HIF was not stopped properly in
ath10k_core_start() upon failure. This could cause
memory leaks of CE completions entries and
possibly other issues as well.

Move the HIF start/stop out of
ath10k_htc_wait_target(). The ctl_resp completion
is already prepared in ath10k_htc_init.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This should make sure the device won't issue any
interrupts nor access any memory after the driver
is stopped/freed thus avoid memory corruption in
some cases.
Reported-By: NBen Greear <greearb@candelatech.com>
Reported-By: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add missing error reporting and adjust other
prints to make everything more consistent.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch moves irq registering after necessary
structures have been allocated and initialized.
This should prevent interrupts from causing
tasklet access invalid memory pointers.
Reported-By: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case firmware crashes it may report CE
completions for entries that were never
submitted/filled with meaningful data. This in
turn led to NULL dereferences.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This shouldn't be silenced. This will be necessary
for PCI init code reordering.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This removes some remaining direct use of the wake
register which could interfere with power state
tracking of the target device. This will allow
initialization code reordering.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The check doesn't make much sense. If the address
were to be 0x0000 the check would fail. In this
case a 0 address isn't wrong.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make sure to put target back to sleep. This was a
minor issue as it didn't really matter if we put
target back to sleep at this point. It just looked
wrong.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

CE error interrupts were not disabled. This could
lead to invalid memory accesses / memory
corruption.

Also make sure CE watermark interrupts are also
disabled.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

What the function does is to actually wait for the
firmware indication bit to be set. Prerequisite
for this is having interrupts registered.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The function will soon be called from more than 1
place.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was possible for FW error tasklet to be
executed during teardown. This could lead to
system crashes and/or memory corruption.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It wasn't really useful to have it to begin with.
This makes it a little simpler to re-arrange PCI
init code as some function depended on
ar_pci->ce_count being set.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Not all errors were properly notified, fix that.

kvalo: use ath10k_warn() for all messages, cosmetic changes to some of the messages
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If the 'ar' registration fails early, the debug
objects were not initialized, and trouble ensued when
the object was later destroyed and the un-initialized
objects were accessed.

Per Kalle's suggestion, move the debug_destroy to the
core_unregister method.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

memory is malloced in ath10k_pci_probe() and should be freed before
leaving from the error handling cases, otherwise it will cause
memory leak.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If beacon tx command failed the wmi command buffer
was not freed. This led to OOM in the long run.
This became aparent when stress testing
multi-BSSID.
Reported-By: NTomasz Skapski <tomasz.skapski@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

sk_buff was not freed in some cases. The patch
unifies the msdu freeing.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This allows txpower limits other than regulatory
to be applied (e.g. user txpower limit provided
via iw/nl80211).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was previously thought that FW expects tx power
in quarters of dBm.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will be needed for proper support of (user)
configurable tx power level.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If the creation fails, this keeps us from crashing later when
trying to do a list_del(arvif->list).
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_pci_wait() didn't notify any errors to callers, it
just printed a warning so add proper error handling. This fixes
a crash Ben reported:

ath10k: MSI-X interrupt handling (8 intrs)
ath10k: Unable to wakeup target
ath10k: target took longer 5000 us to wake up (awake count 1)
ath10k: Failed to get pcie state addr: -16
ath10k: early firmware event indicated
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffffa06ae46c>] ath10k_ce_completed_send_next+0x47/0x122 [ath10k_pci]
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.1.389 firmware has some differences in
calculation of number of outstanding HTT TX
completions. This led to FW crashes of 10.1.389
while main firmware branch was unnaffected.

The patch makes sure ath10k doesn't queue up more
MSDUs than it should.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To make it easier to access SOC registers. No functional
changes.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If firmware crashes during FW probing it would try
to perform FW recovery which uses mac80211
workqueue before registering to mac80211.

Using internal workqueue solves the problem.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

NSTS values reported in the VHT-SIG-A1 are 0
through 7 but they actually describe number of
streams 1 through 8.

1SS frames were dropped. This patch fixes this.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes incorrect values being printed on
big-endian hosts.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add a few checks and warnings to make it easier to
track any kind of monitor vdev mismanagement.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes issue with interface bridging.

Linux bridging sets promiscuous mode for all
interfaces that are in a bridge. This translates
to configure_filter() being called in a mac80211
driver.

Before the patch operational interface would be
started and upped again when promiscuous mode was
enabled causing all sorts of strange issues:

 * no HTT RX happening (i.e. no traffic)
 * FW crash upon driver reload/unload
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PCI and SoC specific drivers are using separate
code now so it is not reasonable to use the same
module for both drivers anymore.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'rt2800pci_hwcrypt_disabled' function is the
only PCI specific callback which is used by the
SoC driver. Create a clone of that to get rid of
the dependency.

Even though the two functions are using the same
variable, but the SoC specific code will be moved
into a separate module which will have its own
'modparam_nohwcrypt' variable.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the function into the rt2800mmio module, in order
to make it usable from other modules.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function is called for PCI and SoC devices
however the MCU related part of the function
has no effect on SoC devices. Move the common
part of the function into a separate helper and
use that for the SoC devices.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function contain code for SoC devices only.
Rename the function to 'rt2800soc_disable_radio'
and move it to the SoC specific section. Use
the renamed function in the SoC specific code
only and remove the 'if rt2x00_is_soc(rt2x00dev)'
condition from the function body.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'rt2800pci_set_state' function uses MCU commands
to set the device state, however these have no effect
on SoC devices. Use a different set_state callback
which does not use the MCU fcuntions.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use empty firmware callbacks for SoC devices because those
don't require firmware.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename the 'rt2800pci_read_eeprom_soc function' to
'rt2800soc_read_eeprom' and use that directly in the
SoC specific 'rt2800_ops' structure. Also move the
'rt2800pci_eeprom_read' function into an 'ifdef PCI'
section and remove the 'rt2800pci_read_eeprom_soc'
call from that.

Additionally, remove the dummy inline eeprom functions.
Those are not used anymore.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>