Due to miscalculation of nvs_len, excessive data was sent to the
firmware.
Fix this by first setting nvs_ptr to point to the first NVS table,
and computing the total size of all NVS tables accordingly.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Tested-By: NTuomas Katila <ext-tuomas.2.katila@nokia.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Helps with debugging virtual interfaces.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch ensures fair beacon distribution in IBSS mode
by configuring proper CWmin based on slot time.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Paprd needs to be done only on active chains(not for all the chains
that hw can support). The paprd training frames which are sent
for inactive chains would be hanging on the hw queue without
getting transmitted and would make the connection so unstable.
This issue happens only with the hw which supports paprd cal(ar9003).
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes stale mac80211_tx_control_flags for
filtered / retried frames.

Because ieee80211_handle_filtered_frame feeds skbs back
into the tx path, they have to be stripped of some tx
flags so they won't confuse the stack, driver or device.

Cc: <stable@kernel.org>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The "basic_rate" module option is not implemented correctly.  If the
rate was set to zero it was supposed to set it to "basic_rate | 0x80".
Unfortunately the check to see if what zero was wrong and it checked
"!ai->config.rates" (which is always false) instead of
"!ai->config.rates[i]".

This option was just used for development and it wasn't documented
anywhere.  Instead of fixing it, we can just remove it.
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IEEE Std 802.11k-2008 added DS Parameter Set information element into
Probe Request frames as an optional information on 2.4 GHz band (and
mandatory, if radio measurements are enabled). This allows APs to
filter out Probe Request frames that may be received from neighboring
overlapping channels and by doing so, reduce the number of unnecessary
frames in the air. Make mac80211 add this IE into Probe Request frames
whenever the channel is known (i.e., whenever hwscan is not used).
Signed-off-by: NJouni Malinen <j@w1.fi>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the TX rate set has been masked, the removed rates can also be
removed from the Supported Rates and Extended Supported Rates IEs in
Probe Request frames.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	drivers/net/wireless/ath/ath5k/base.c
	net/mac80211/main.c

commit 8c0c709e
Author: Johannes Berg <johannes@sipsolutions.net>
Date:   Wed Nov 25 17:46:15 2009 +0100

    mac80211: move cmntr flag out of rx flags

moved the CMTR flag into the skb's status, and
in doing so introduced a use-after-free -- when
the skb has been handed to cooked monitors the
status setting will touch now invalid memory.

Additionally, moving it there has effectively
discarded the optimisation -- since the bit is
only ever set on freed SKBs, and those were a
copy, it could never be checked.

For the current release, fixing this properly
is a bit too involved, so let's just remove the
problematic code and leave userspace with one
copy of each frame for each virtual interface.

Cc: stable@kernel.org [2.6.33+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k can use minstrel_ht instead, so it makes sense to save some space here.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not used anywhere else and can be made static
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The tid aggregation cleanup is a bit fragile, as it discards failed
subframes in some places, and retransmits them in others. This could
block the cleanup of an existing aggregation session, if a retransmission
for a tid is issued, yet the tid is never scheduled again because of
the cleanup state.

Fix this by getting rid of as many subframes as possible, as early
as possible, and immediately transmitting pending subframes as regular
HT frames instead of waiting for the cleanup to complete.

Drop all pending subframes while keeping track of the Block ACK window
during aggregate tx completion to prevent sending out stale subframes,
which could confuse the receiver side.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A new aggregation session start can be issued by mac80211, even when the
cleanup of the previous session has not completed yet. Since the data structure
for the session is not recreated, this could corrupt the block ack window
and lock up the aggregation session. Fix this by delaying the new session
until the old one has been cleaned up.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no reason to keep pointers to pending tx buffers around, if they're
only used to keep track of which frames are still pending. Use a bitfield
instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

typo - while looking for specific bits we should do a bitwise-AND instead of logical-AND.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

copy the rx_status directly to skb->cb (control buffer) instead of copying
it to a local struct and then copying it again (for each rx packet)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a obvious bug, skb_queue_walk does not
work if the iterator gets removed from the queue.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver has a set of different initvals for 20 MHz
vs dynamic HT2040 operation. Because we can't change
some of the registers "in-flight", the driver needs to
perform a warm reset.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't mark the device as completely dead just yet.
If all goes to plan and carl9170_reboot succeeds
then we can skip the expensive userspace-driven
reinitialization anyway.

