This patch (as1165) makes a few small changes in the logic used by
ehci-hcd when it encounters a controller error:

	Instead of printing out the masked status, it prints the
	original status as read directly from the hardware.

	It doesn't check for the STS_HALT status bit before taking
	action.  The mere fact that the STS_FATAL bit is set means
	that something bad has happened and the controller needs to
	be reset.  With the old code this test could never succeed
	because the STS_HALT bit was masked out from the status.

I anticipate that this will prevent the occasional "irq X: nobody cared"
problem people encounter when their EHCI controllers die.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When I used SuperH on-chip USB, there was the problem that accessed
r8a66597_root_hub which was not allocated.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Due to recent changes to usb_reset_device, the following hang occurs:

events/0      D 0000000000000000     0     6      2
 ffff880037477cc0 0000000000000046 ffff880037477c50 ffffffff80237434
 ffffffff80574c80 00000001000a015c 0000000000000286 ffff8800374757d0
 ffff88002a31c860 ffff880037475a00 0000000036779140 ffff880037475a00
Call Trace:
 [<ffffffff80237434>] try_to_del_timer_sync+0x52/0x5b
 [<ffffffff8026f86c>] dma_pool_free+0x1a7/0x1ec
 [<ffffffffa02a928a>] ub_disconnect+0x8e/0x1ad [ub]
 [<ffffffff802407c9>] autoremove_wake_function+0x0/0x2e
 [<ffffffff80378959>] usb_unbind_interface+0x5c/0xb7
 [<ffffffff8036ab70>] __device_release_driver+0x95/0xbd
 [<ffffffff8036ac70>] device_release_driver+0x21/0x2d
 [<ffffffff803789f8>] usb_driver_release_interface+0x44/0x83
 [<ffffffff80378ab9>] usb_forced_unbind_intf+0x17/0x1d
 [<ffffffff80371ba4>] usb_reset_device+0x7d/0x114
 [<ffffffffa02aaffd>] ub_reset_task+0x0/0x293 [ub]
 [<ffffffffa02ab1c1>] ub_reset_task+0x1c4/0x293 [ub]
 [<ffffffff8033dd1e>] flush_to_ldisc+0x0/0x1cd
 [<ffffffffa02aaffd>] ub_reset_task+0x0/0x293 [ub]
 [<ffffffff8023d302>] run_workqueue+0x87/0x114
 [<ffffffff8023d467>] worker_thread+0xd8/0xe7
 [<ffffffff802407c9>] autoremove_wake_function+0x0/0x2e
 [<ffffffff8023d38f>] worker_thread+0x0/0xe7
 [<ffffffff802404c1>] kthread+0x47/0x73
 [<ffffffff8022c8dd>] schedule_tail+0x27/0x60
 [<ffffffff8020c249>] child_rip+0xa/0x11
 [<ffffffff8024047a>] kthread+0x0/0x73
 [<ffffffff8020c23f>] child_rip+0x0/0x11

This is because usb_reset_device now unbinds, and that calls disconnect,
which in case of ub waits until the reset completes... which deadlocks.
Worse, this deadlocks keventd and this takes whole box down.

I'm going to fix this properly later, but let's unbreak the driver
quickly for non-composite devices at least.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlbert Comerma <albert.comerma@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Additional sectors were reported by the Nokia 7610 Supernova phone in
usb storage mode. The following patch rectifies the aforementioned
problem.
Signed-off-by: NRicky Wong Yung Fei <evilbladewarrior@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Roland Reported the following:
| kmem_cache_create: duplicate cache isp1760_qtd
| Pid: 461, comm: modprobe Tainted: G        W  2.6.28-rc2-git3-default #4
| Call Trace:
|  [<c017540e>] kmem_cache_create+0xc9/0x3a3
|  [<c0159a8d>] free_pages_bulk+0x16c/0x1c9
|  [<f165c05f>] isp1760_init+0x0/0xb [isp1760]
|  [<f165c018>] init_kmem_once+0x18/0x5f [isp1760]
|  [<f165c064>] isp1760_init+0x5/0xb [isp1760]
|  [<c010113d>] _stext+0x4d/0x148
|  [<c0142936>] load_module+0x12cd/0x142e
|  [<c01743c4>] kmem_cache_destroy+0x0/0xd7
|  [<c0142b1e>] sys_init_module+0x87/0x176
|  [<c01039eb>] sysenter_do_call+0x12/0x2f

The reason, is that ret is initialized with ENODEV instead of 0 _or_
the kmem cache is not freed in error case with no bus binding.

