Remove DEBUG define, key debug spew off of the module's debug param that
already exists.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Per hardware provided to me, the Formosa Industrial Computing eHome
Infrared Receiver, 0x147a:0xe017, has no tx capability, it is rx only.

Thanks go to Paul Rae for the hardware.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks to some excellent investigative work by Douglas Clowes, it was
uncovered that the older w83667hg Nuvoton chip functions with this
driver after actually enabling the CIR function via its multi-function
chip config register. The CIR and CIR wide-band sensor enable bits are
just in a different place on this hardware, so we only poke register
0x27 on 677 hardware now, and we poke register 0x2c on the 667 now.
Reported-by: NDouglas Clowes <dclowes1@optusnet.com.au>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are additional chip IDs that report a PNP ID of NTN0530, which we
were refusing to load on. Instead, lets just warn if we encounter an
unknown chip, as there's a chance it will work just fine.

Also, expand the list of known hardware to include both an earlier and a
later generation chip that this driver should function with. Douglas has
an older w83667hg variant, that with a touch more work, will be
supported by this driver, and Lutz has a newer w83677hg variant that
works without any further modifications to the driver.
Reported-by: NDouglas Clowes <dclowes1@optusnet.com.au>
Reported-by: NLutz Sammer <johns98@gmx.net>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the newly introduced KEY_IMAGES where appropriate, and standardize
on KEY_MEDIA for media center/application launcher button (such as the
Windows logo key on the Windows Media Center Ed. remotes).
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Kinect sensor is a device used by Microsoft for its Kinect project,
which is a system for controller-less Human-Computer interaction
targeted for Xbox 360.

In the Kinect device, RGBD data is captured from two distinct sensors: a
regular RGB sensor and a monochrome sensor which, with the aid of a IR
structured light, captures what is finally exposed as a depth map; so
what we have is basically a Structured-light 3D scanner.

The Kinect gspca subdriver just supports the video stream for now,
exposing the output from the RGB sensor or the unprocessed output from
the monochrome sensor; it does not deal with the processed depth stream
yet, but it allows using the sensor as a Webcam or as an IR camera (an
external source of IR light might be needed for this use).

The low level implementation is based on code from the OpenKinect
project (http://openkinect.org).
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a 10 bits per pixel greyscale format in a bit-packed array representation,
naming it Y10B. Such pixel format is supplied for instance by the Kinect
sensor device.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NPatrice CHOTARD <patricechotard@free.fr>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NPatrice CHOTARD <patricechotard@free.fr>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NPatrice CHOTARD <patricechotard@free.fr>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NPatrice CHOTARD <patricechotard@free.fr>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NPatrice CHOTARD <patricechotard@free.fr>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add some comments about known GPIO settings of supported board
versions.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

After that Anysee I2C adapter is capable of one and two byte long
I2C addresses in case of read from I2C bus.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use correct I2C address for ZL10353 DVB-T demod.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Looks like it is IF route switch on IOE[0]. Set it correctly
to route signal from tuner to demod. Now it works for DVB-C too.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is ZL10353, TDA10023 and TDA18212.
Tuner is inside of Samsung DNOD44CDH086A tuner module.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

New models have new NXP TDA18212 silicon tuner.
Not tested yet due to lack of HW...
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use board ID as base value when selecting correct hardware configuration.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Print firmware version as two digit long (change from 3 to 2).
Windows app have changed that too. First byte was hard coded as 0.

Change email list address to report non-working device to current one.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It can read more than one byte from I2C bus. Allow that.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Switch from 8 bit notation to real 7 bit.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

New silicon tuner driver.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make a user visible driver version change, for the inevitable user support
questions about why newer model HVR-1600's do not work with (older
versions of) the cx18 driver.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A previous changes which added the newer model HVR-1600's and DTV support for
them, neglected to add RF analog TV for them.  Fix RF analog TV for the newer
HVR-1600's which have a worldwide analog tuner assembly with a TDA18271 tuner
and TDA8295 demodulator.

Thanks go to Jeff Campbell and Mike Bradley for reproting the problem, and
also to Mike Bradley for doing a lot of the legwork to figure out the tuner
reset GPIO line, the demodulator I2C address, and that the GPIOs have to be
reinitialized after a cardtype switch.
Reported-by: NJeff Campbell <jac1dlists@gmail.com>
Tested-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This was replaced by Micronas drxd driver
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are still lots of 80-columns warnings and a few errors
at some tables, but changing them would require more work and
with probably not much gain.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The macro is defined as:
	#define CHK_ERROR(s) if( (status = s)<0 ) break

This sucks, as makes harder to debug if something got wrong and
there are more than one level of loops. Also, violates CodingStyle.

Fixed by this simple perl script:

	while (<>) { $f.=$_; };

	$f=~ s,\n\#define CHK_ERROR[^\n]+\n,\n,;

	$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
	$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
	$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
	$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
	$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
	$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;

	$f=~ s,\n(\t+)CHK_ERROR\((.*)\)\;,\n\1status = \2;\n\1if (status < 0)\n\1\tbreak;,g;

	print $f;

Plus a few manual adjustments
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This file is big. It has 12000+ lines! Most of the defined stuff aren't
used anyware inside the driver, so we can just remove most of the lines
and still keep everything that have any interest for the driver.

If anyone ever need the other devices, it will be stored at git logs, so
it is easy to recover.

The diff result is impressive:
 1 files changed, 1013 insertions(+), 12694 deletions(-)
 rewrite drivers/media/dvb/frontends/drxd_map_firm.h (90%)

As a sideback effect, drxd driver will likely compile faster, and
checkpatch.pl can run on this file without taking (literally) hours.

The code cleanup was done using this small script:
	$ for i in `perl -ne 'print "$1\n" if (m/define\s+([^\s+]+)/)' drxd_map_firm.h`; do if [ "`grep $i drivers/media/dvb/frontends/drxd*.[ch]`" != "" ] ; then echo $i; fi; done|sort|uniq >used_symbols
	$ grep -f used_symbols drxd_map_firm.h >defines

And then deleting the old #define lines, replacing by "defines" file content.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s/(define\s+[^\s]+)\s........../\1/
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Take a first cleanup pass over the sources to bring them closer to the
Linux coding style.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>