Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

EBSA110 only requires hardware.h to be included for a couple of
files.  Move the include there.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The mpic interrupt controller driver (used on G5 and early pSeries among
others) has a bug where it doesn't get the right virtual address for the
timer registers.  It causes the driver to poke at the MMIO space of
whatever has been mapped just next to it (ouch !) when initializing and
causes boot failures on some IBM machines.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes compile problem when CONFIG_FB_PXA is not set.

  LD      .tmp_vmlinux1
arch/arm/mach-pxa/built-in.o(.text+0x1d74): In function
`spitz_get_hsync_len':
: undefined reference to `pxafb_get_hsync_time'
make: *** [.tmp_vmlinux1] Error 1
3.46user 0.46system 5.10 (0m5.106s) elapsed 77.01%CPU
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Without this patch, uml compile fails with:

  LD      .tmp_vmlinux1
arch/um/kernel/built-in.o: In function `config_gdb_cb':
arch/um/kernel/tt/gdb.c:129: undefined reference to `TASK_EXTERN_PID'

Tested on i386, but fix needed on x86_64 too AFAICS.
Signed-off-by: NMiklos Szeredi <miklos@szeredi.hu>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Not sure how it slipped by, but here's a trivial typo fix for powernow.
Signed-off-by: NChris Wright <chrisw@osdl.org>
[ It's "nurter" backwards.. Maybe we have a hillbilly The Shining fan? ]
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

AMD recently discovered that on some hardware, there is a race condition
possible when a C-state change request goes onto the bus at the same
time as a P-state change request.

Both requests happen, but the southbridge hardware only acknowledges the
C-state change.  The PowerNow! driver is then stuck in a loop, waiting
for the P-state change acknowledgement.  The driver eventually times
out, but can no longer perform P-state changes.

It turns out the solution is to resend the P-state change, which the
southbridge will acknowledge normally.

Thanks to Johannes Winkelmann for reporting this and testing the fix.
Signed-off-by: NMark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes a stupid typo bug in the iSeries hash table code.

When we place a hash PTE in the secondary bucket, instead of setting the
SECONDARY flag bit, as we should, we (redundantly) set the VALID flag.

This was introduced with the patch abolishing bitfields from the hash
table code.  Mea culpa, oops.  It hasn't been noticed until now because
in practice we don't hit the secondary bucket terribly often.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

While working on 64K pages, I found this little buglet in our
update_mmu_cache() implementation.

The code calls __hash_page() passing it an "access" parameter (the type
of access that triggers the hash) containing the bits _PAGE_RW and
_PAGE_USER of the linux PTE.  The latter is useless in this case and the
former is wrong.  In fact, if we have a writeable PTE and we pass
_PAGE_RW to hash_page(), it will set _PAGE_DIRTY (since we track dirty
that way, by hash faulting !dirty) which is not what we want.

In fact, the correct fix is to always pass 0. That means that only
read-only or already dirty read write PTEs will be preloaded. The
(hopefully rare) case of a non dirty read write PTE can't be preloaded
this way, it will have to fault in hash_page on the actual access.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes a typo in the div128_by_32 function used in the timekeeping
calculations on ppc64.  If you look at the code it's quite obvious
that we need (rb + c) rather than (rb + b).  The "b" is clearly just a
typo.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The current Simtec BAST nand area timings are a little
too slow to be obtained by a 2410 running at 266MHz,
so reduce the timings slightly to bring them into the
acceptable range.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Matt Reimer

Adds an I2S platform_device for PXA. I2S is used to interface
with sound chips on systems like iPAQ h1910/h2200/hx4700 and
Asus 716.

Signed-off-by: mreimer@vpop.net
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

	Missing half of the [PATCH] uml: Fix sysrq-r support for skas mode
We need to remove these (UPT_[DEFG]S) from the read side as well as the
write one - otherwise it simply won't build.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This introduces a limit parameter to the core bootmem allocator; The new
parameter indicates that physical memory allocated by the bootmem
allocator should be within the requested limit.

We also introduce alloc_bootmem_low_pages_limit, alloc_bootmem_node_limit,
alloc_bootmem_low_pages_node_limit apis, but alloc_bootmem_low_pages_limit
is the only api used for swiotlb.

The existing alloc_bootmem_low_pages() api could instead have been
changed and made to pass right limit to the core allocator.  But that
would make the patch more intrusive for 2.6.14, as other arches use
alloc_bootmem_low_pages().  We may be done that post 2.6.14 as a
cleanup.

With this, swiotlb gets memory within 4G for both x86_64 and ia64
arches.
Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The implementation of __kernel_gettimeofday() in the 32 bits vDSO has a
small bug (a typo actually) that will cause it to lose 1 bit of precision.
Not terribly bad but worth fixing.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch from Tony Lindgren

Machine restart calls cpu_proc_fin() to clean and disable
cache, and turn off interrupts. This patch adds proper
cpu_v6_proc_fin.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Check that the device we are looking at is really
a platform device before trying to cast it to one
to find out the platform bus number.

