ASoC: Updates for v3.13

 - Further work on the dmaengine helpers, including support for
   configuring the parameters for DMA by reading the capabilities of the
   DMA controller which removes some guesswork and magic numbers fromm
   drivers.
 - A refresh of the documentation.
 - Conversions of many drivers to direct regmap API usage in order to
   allow the ASoC level register I/O code to be removed, this will
   hopefully be completed by v3.14.
 - Support for using async register I/O in DAPM, reducing the time taken
   to implement power transitions on systems that support it.

hdmi_setup_audio_infoframe() does not set up pin and infoframe if there
is no connected sink. If a sink is connected while audio playback is
already in progress, the pin and infoframe will not be properly set up,
causing no audio or wrongly mapped audio.

On Intel Haswell codecs the hdmi_setup_audio_infoframe() is already
called again from hdmi_present_sense() when an ELD appears because
transcoder:port mapping may have changed.

Make the call non-Haswell-specific so that audio will be properly set up
if the playback was started before a sink was connected.

Tested on non-Haswell Intel HDMI codec by plugging sink in during
playback.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Recent AMD HDMI codecs (revision ID 3 and later, 0x100300 as reported by
procfs codec#0) have a configurable ramp-up/down functionality.

The documentation ( http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf )
specifies that 180 ("180/256 =~ 0.7") is recommended for PCM and 0 for
non-PCM.

Apply the recommended values according to provided S/PDIF AES0 settings
since ramp-up/down does not make sense for non-PCM.

v2: adapted to hdmi_ops infrastructure

* More note from Anssi:
actually, re-reading mails reveals that Olivier didn't find the
expected difference with this setting, except for "maybe slightly
slower startup with AES0=6" (i.e. value 0, which is unexpected).

So maybe
a) it makes too unnoticiable a difference, or
b) only affects certain hardware (card and/or sink), or
c) ramp-up/down is only triggered with the MUTE bit of
   ATI_VERB_SET_MULTICHANNEL_xx which is also rev3+ specific,
   but is not presently used by the driver,
or something else.

So there's a significant chance setting ramp rate is useless for us ATM,
but probably does not do actual harm either.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: Olivier Langlois <olivier@trillion01.com> # v1
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ATI/AMD HDMI codecs do not include standard HDA HDMI HBR support (which
is required for bitstreaming DTS-HD and Dolby TrueHD), instead they have
custom verbs for checking and enabling it.

Add support for the ATI/AMD HDMI HBR verbs.

The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf

v2: adapted to hdmi_ops infrastructure
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v1
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ATI/AMD HDMI/DP codecs do not include standard HDA ELD (EDID-like data)
support.

In place of providing access to an ELD buffer, various vendor-specific
verbs are provided to provide the relevant information. Revision ID 3
and later (0x100300 as reported by procfs codec#X) have support for
providing more information than the previous revisions (but only if
supported by the display driver).

Generate ELD from the information provided by the vendor-specific verbs
on ATI/AMD codecs.

The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf

v2: moved code to hda_eld.c and cleaned it up
v3: adapted to hdmi_ops infrastructure
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ATI/AMD codecs do not support all the standard HDA HDMI/DP functions,
instead various vendor-specific verbs are provided.

This commit addresses these missing functions:
- standard channel mapping support
- standard infoframe configuration support

ATI/AMD provides their own verbs that allow the following:
- setting CA for infoframe
- setting down-mix information for infoframe
- channel pair remapping
- individual channel remapping (revision ID 3+, 0x100300+)

The documentation for the verbs has now been released by AMD:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf

Add support for the ATI/AMD specific verbs and use them instead of the
generic methods on ATI/AMD codecs. This allows multi-channel PCM audio
to work.

Channel remapping is restricted to pairwise mapping on codecs with
revision ID 2 (0x100200 as reported by procfs codec#X) or lower. This
means cards up to Radeon HD7670 as far as I know. This will not affect
standard multi-channel modes since these codecs support automatic
FC-LFE swapping for HDMI.

ATI/AMD codecs do not advertise all of their supported rates, formats
and channel counts, therefore that information is forced accordingly so
that all HDMI 1.x PCM parameters are marked as supported.

Support for multiple ports is also added to patch_atihdmi so that
0x1002aa01 codecs with multiple ports will work properly when switched
back to that patch.

v2: splitted ELD emulation to a separate patch, tlv fixes
v3: adapted to the new hdmi_ops infrastructure, fixed rev3+ vendor id
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2+rev3fix
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Upcoming AMD multichannel support requires many customized operations
(channel mapping, ELD, HBR) but can otherwise share most of its code
with the generic patch.

Add a local struct hdmi_ops containing customizable HDMI-specific
callbacks and move the current code to those callbacks. Functionality is
unaltered.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some machine with 85ms delay might be happen pop noise when codec
enter to D3.  Raise up to 100ms delay will be match for more machine.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The drain and drain_notify callback were blocked by low level driver untill the
draining was complete. Due to this being invoked with big fat mutex held, others
ops like reading timestamp, calling pause, drop were blocked.

So to fix this we add a new snd_compr_drain_notify() API. This would be required
to be invoked by low level driver when drain or partial drain has been completed
by the DSP. Thus we make the drain and partial_drain callback as non blocking
and driver returns immediately after notifying DSP.
The waiting is done while relasing the lock so that other ops can go ahead.
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
CC: stable@vger.kernel.org
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It turned out that we can't use gen_pool_*() functions on archs
without CONFIG_GENERIC_ALLOCATOR (resulting in missing symbols), since
linux/genalloc.h doesn't provide dummy functions for all.  We'd be
able to fix linux/genalloc.h size, but I take an easier path for
now...
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>