tx_timeout reset path needs to re-init dev and re-apply nic cfg to
enable vlan stripping.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report all bad FCS errs as frames errs.  This includes frames with bad
FCS on wire detected by MAC and frames which may be truncated due to
ingress FIFO overruns.  No longer print a driver msg on bad FCS err.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return notify intr credits after notify intr from firmware.  This is
especially important for legacy PCI intr mode, where not returning
credits would cause PBA to remain asserted which would get us right
back into the ISR.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/gianfar.c

PPP is modular code so no initdata on netns hooks.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

> Kernel BUG at drivers/net/tun.c:444
> invalid opcode: 0000 [1] SMP
> last sysfs file: /class/net/lo/ifindex
> CPU 0
> Modules linked in: tun ipt_MASQUERADE iptable_nat ip_nat xt_state ip_conntrack
> nfnetlink ipt_REJECT xt_tcpudp iptable_filter d
> Pid: 6912, comm: qemu-kvm Tainted: G      2.6.18-128.el5 #1
> RIP: 0010:[<ffffffff886f57b0>]  [<ffffffff886f57b0>]
> :tun:tun_chr_readv+0x2b1/0x3a6
> RSP: 0018:ffff8102202c5e48  EFLAGS: 00010246
> RAX: 0000000000000000 RBX: ffff8102202c5e98 RCX: 0000000004010000
> RDX: ffff810227063680 RSI: ffff8102202c5e9e RDI: ffff8102202c5e92
> RBP: 0000000000010ff6 R08: 0000000000000000 R09: 0000000000000001
> R10: ffff8102202c5e94 R11: 0000000000000202 R12: ffff8102275357c0
> R13: ffff81022755e500 R14: 0000000000000000 R15: ffff8102202c5ef8
> FS:  00002ae4398db980(0000) GS:ffffffff803ac000(0000) knlGS:0000000000000000
> CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
> CR2: 00002ae4ab514000 CR3: 0000000221344000 CR4: 00000000000026e0
> Process qemu-kvm (pid: 6912, threadinfo ffff8102202c4000, task
> ffff81022e58d820)
> Stack:  00000000498735cb ffff810229d1a3c0 0000000000000000 ffff81022e58d820
>  ffffffff8008a461 ffff81022755e528 ffff81022755e528 ffffffff8009f925
>  000005ea05ea0000 ffff8102209d0000 00001051143e1600 ffffffff8003c00e
> Call Trace:
>  [<ffffffff8008a461>] default_wake_function+0x0/0xe
>  [<ffffffff8009f925>] enqueue_hrtimer+0x55/0x70
>  [<ffffffff8003c00e>] hrtimer_start+0xbc/0xce
>  [<ffffffff886f58bf>] :tun:tun_chr_read+0x1a/0x1f
>  [<ffffffff8000b3f3>] vfs_read+0xcb/0x171
>  [<ffffffff800117d4>] sys_read+0x45/0x6e
>  [<ffffffff8005d116>] system_call+0x7e/0x83
>
>
> Code: 0f 0b 68 40 62 6f 88 c2 bc 01 f6 42 0a 08 74 0c 80 4c 24 41
> RIP  [<ffffffff886f57b0>] :tun:tun_chr_readv+0x2b1/0x3a6
>  RSP <ffff8102202c5e48>
>  <0>Kernel panic - not syncing: Fatal exception

This crashed when an LRO packet generated by bnx2x reached a
tun device through the bridge.  We're supposed to drop it at
the bridge.  However, because the check was placed in br_forward
instead of __br_forward, it's only effective if we are sending
the packet through a single port.

This patch fixes it by moving the check into __br_forward.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the user creates IPv6 over IPv6 tunnel, the device name created
by the kernel isn't set to t->parm.name, which is referred as the
result of ioctl().
Signed-off-by: NNoriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ira Snyder found that commit 8c7396ae
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: NIra Snyder <iws@ovro.caltech.edu>
Reported-by: NPeter Korsgaard <jacmet@sunsite.dk>
Bisected-by: NIra Snyder <iws@ovro.caltech.edu>
Tested-by: NPeter Korsgaard <jacmet@sunsite.dk>
Tested-by: NIra Snyder <iws@ovro.caltech.edu>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When user tries to map all chunks given in argument, kernel
works on a copy of the chunkmap, but at the end it doesn't
check the copy, but the orginal one.
Signed-off-by: NQu Haoran <haoran.qu@6wind.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes echoing if the socket that has sent the request to
create/update/delete an entry is not subscribed to any multicast
group. With the current code, ctnetlink would not send the echo
message via unicast as nfnetlink_send() would be skip.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an inconsistency in the current ctnetlink code
since NAT sequence adjustment bit can only be updated but not set
in the conntrack entry creation.

