- 04 2月, 2014 15 次提交
-
-
由 Simon Horman 提交于
The kzm9d board uses has an SMSC911X ethernet controller which uses an SMSC phy. Select SMSC_PHY for kzm9d if SMSC911X is enabled to make use of the SMSC-specific phy driver rather than relying on the generic phy driver. This only covers the case of multiplatform kzm9d as there is currently no Kconfig node for non-multiplatform kzm9d. One could be added if desired. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
The armadillo800eva board uses has an SH ethernet controller which uses an SMSC phy. Select SMSC_PHY for koelsch if SH_ETH is enabled to make use of the SMSC-specific phy driver rather than relying on the generic phy driver. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
The ape6evm board uses has an SMSC911X ethernet controller which uses an SMSC phy. Select SMSC_PHY for ape6evm if SMSC911X is enabled to make use of the SMSC-specific phy driver rather than relying on the generic phy driver. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Valentine Barshak 提交于
This adds SATA0 support to Koelsch board. SATA1 is not available since its pinmux configuration is fixed to PCIe. Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com> Acked-by: NMagnus Damm <damm@opensource.se> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Valentine Barshak 提交于
This adds SATA support to Lager board. Only SATA1 port is available. Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com> Acked-by: NMagnus Damm <damm@opensource.se> [horms+renesas@verge.net.au: resolved trivial conflicts] [horms+renesas@verge.net.au: capitalised "ARM" in subject] Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Takashi Yoshii 提交于
Use common clock framework version of clock drivers/clk/shmobile/clk-emev2.c instead of sh-clkfwk version arch/arm/mach-shmobile/clock-emev2.c when it is configured as a part of multi-platform. Signed-off-by: NTakashi Yoshii <takasi-y@ops.dti.ne.jp> Acked-by: NMagnus Damm <damm@opensource.se> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Valentine Barshak 提交于
This adds VIN1 SoC camera along with ADV7180 subdevice support to Lager. VIN0 camera is not registered because it has ADV7612 I2C subdevice which is not supported yet. Changes in V2: * made lager_add_vin_device function static. Changes in V3: * capitalized ARM in the subject. Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Ulrich Hecht 提交于
Adds support to run the kernel on the uninitialized KZM9G board, using for instance the mask ROM boot loader or JTAG. This patch tries to emulate the style of the corresponding "mackerel" implementation. The DRAM controller setup code has been adapted from u-boot. Signed-off-by: NUlrich Hecht <ulrich.hecht@gmail.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
The koelsch board uses has an SH ethernet controller which uses a Micrel phy. Select MICREL_PHY for koelsch if SH_ETH is enabled to make use of the Micrel-specific phy driver rather than relying on the generic phy driver. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
R-Car sound driver is supporting Mem <-> SRU <-> SSI transfer via DMAEngine. The sound will be less noise if it uses SRU path since it has FIFO. This patch supports it. Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
R-Car sound driver is supporting Mem <-> SSI direct transfer via DMAEngine. Current HPB-DMA is using double plane transfer, but the sound may have noise since SSI doesn't have FIFO. This patch supports it. Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Now that support for KSZ8041RNLI is added to the Micrel PHY driver and we intend to support PHY IRQs on the Lager board, we have to enable the Micrel driver. Do this by selecting CONFIG_MICREL_PHY for Lager if CONFIG_SH_ETH is enabled. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
- 06 1月, 2014 1 次提交
-
-
由 Valentine Barshak 提交于
This fixes the issue introduced by the following commit: b448c904 "ARM: shmobile: r8a7790: add I2C support" The R8A7790 is an R-Car Gen2 SoC. The clock division factor (CDF) width is 3 bits on Gen2 as opposed to 2 bits on Gen1. Fix the device names for R8A7790 SoC to make the R-Car I2C driver configure the hardware properly. Changes in V2: * rebased on top of the latest branch; * capitalized ARM in the subject line; * noted the commit that caused the issue in the log. Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com> Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
- 26 12月, 2013 3 次提交
-
-
由 Laurent Pinchart 提交于
Commit 4dcfa600 ("ARM: DMA-API: better handing of DMA masks for coherent allocations") added an additional check to the coherent DMA mask that results in an error when the mask is larger than what dma_addr_t can address. Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix the problem. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Commit 4dcfa600 ("ARM: DMA-API: better handing of DMA masks for coherent allocations") added an additional check to the coherent DMA mask that results in an error when the mask is larger than what dma_addr_t can address. Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix the problem. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Commit 4dcfa600 ("ARM: DMA-API: better handing of DMA masks for coherent allocations") added an additional check to the coherent DMA mask that results in an error when the mask is larger than what dma_addr_t can address. Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix the problem. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
- 24 12月, 2013 21 次提交
-
-
由 Wolfram Sang 提交于
Tested with RIIC2 on a genmai board. Others untested but hopefully trivial enough to be added. Signed-off-by: NWolfram Sang <wsa@sang-engineering.com> Acked-by: NMagnus Damm <damm@opensource.se> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The field will be removed from the sh-sci driver. Don't set it and let the driver handle baud rate calculation internally. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The field will be removed from the sh-sci driver. Don't set it and let the driver handle baud rate calculation internally. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The field will be removed from the sh-sci driver. Don't set it and let the driver handle baud rate calculation internally. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The field will be removed from the sh-sci driver. Don't set it and let the driver handle baud rate calculation internally. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The field will be removed from the sh-sci driver. Don't set it and let the driver handle baud rate calculation internally. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The field will be removed from the sh-sci driver. Don't set it and let the driver handle baud rate calculation internally. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The field will be removed from the sh-sci driver. Don't set it and let the driver handle baud rate calculation internally. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The field will be removed from the sh-sci driver. Don't set it and let the driver handle baud rate calculation internally. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Passing the register base address and IRQ through platform data is deprecated. Use resources instead. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Passing the register base address and IRQ through platform data is deprecated. Use resources instead. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Passing the register base address and IRQ through platform data is deprecated. Use resources instead. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The field will be removed from the sh-sci driver. Don't set it and let the driver handle baud rate calculation internally. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Passing the register base address and IRQ through platform data is deprecated. Use resources instead. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Passing the register base address and IRQ through platform data is deprecated. Use resources instead. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Passing the register base address and IRQ through platform data is deprecated. Use resources instead. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Passing the register base address and IRQ through platform data is deprecated. Use resources instead. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Passing the register base address and IRQ through platform data is deprecated. Use resources instead. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
Passing the register base address and IRQ through platform data is deprecated. Use resources instead. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The SCIF driver is transitioning to platform resources. Board code will thus need to define an array of resources for each SCIF device. This is incompatible with the macro-based SCIF platform data definition as an array. Rework the macro to define platform data as individual structures. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Laurent Pinchart 提交于
The SCIF driver is transitioning to platform resources. Board code will thus need to define an array of resources for each SCIF device. This is incompatible with the macro-based SCIF platform data definition as an array. Rework the macro to define platform data as individual structures. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-