Thanks to RMK for pointing this out.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Andreas Schwab spotted that recent kernels broke reporting of the PowerMac
machine model in /proc/cpuinfo.  This fixes it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes the following BUG message of arch/m32r/smp.c for
CONFIG_DEBUG_PREEMPT:

BUG: using smp_processor_id() in preemptible

This message is displayed by an smp_processor_id() execution during
kernel's preemptible-state.
Signed-off-by: NHitoshi Yamamoto <hitoshiy@isl.melco.co.jp>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

arch/mips/pci/fixup-tb0226.c: In function `pcibios_map_irq':
arch/mips/pci/fixup-tb0226.c:31: warning: implicit declaration of function `vr41xx_set_irq_trigger'
arch/mips/pci/fixup-tb0226.c:32: error: `TRIGGER_LEVEL' undeclared (first use in this function)
arch/mips/pci/fixup-tb0226.c:32: error: (Each undeclared identifier is reported only once
arch/mips/pci/fixup-tb0226.c:32: error: for each function it appears in.)
arch/mips/pci/fixup-tb0226.c:33: error: `SIGNAL_THROUGH' undeclared (first use in this function)
arch/mips/pci/fixup-tb0226.c:34: warning: implicit declaration of function `vr41xx_set_irq_level'
arch/mips/pci/fixup-tb0226.c:34: error: `LEVEL_LOW' undeclared (first use in this function)
Signed-off-by: NYoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Doing a "SUNW,stop-self" firmware call on the other cpus is not the
correct thing to do when dropping into the firmware for a halt,
reboot, or power-off.

For now, just do nothing to quiet the other cpus, as the system should
be quiescent enough.  Later we may decide to implement smp_send_stop()
like the other SMP platforms do.

Based upon a report from Christopher Zimmermann.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patch from Richard Purdie

Remove a couple of lines of accidently added code causing compile
errors.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Richard Purdie

Update corgi_lcd to use bus_find_device to locate the pxafb device
hence fixing a compile error.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Richard Purdie

Add a function to allow machines to set the parent of the pxa
framebuffer device. This means the power up/down sequence can be
controlled where required by the machine.

Update spitz to use the new function, fixing a compile error.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Deepak Saxena

This patch fixes L7200 so that it builds in 2.6.latest. I do not
have the hardware so don't know if it actually still works, but
the changes are fairly trivial. I am not even sure if anyone
still maintains, uses, or cares about this machine type.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The hairy fast allocator in the sparc64 PCI IOMMU code
has a hard limit of 256 pages.  Certain devices can
exceed this when performing very large I/Os.

So replace with a more simple allocator, based largely
upon the arch/ppc64/kernel/iommu.c code.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the PCI controller drivers were doing the same thing
setting up the IOMMU software state, put it all in one spot.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Original patch by Harald Welte, with feedback from Herbert Xu
and testing by Sébastien Bernard.

EBTABLES, ARP tables, and IP/IP6 tables all assume that cpus
are numbered linearly.  That is not necessarily true.

This patch fixes that up by calculating the largest possible
cpu number, and allocating enough per-cpu structure space given
that.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patch from Nicolas Pitre

... and therefore should not live in the .text section.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The Simtec EB2410ITX (BAST) has a PC/104 slot, and
therefore we should enable CONFIG_ISA to allow the
drivers for ISA peripherals to be selected
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Remove an unused variable from s3c2410.c and
ensure that items not needed to be exported from
s3c2440.c are declared static.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sequence to move over to the Linux trap tables from
the firmware ones needs to be more air tight.  It turns
out that to be %100 safe we do need to be able to translate
OBP mappings in our TLB miss handlers early.

In order not to eat up a lot of kernel image memory with
static page tables, just use the translations array in
the OBP TLB miss handlers.  That solves the bulk of the
problem.

Furthermore, to make sure the OBP TLB miss path will work
even before the fixed MMU globals are loaded, explicitly
load %g1 to TLB_SFSR at the beginning of the i-TLB and
d-TLB miss handlers.

To ease the OBP TLB miss walking of the prom_trans[] array,
we sort it then delete all of the non-OBP entries in there
(for example, there are entries for the kernel image itself
which we're not interested in at all).

We also save about 32K of kernel image size with this change.
Not a bad side effect :-)

There are still some reasons why trampoline.S can't use the
setup_trap_table() yet.  The most noteworthy are:

1) OBP boots secondary processors with non-bias'd stack for
   some reason.  This is easily fixed by using a small bootup
   stack in the kernel image explicitly for this purpose.

2) Doing a firmware call via the normal C call prom_set_trap_table()
   goes through the whole OBP enter/exit sequence that saves and
   restores OBP and Linux kernel state in the MMUs.  This path
   unfortunately does a "flush %g6" while loading up the OBP locked
   TLB entries for the firmware call.

   If we setup the %g6 in the trampoline.S code properly, that
   is in the PAGE_OFFSET linear mapping, but we're not on the
   kernel trap table yet so those addresses won't translate properly.

   One idea is to do a by-hand firmware call like we do in the
   early bootup code and elsewhere here in trampoline.S  But this
   fails as well, as aparently the secondary processors are not
   booted with OBP's special locked TLB entries loaded.  These
   are necessary for the firwmare to processes TLB misses correctly
   up until the point where we take over the trap table.

This does need to be resolved at some point.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patch from Ben Dooks

The NWFPE is producing a number of errors from sparse
due to not defining a number of functions in the
header files.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from George G. Davis

Fix leading, trailing and other miscellaneous whitespace issues
in arch/arm/kernel/alignment.c.
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from George G. Davis

When building for CPU_V6 targets, we should use -mtune=arm1136j-s rather
than -mtune=strongarm but fall back to the later in case someone is
using an older toolchain (although they should really upgrade instead).
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Do not export items that are not needed by symbol name
elsewhere
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The items in the export table do not need to be
exported elsehwere, so quash the sparse warning
by making the symbol for the table entry static.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

arch/arm/mach-s3c2410/time.c is missing include
of cpu.h, causing the declaration of the timer
struct (s3c24xx_timer) to be flagged as missing
the declaration.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>