And if it doesn't and carl9170_reboot fails,
then carl9170_usb_cancel_urbs will do the
necessary steps.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch prevents the tasklet code from
interfering while the firmware is down for
an unscheduled maintenance.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to Atheros, chain 1 is not connected.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ever since carl9170 gained support to read the noisefloor,
the reported noisefloor level was pretty poor.

Initially I assumed that something was wrong in the PHY
setup and it would be impossible to fix without any
guidances. But this was not the case. In fact the nf
readings were correct and the thing that was broken
was the "simple" sign extension code!
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The eeprom provides a mask for all present rx chains.
Why not use it instead of the generic initval default?
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the mac80211 callback function to configure the tx queue properties like
cw_min, cw_max and aifs.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Get rid of overly complicated cw_min/max and AIFS configuration:

* Validate values in ath5k_hw_set_tx_queueprops(), so we can use them directly
  without further checks or computation in ath5k_hw_reset_tx_queue().

* Simplifiy by using AR5K_TUNE_AIFS|CWMIN|CWMAX variables directly since we
  don't support XR or B channels. That way we can also remove
  AR5K_TXQ_USEDEFAULT and the confusing logic around it.

* Update data types: AIFS is u8, CW's are u16.

* Remove now unneeded variables in ath5k_hw.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we return a TX descriptor to the pool of available descriptors, while a
queues TXDP still points to it we could potentially run into all sorts of
troube.

It has been suggested that there is hardware which can set the descriptors
done bit before it reads ds_link and moves on to the next descriptor. While the
documentation says this is not true for newer chipsets (the descriptor contents
are copied to some internal memory), we don't know about older hardware.

To be safe, we always keep the last descriptor in the queue, and avoid dangling
TXDP pointers. Unfortunately this does not fully resolve the problem - queues
still get stuck!

This is similar to what ath9k does.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a counter to show how many times a queue got stuck in the debugfs queue
file.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we do not know any better solution to the problem that TX queues can get
stuck, this adds a timer-based watchdog, which will check for stuck queues and
reset the hardware if necessary.

Ported from ath9k commit 164ace38.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clearer separation between queue handling and what we do with completed frames.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It does not make sense to stop queues for NF calibration. This will not stop
transmissions from the card, if there are queued packets.

If we run out of TX buffers we need to stop all queues, not only one.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Take txq lock in debug file and fix reporting of used buffers.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prepare ath5k for WME by using four hardware queues.

The way we set up our queues matches the mac80211 queue priority 1:1, so we
don't have to do any mapping for queue numbers.

Every queue uses 50 of the total 200 available transmit buffers, so the DMA
memory usage does not increase with this patch, but it might be good to
fine-tune the number of buffers per queue later (depending on the CPU speed and
load, and the speed of the medium access, it might not be big enough).
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change reorganizes the main ath5k file in order to re-group
related functions and remove most of the forward declarations
(from 61 down to 3).  This is, unfortunately, a lot of churn, but
there should be no functional changes.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixing up a merge issue / concurrent development:

Remove unneeded ath_crypt_caps flags, as per "ath9k_hw: remove useless hw
capability flags" (364734fa), but set the
AESCCM flag for ath9k. common ath code still needs a flag for this because
there is ath5k hardware which can't do AES in hardware.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is loosely based on an ath9k patch called:
"ath9k_hw: sync initvals for ar9001 and ar9002 with Atheros"

It includes the following changes/fixes:
	- AGC setting improvements
	- timing changes for improved performance
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add MMC3 support on ZOOM, which has the wl1271 device hardwired to.

The wl1271 is a 4-wire, 1.8V, embedded SDIO WLAN device with an
external IRQ line, and power-controlled by a GPIO-based fixed regulator.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a fixed regulator vmmc device to enable power control
of the wl1271 wlan device.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wl1271 device is using a reference clock that may change
between board to board.

Make the ref_clock parameter configurable by board settings
instead of having a hard coded value in the sources.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the hard coded irq information, and instead take
the irq information from the board's platform data.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>