* Rename it8213_tuneproc() to it8213_tune_pio() and add it8213_tuneproc()
  wrapper.  Move finding of the best PIO mode to the new wrapper.

* Add setting of transfer mode on the device to it8213_tuneproc().

* Don't call it8213_dma_2_pio() for PIO modes in it8213_tune_chipset().

* Use it8213_tuneproc() in it8213_config_drive_for_dma().

v2:
* Remove PIO modes from it8213_dma_2_pio(), they are no longer needed there
  (Noticed by Sergei)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix cs5535_tuneproc() to pass PIO transfer mode value instead of PIO mode
  number to cs5535_set_speed() (fixes random PIO timings being programmed
  and a possible OOPS).  Do a little cleanup while at it.

* Fix cs5535_set_speed() to check if the mate device is present (fixes PIO0
  taskfile timings being used if there is no other device on the cable).

* Use cs5535_tuneproc() in cs5535_dma_check().  The old code had the same
  issue as cs5535_tuneproc() and add additionally caused 0x00-0x04 transfer
  mode values (== default PIO, default PIO w/ IORDY + two invalid values)
  being set on the device instead of values 0x08-0x0c (XFER_PIO_[0,4]).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

 drivers/scsi/ide-scsi.c | 34642 -> 34536 (-106 bytes)
 drivers/scsi/ide-scsi.o | 171728 -> 171524 (-204 bytes)
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Is this a bug? In original verison memset cleared sizeof(state) bytes
instead of sizeof(*state). If it was intentional then this patch is invalid.
If not intentional -> valid :) Please review.

Bart: Yes, it is a bug so this patch is a valid bugfix. :-)

 drivers/ide/arm/icside.c | 18883 -> 18849 (-34 bytes)
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

drivers/ide/ide-tape.c: In function '__idetape_kmalloc_stage':
drivers/ide/ide-tape.c:2588: warning: large integer implicitly truncated to unsigned type
drivers/ide/ide-tape.c:2616: warning: large integer implicitly truncated to unsigned type

b_size in struct idetape_bh is an unsigned short.  We sometimes assigne
PAGE_SIZE to it and PAGE_SIZE can be 64K or larger, so make it a u32.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix a couple of runtogether printks in cmd64x.c IDE driver by adding 
proper newlines.
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Recognise the FSC Amilo A1630's incarnation of a SiS5513 chip as laptop to
get UDMA100 support.
Signed-off-by: NDavid Lamparter <equinox@diac24.net>
Cc: Lionel Bouton <Lionel.Bouton@inet6.fr>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Direct port of Alan's fix for pata_ali.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

As found by the Coverity checker, and reported by Adrian Bunk, this
fixes a overrun error in the CS5535 IDE driver.  Somebody got a little
excited with the if() statement - the CS5535 only supports UDMA 0-4.

Bart:
Not a bug per se since the upper layer will never feed this function
with speed > XFER_UDMA_4 (thanks to ->ultra_mask being set to 0x1f).

Worth fixing anyway.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Alexey Dobriyan noticed that the new WARN_ON() semantics that were
introduced by commit 684f9783 (to also
return the value to be warned on) didn't compile when given a bitfield,
because the typeof doesn't work for bitfields.

So instead of the typeof trick, use an "int" variable together with a
"!!(x)" expression, as suggested by Al Viro.

To make matters more interesting, Paul Mackerras points out that that is
sub-optimal on Power, but the old asm-coded comparison seems to be buggy
anyway on 32-bit Power if the conditional was 64-bit, so I think there
are more problems there.

Regardless, the new WARN_ON() semantics may have been a bad idea.  But
this at least avoids the more serious complications.

Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
  [WATCHDOG] Fix pcwd_init_module crash
  [WATCHDOG] ICH9 support for iTCO_wdt
  [WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
  [WATCHDOG] 631xESB/632xESB support for iTCO_wdt
  [WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
  [WATCHDOG] Return value of nonseekable_open
  [WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
  [WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
  [WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
  [WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
  [WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
  [WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
  [WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
  [WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
  [WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
  [WATCHDOG] mv64x60_wdt: Get register address from platform data
  [WATCHDOG] mv64x60_wdt: set up platform_device in platform code
  [WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
  [WATCHDOG] s3c2410_wdt: fixup after arch include moves
  [WATCHDOG] git-watchdog-typo
  ...

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (50 commits)
  [MIPS] Add smp_call_function_single()
  [MIPS] thread_info.h: kmalloc + memset conversion to kzalloc
  [MIPS] Kexec: Fix several 64-bit bugs.
  [MIPS] Kexec: Fix several warnings.
  [MIPS] DDB5477: Remove support
  [MIPS] Fulong: Remove unneeded header file
  [MIPS] Cobalt: Enable UART on RaQ1
  [MIPS] Remove unused GROUP_TOSHIBA_NAMES
  [MIPS] remove some duplicate includes
  [MIPS] Oprofile: Fix rm9000 performance counter handler
  [MIPS] Use -Werror on subdirectories which build cleanly.
  [MIPS] Yosemite: Fix warning.
  [MIPS] PMON: Fix cpustart declaration.
  [MIPS] Yosemite: Only build ll_ht_smp_irq_handler() if HYPERTRANSPORT.
  [MIPS] Yosemite: Fix build error due to undeclared titan_mailbox_irq().
  [MIPS] Yosemite: Don't declare titan_mailbox_irq() as asmlinkage.
  [MIPS] Yosemite: Fix warnings in i2c-yoesmite by deleting the unused code.
  [MIPS] Delete unused arch/mips/gt64120/common/
  [MIPS] Fix build warning in unaligned load/store emulator.
  [MIPS] IP32: Don't ignore request_irq's return value.
  ...

* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
  hwmon: fscher read control bugfix
  hwmon: (adm1031) Fix broken links in documentation
  hwmon: make abituguru3_read_increment_offset() static
  hwmon: Fix regression caused by typo in lm90.c
  hwmon: (applesmc) add temperature sensors set for Macbook
  hwmon: fscher control update bugfix
  hwmon: fix dme1737 temp fault attribute
  hwmon: Add missing __devexit tags in various drivers
  hwmon: clean up duplicate includes
  hwmon: fix lm78 detection regression
  hwmon: fix array overruns in lm93.c
  hwmon: add support for THMC50 and ADM1022

CONFIG_ACPI_PROCFS_SLEEP is a NO-OP -- delete it (again).

Apparently 296699de creating CONFIG_SUSPEND
and CONFIG_PM_SLEEP was based on an out-dated version of drivers/acpi/Kconfig,
as it erroneously restored this recently deleted config option.
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

scripts/kconfig/conf -o arch/arm/Kconfig
arch/arm/Kconfig:994: can't open file "drivers/acorn/block/Kconfig"

Cc: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
  [x86 setup] EDD: Fix the computation of the MBR sector buffer
  [x86 setup] Newline after setup signature failure message
  x86 boot code comments typos

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
  [RTNETLINK]: Fix warning for !CONFIG_KMOD
  [IPV4] ip_options.c: kmalloc + memset conversion to kzalloc
  [DECNET]: kmalloc + memset conversion to kzalloc
  [NET]: ethtool_perm_addr only has one implementation
  [NET]: ethtool ops are the only way
  [PPPOE]: Improve hashing function in hash_item().
  [XFRM]: State selection update to use inner addresses.
  [IPSEC]: Ensure that state inner family is set
  [TCP]: Bidir flow must not disregard SACK blocks for lost marking
  [TCP]: Fix ratehalving with bidirectional flows
  [PPPOL2TP]: Add CONFIG_INET Kconfig dependency.
  [NET]: Page offsets and lengths need to be __u32.
  [AF_UNIX]: Make code static.
  [NETFILTER]: Make nf_ct_ipv6_skip_exthdr() static.
  [PKTGEN]: make get_ipsec_sa() static and non-inline
  [PPPoE]: move lock_sock() in pppoe_sendmsg() to the right location
  [PPPoX/E]: return ENOTTY on unknown ioctl requests
  [IPV6]: ipv6_addr_type() doesn't know about RFC4193 addresses.
  [NET]: Fix prio_tune() handling of root qdisc.
  [NET]: Fix sch_api to properly set sch->parent on the root.
  ...

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [BBC_I2C]: kmalloc + memset conversion to kzalloc
  [BBC_ENVCTRL]: kmalloc + memset conversion to kzalloc
  [SPARC]: Fix exec failures on sun4c.
  [SPARC] Videopix Frame Grabber: Fix unreleased lock in vfc_debug()
  [SPARC64]: Add missing dma_get_cache_alignment().
  [SUNLANCE]: Fix sparc32 crashes by using of_*() interfaces.

Since irq in m48t59_private struct is defined as 'unsigned int', which will
make the following if sentence to be never true:

         if (m48t59->irq < 0)
                  m48t59->irq = NO_IRQ;

And thus it will make the m48t59_rtc_probe() is failed when the driver is
working in a no irq mode:
Signed-off-by: NMark Zhan <rongkai.zhan@windriver.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change Kconfig objects from "menu, config" into "menuconfig" so that the
user can disable the whole feature without having to enter the menu first.
Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the #ifdef guard above these functions to remove the warnings.
Signed-off-by: NCharlie Shepherd <masterdriverz@gentoo.org>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This updates some error reporting paths in SPI device setup:

 - Move validation logic for SPI chipselects to spi_new_device(),
   which is where it should always have been.

 - In spi_new_device(), emit error messages if the device can't
   be created.  This is LOTS better than a silent failure; though
   eventually, the calling convention should probably change to
   use the <linux/err.h> conventions.

 - Includes one previously-missing check:  SPI masters must always
   have at least one chipselect, even for dedicated busses which
   always keep it selected!

It also adds a FIXME (IDR for dynamic ID allocation) so the issue doesn't live
purely in my mailbox.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds kerneldoc to the SPI framework.  The "spi_driver" and
"spi_board_info" structs were previously not described.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/message/i2o/i2o_block.c: In function 'i2o_block_transfer':
drivers/message/i2o/i2o_block.c:837: warning: integer overflow in expression

msg->u.head[1] = cpu_to_le32(I2O_CMD_PRIVATE << 24 | HOST_TID << 12 | tid);
and I2O_CMD_PRIVATE is defined as 0xFF.  This gets "0xFF0100 | tid" and fits
into 32-bit unsigned but not into 32-bit signed integer properly.  Target
value is defined as u32 so the claculation does not fit during computation.