This patch is used by conntrackd to successfully recover newly
created entries that represent connections with helpers and NAT
payload mangling.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes connection tracking handling for ICMPv6 messages
related to Stateless Address Autoconfiguration, MLD, and MLDv2. They
can not be tracked because they are massively using multicast (on
pre-defined address). But they are not invalid and should not be
detected as such.
Signed-off-by: NEric Leblond <eric@inl.fr>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch fixes a typo in the inverse mapping of Node Information
request. Following draft-ietf-ipngwg-icmp-name-lookups-09, "Querier"
sends a type 139 (ICMPV6_NI_QUERY) packet to "Responder" which answer
with a type 140 (ICMPV6_NI_REPLY) packet.
Signed-off-by: NEric Leblond <eric@inl.fr>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gro: Optimise TCP packet reception

As this function can be called more than half a million times for
10GbE, it's important to optimise it as much as we can.

This patch uses bit ops to logical ops, as well as open coding
memcmp to exploit alignment properties.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As this function can be called more than half a million times for
10GbE, it's important to optimise it as much as we can.

This patch does some obvious changes to use 2-byte and 4-byte
operations instead of byte-oriented ones where possible.  Bit
ops are also used to replace logical ops to reduce branching.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch optimises the Ethernet header comparison to use 2-byte
and 4-byte xors instead of memcmp.  In order to facilitate this,
the actual comparison is now carried out by the callers of the
shared dev_gro_receive function.

This has a significant impact when receiving 1500B packets through
10GbE.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares for the move of the same_flow checks out of
dev_gro_receive.  As such we need to remember the number of held
packets since doing a loop just to count them every time is silly.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several devices need to insert some "pre headers" in front of the
main packet data when they transmit a packet.

Currently we allocate only 16 bytes of pad room and this ends up not
being enough for some types of hardware (NIU, usb-net, s390 qeth,
etc.)

So increase this to 32.

Note that drivers still need to check in their transmit routine
whether enough headroom exists, and if not use skb_realloc_headroom().
Tunneling, IPSEC, and other encapsulation methods can cause the
padding area to be used up.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Cut down msi-x vectors from 8 to 1 since only one is used for now.
o Use separate handler for msi-x, that doesn't unnecessarily scrub
  msi status register.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DescOwn should not be set, thus allowing the chip to use the
descriptor, before everything else is set up correctly.
Signed-off-by: NRisto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tap devices can make use of a small MAC filter set via the
TUNSETTXFILTER ioctl.  The filter has a set of exact matches
plus a hash for imperfect filtering of additional multicast
addresses.  The current code is unbalanced, adding unicast
addresses to the multicast hash, but only checking the hash
against multicast addresses.  This results in the filter
dropping unicast addresses that overflow the exact filter.
The fix is simply to disable the filter by leaving count set
to zero if we find non-multicast addresses after the exact
match table is filled.
Signed-off-by: NAlex Williamson <alex.williamson@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@

(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
     when != if (...) { <+...x...+> }
x->f = E
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@

(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
     when != if (...) { <+...x...+> }
x->f = E
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-agn.c
	drivers/net/wireless/iwlwifi/iwl3945-base.c

Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the version number to 1.3.16 and update copyright dates for 2009.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses two minor items I found while cleaning up the igb
driver for our sourceforge version.

The first clears the context index if we don't flag that we need it.

The second item is that eims_other should be used instead of bit defines
when setting all of the EICS bits prior to reset.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was seen with repeated interface up/down testing that there was a large
stray between the stats reported by the queues and the stats reported by the
HW.  It was found to be an issue in that hw stats were being reset without
first being recorded.  This change records the stats before wiping them from
the system via the reset.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the setting of ring->count variables from igb_probe as they are
duplicating the same configuration that is done igb_alloc_queues.

Remove the err_hw_init tag as it can be replaced by err_sw_init.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The disable_av variable is never used by the driver and provides no value as
it is likely a leftover debugging variable.  I have removed it and replaced
the one spot that checked for it with a check for a valid address.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As additional hardware is added to the igb driver it is easier to support
the expansion via switch statements instead of using nested ifs.  For
this reason I am changing this to a switch statement.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move igb_get_hw_control up so that it is called just after the reset in
igb_resume.  This notifies the HW sooner that the driver is reassuming
control of the device.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupt handler was reading eicr and then doing nothing with the
result.  I have removed the variable and the register read since they
provide no value to the legacy interrupt handler.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were several spots in the code making calls to adapter->hw when they
could have just been accessing hw-> directly.  I cleaned up the spots where
this was visibly apparent.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There isn't much point in having the _82575 hanging off the end of this
function since there aren't any other version of this function running
around within this driver.  This also allows for a bit of whitespace
cleanup due to a shorter function name.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The igb watchdog task is modifying the watchdog timer twice duing a single
run.  It only needs to be called once to reschedule itself for 2 seconds from
the last time it ran.

In addition I removed the allocation of the mac_info structure since it is
only called twice and is easier to access via the e1000_hw struct.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up igb_netpoll so that it is more friendly with both the
current napi and newly introduced GRO features.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a counter for dma out of sync errors reported via interrupt.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the code for the testing has pretty much become stale at this point
and is need of update.  This update just streamlines most of the code,
widens the range of interrupt testing.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver is currently using HW_CSUM which is not correct.  Update this
to use the IP_CSUM and IPV6_CSUM flags.  In addition consolidate the TSO
flag setting.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>