The difference between OF+PCI and OF only is
| 15148     804      32   15984    3e70 isp1760-of-pci.o
| 13748     676       8   14432    3860 isp1760-of.o

about 1.5 KiB.

Until there is a checkbox where the user *must* select atleast one item,
and may select multiple entries I don't make it selectable anymore.
Having a driver which can't be used under any circumstances is broken
anyway and I've seen distros shipping it that way.
Reported-by: NRoland Kletzing <devzero@web.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>a
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Enfora GSM2228 based on Cygnal Integrated Products chip uses the same
cp2101 driver.
Signed-off-by: NDamir N Abdullin <damir@mimas.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since commit 65934a9a ("Make USB storage depend on SCSI rather than selecting
it [try #6]") the comment at the top of drivers/usb/storage/Kconfig is
incorrect. Adjust it to the current situation.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ehci_shutdown() or ohci_shutdown() calls to the USB
PS3 bus glue.  ehci_shutdown() and ohci_shutdown() do some
controller specific cleanups not done by usb_remove_hcd().

Fixes errors on shutdown or reboot similar to these:

  ps3-ehci-driver sb_07: HC died; cleaning up
  irq 51: nobody cared (try booting with the "irqpoll" option)

Related bugzilla reports:

  http://bugzilla.kernel.org/show_bug.cgi?id=11819
  http://bugzilla.terrasoftsolutions.com/show_bug.cgi?id=317Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1162) adds an unusual_devs entry for Argosy's USB-IDE
interface.  This fixes Bugzilla #11843.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NLuciano Rocha <luciano@eurotux.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes an obvious bug in cdc-acm by avoiding a recursive lock on
acm_start_wb()'s error path. Should apply towards 2.6.27 stable and
2.6.28.

=============================================
[ INFO: possible recursive locking detected ]
2.6.27-2-pae #109
---------------------------------------------
python/31449 is trying to acquire lock:
 (&acm->write_lock){++..}, at: [<f89a0348>] acm_start_wb+0x5c/0x7b [cdc_acm]

but task is already holding lock:
 (&acm->write_lock){++..}, at: [<f89a04fb>] acm_tty_write+0xe1/0x167 [cdc_acm]

other info that might help us debug this:
2 locks held by python/31449:
 #0:  (&tty->atomic_write_lock){--..}, at: [<c0260fae>] tty_write_lock+0x14/0x3b
 #1:  (&acm->write_lock){++..}, at: [<f89a04fb>] acm_tty_write+0xe1/0x167 [cdc_acm]

stack backtrace:
Pid: 31449, comm: python Not tainted 2.6.27-2-pae #109
 [<c030f42f>] ? printk+0xf/0x18
 [<c0149f33>] __lock_acquire+0xc7b/0x1316
 [<c014a63e>] lock_acquire+0x70/0x97
 [<f89a0348>] ? acm_start_wb+0x5c/0x7b [cdc_acm]
 [<c0312109>] _spin_lock_irqsave+0x37/0x47
 [<f89a0348>] ? acm_start_wb+0x5c/0x7b [cdc_acm]
 [<f89a0348>] acm_start_wb+0x5c/0x7b [cdc_acm]
 [<f89a055d>] acm_tty_write+0x143/0x167 [cdc_acm]
 [<c0262a98>] write_chan+0x1cd/0x297
 [<c012527e>] ? default_wake_function+0x0/0xd
 [<c026111e>] tty_write+0x149/0x1b9
 [<c02628cb>] ? write_chan+0x0/0x297
 [<c01912c5>] ? rw_verify_area+0x76/0x98
 [<c0260fd5>] ? tty_write+0x0/0x1b9
 [<c01919ba>] vfs_write+0x8c/0x136
 [<c0191afd>] sys_write+0x3b/0x60
 [<c0103beb>] sysenter_do_call+0x12/0x3f
 =======================
Signed-off-by: NBrandon Philips <bphilips@suse.de>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the device vendor and product IDs for Amber Wireless AMB2560
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb_free_urb comment says that the transfer buffer will not be
freed, but this is not the case when URB_FREE_BUFFER is set.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds YISO u893 usb modem vendor and product ID to option.c.

I had a better experience using this modification and the same system.
Signed-off-by: NLeslie Harlley Watter <leslie@watter.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes co-working issue of usb serial device with usb/net devices while
oter endpoints are free and can be used.This patch implements the policy
that if endpoint resources are available then different BULK request goes
to different endpoint otherwise they are multiplexed to one reserved
endpoint as currently done.

Switch statement case is reordered in musb_giveback() to take care of
bulk request both in multiplex scenario and otherwise.