Change local variable tid to u32 so the whole expression is of u32 type and
fits well into u32 result.
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Cc: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

CONFIG_PCI=n:

drivers/char/ip2/ip2main.c: In function `ip2_loadmain':
drivers/char/ip2/ip2main.c:503: warning: unused variable `status'
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fix weird behaviour of UDF mounting procedure.  To get UID
changed (for now) we have to type

	mount -t udf -o uid=some_user,uid=ignore /dev/device /mnt/moun_point

and specifying two uid at once is strange a bit.  So with the patch we are
able to mount without additional 'uid=ignore' option.  The same for GID
option is done.

This patch will not break current mount scheme (with two option).

Btw this does fix (I hope) the following

	[BUG 6124] mount of UDF fs ignores UID and GID options
        http://bugzilla.kernel.org/show_bug.cgi?id=6124Signed-off-by: NCyrill Gorcunov <gorcunov@gmail.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael <auslands-kv@gmx.de>
Cc: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There's a memory leak in the cciss driver.

in alloc_cciss_hba() we may leak sizeof(ctlr_info_t) bytes if a
call to alloc_disk(1 << NWD_SHIFT) fails.
This patch should fix the issue.

Spotted by the Coverity checker.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Acked-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the top level menu "Code maturity level options", and moves its
options into menu "General setup".

This makes Kconfig less cluttered and easier to setup.
Signed-off-by: NAl Boldi <a1426z@gawab.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Videopix Frame Grabber: vfc_debug() doesn't release the device lock
when copy_from_user() fails
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: N"David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make it a little more clear that this is the default implementation for
the setleast operation.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: N"J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a set of small fixes addressing points raised with the original
driver submission.  In particular, __maybe_unused is used rather than a
local hack and sbd_ops is made const.  Additionally I have made two local
string variables automatic as rodata space was wasted for pointers
unnecessarily.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

C files should include the header files that prototype their functions.

Eliminates a sparse warning:
warning: symbol 'check_bugs' was not declared. Should it be static?
Signed-off-by: NJosh Triplett <josh@kernel.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

C files should include the header files that prototype their functions.

Eliminates a sparse warning:
warning: symbol 'check_bugs' was not declared. Should it be static?
Signed-off-by: NJosh Triplett <josh@kernel.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Typo fixes errror -> error
Signed-off-by: NGabriel Craciunescu <nix.or.die@googlemail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"error" is always equal to 0.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Coverity spotted what looks like a real possible case of using a variable
after it has been freed.  The problem is in
kernel/relay.c::relay_open_buf()

If the code hits "goto free_buf;" it ends up in this code :

  free_buf:
    	relay_destroy_buf(buf);	<--- calls kfree() on 'buf'.
  free_name:
   	kfree(tmpname);
  end:
  	return buf;		<-- use after free of 'buf'.

I read through the callers and they all handle a NULL return from this
function as an error (and hitting the 'free_buf' label only happens on
failure to chan->cb->create_buf_file(), so that looks like a clear error to
me).

The patch simply sets 'buf' to NULL after the call to
relay_destroy_buf(buf); - as far as I can see that should take care of the
problem.

The patch also corrects a reference to a documentation file while
I was at it.

Note from Mathieu: the documentation reference change should have been
done in a separate patch, but I guess no one will really care.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Acked-by: N"David J. Wilder" <wilder@us.ibm.com>
Tested-by: N"David J. Wilder" <wilder@us.ibm.com>
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Tom Zanussi <zanussi@us.ibm.com>
Cc: Karim Yaghmour <karim@opersys.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

WARNING: kernel/built-in.o(.text+0x16910): Section mismatch:
reference to .init.text: (between 'kthreadd' and 'init_waitqueue_head')

comes because kernel/kthread.c:kthreadd() is not __init but calls
kthreadd_setup() which is __init. But this is ok, because kthreadd_setup()
is only ever called at init time, and then kthreadd() proceeds into its
"for (;;)" loop. We could mark kthreadd __init_refok, but kthreadd_setup()
with just one callsite and 4 lines in it (it's been that small since
10ab825b) doesn't need to be a separate function at all -- so let's
just move those four lines at beginning of kthreadd() itself.
Signed-off-by: NSatyam Sharma <ssatyam@cse.iitk.ac.in>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When buf_check_overflow() returns != 0 we will hit kfree(ERR_PTR(err)) and
it will not be happy about it.
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: Eric Van Hensbergen <ericvh@ericvh.myip.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It is possible that another process could acquire a new file lease right
after break_lease() is called during a truncate, but before lease-granting
is disabled by the subsequent get_write_access().  Merely switching the
order of the break_lease() and get_write_access() calls prevents this race.
Signed-off-by: NDavid M. Richter <richterd@citi.umich.edu>
Signed-off-by: N"J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>