussion to netdev, so we can decommission
atl1-devel, which is now mostly spam.
Signed-off-by: NChris Snook <chris.snook@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed formatting (tabs and line breaks).

The CHELSIO_GET_QSET_NUM device ioctl allows unprivileged users to read
4 bytes of uninitialized stack memory, because the "addr" member of the
ch_reg struct declared on the stack in cxgb_extension_ioctl() is not
altered or zeroed before being copied back to the user.  This patch
takes care of it.
Signed-off-by: NDan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>