NAK limit scheme has to be added for multiplexed BULK request scenario
to avoid endpoint starvation due to usb/net devices.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In order to avoid namespace conflicts, add a prefix
to our kernel-wise symbol.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes compilation warning when musb is configured in gadget mode.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add an errno to failing case.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes blurred capture images in dma mode. Isochronous error field in
urb and source data buffer pointer were not updated properly in dma
mode.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1155) fixes a bug in usbcore.  When interfaces are
deleted, either because the device was disconnected or because of a
configuration change, the extra attribute files and child endpoint
devices may get left behind.  This is because the core removes them
before calling device_del().  But during device_del(), after the
driver is unbound the core will reinstall altsetting 0 and recreate
those extra attributes and children.

The patch prevents this by adding a flag to record when the interface
is in the midst of being unregistered.  When the flag is set, the
attribute files and child devices will not be created.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.27, 2.6.26, 2.6.25]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11685

When A Nikon D300 camera is connected to a system it is seen in
/proc/bus/pci/devices but is not accessible.

This is seen in the above file:

T:  Bus=01 Lev=01 Prnt=01 Port=05 Cnt=03 Dev#= 11 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=04b0 ProdID=041a Rev= 1.03
S:  Manufacturer=NIKON
S:  Product=NIKON DSC D300
S:  SerialNumber=000008014379
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  2mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=06(still) Sub=01 Prot=01 Driver=usbfs
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   8 Ivl=32ms

Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a reported compiler warning.
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: ignore bit0 of _OSC return code

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
  dlm: fix shutdown cleanup

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slab: document SLAB_DESTROY_BY_RCU
  Kconfig: SLUB is the default slab allocator

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] cdb89712: avoid namespace clashes with SRAM_ and BOOTROM_ constants
  [ARM] cdb89712,clps7500,h720x: avoid namespace clash for FLASH_* constants
  [ARM] integrator,realview,versatile: remove FLASH_* and EPROM_* constants
  [ARM] dma-mapping: fix compiler warning
  [ARM] iop: iop3xx needs registers mapped uncached+unbuffered
  [ARM] versatile: correct MMC clock rate
  [ARM] realview: correct MMC clock rate
  [ARM] 5329/1: Feroceon: fix feroceon_l2_inv_range

Commit 2d3854a3 ("cpumask: introduce new
API, without changing anything") introduced a build breakage on parisc.

This trivial patch fixes it.
Signed-off-by: NHelge Deller <deller@gmx.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kyle Mc Martin <kyle@hera.kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes a regression from commit 0f8e0d9a,
"dlm: allow multiple lockspace creates".

An extraneous 'else' slipped into a code fragment being moved from
release_lockspace() to dlm_release_lockspace().  The result of the
unwanted 'else' is that dlm threads and structures are not stopped
and cleaned up when the final dlm lockspace is removed.  Trying to
create a new lockspace again afterward will fail with
"kmem_cache_create: duplicate cache dlm_conn" because the cache
was not previously destroyed.
Signed-off-by: NDavid Teigland <teigland@redhat.com>

Explain this SLAB_DESTROY_BY_RCU thing...

[hugh@veritas.com: add a pointer to comment in mm/slab.c]
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NChristoph Lameter <cl@linux-foundation.org>
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>

In 2007, a0acd820 changed the default
slab allocator to SLUB, but the SLAB help text still says SLAB is the
default. This change fixes that.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

FLASH_* and EPROM_* constants are unused, and clash with drivers:

drivers/atm/ambassador.h:257:1: warning: "FLASH_BASE" redefined
drivers/atm/ambassador.h:258:1: warning: "FLASH_SIZE" redefined
drivers/atm/iphase.h:332:1: warning: "EPROM_SIZE" redefined

so remove them.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mm/dma-mapping.c: In function `dma_sync_sg_for_cpu':
arch/arm/mm/dma-mapping.c:588: warning: statement with no effect
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: fix init_idle()'s use of sched_clock()
  sched: fix stale value in average load per task

Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

C2port implements a two wire serial communication protocol (bit
banging) designed to enable in-system programming, debugging, and
boundary-scan testing on low pin-count Silicon Labs devices.

Currently this code supports only flash programming through sysfs
interface but extensions shoud be easy to add.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a brief document about omap2430/3430 HDQ/1-wire driver.

Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide the BQ27000 slave interface driver.

Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
protocol of the master functions of the Benchmark HDQ and the Dallas
Semiconductor 1-Wire protocols.  These protocols use a single wire for
communication between the master (HDQ/1-Wire controller) and the slave
(HDQ/1-Wire external compliant device).

This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms.

Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>