On the at91sam9x5 SoC series, GPIO banks B and D only have 19 and 22
pins. So add a property to set this parameter.
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Fix also the reg size as we have 512 bytes bank not 256 bytes per gpio/mux
controller
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron), McPDM, DMIC, McBSP1 and McBSP2.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

These all use the generic pinctrl-single driver for the padconf registers.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron, irq), McPDM and McBSP1.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron, irq), McPDM, DMIC, McBSP1 and
McBSP2.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McBSP3 is not usable on OMAP4 SDP/Blaze (the pins used for McPDM).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McBSP3 is not usable on OMAP4 SDP/Blaze (the pins used for McPDM).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McBSP2, McBSP3 and DMIC is not usable on PandaBoard (not connected, no
external pins provided for them).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds am335x-evm and am335x-bone dtb targets to
'make dtbs', just like other platforms.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.
Signed-off-by: NMarek Vasut <marex@denx.de>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>

[wsa: rebased to 3.6-rc7]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

This adds simple DT bindings for SDHCI SPEAr controller. It uses cd-gpios
from common mmc bindings.

This also fixes spear300-evb.dts with correct name for card detect binding.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

We already have CONFIG_ARCH_MXC cover imx5 and imx6 dtb targets.
Remove the redundant ones with CONFIG_ARCH_IMX5 and CONFIG_SOC_IMX6Q.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add board files (vt8500-bv07, wm8505-ref and wm8650-mid)
to allow 'make dtbs' on arch-vt8500.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Unit addresses, whilst written in hex, don't contain a 0x prefix.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some highbank DMA masters can support coherent (ACP) or non-coherent DMA.
This sets up dma_map_ops for masters which are configured for coherent DMA.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>

Add device nodes for the four instances of dw_mmc controllers in
EXYNOS5250 and enable instance 0 and 2 for the SMDK5250 board.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adjusts the PHY3250 board file to the actual LED configuration
(active high, default-state and trigger configuration).
Signed-off-by: NRoland Stigge <stigge@antcom.de>

Given that the xenvm machine is based on vexpress but with an extremely
limited selection of peripherals (the guest is supposed to use virtual
devices instead), add "xen,xenvm" to the list of compatible machines in
mach-vexpress.


Changes in v3:

- add comments to mark fields that are likely to be changed by the
hypervisor.


Changes in v2:

- remove include skeleton;
- use #address-cells = <2> and #size-cells = <2>;
- remove the debug bootargs;
- use memory@80000000 instead of memory;
- remove the ranges and interrupt-map from the motherboard node;
- set the machine compatible to "xen,xenvm-4.2", "xen,xenvm";
- rename the dts file to xenvm-4.2.dts;
- add "xen,xenvm" to the list of compatible DT strings to mach-vexpress.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: Pawel Moll <pawel.moll@arm.com> (v2m changes)

This moves a few of the newly introduced dtb targets to the common
dts/Makefile instead of the per-platform file.
Signed-off-by: NOlof Johansson <olof@lixom.net>

The gpioX aliases are needed so that the driver can use
of_alias_get_id() to get a 0-based number of the GPIO bank, which we
then use to compute the base GPIO of the bank being probed. This is
similar to what gpio-mxs.c is doing.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada XP evaluation board is based on the MV78460 Armava XP
SoC. Now that we have separate .dtsi files for the three different
SoCs of the Armada XP family, use the appropriate one as include for
the Armada XP evaluation board .dts file.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This commits adds the necessary device tree information to define the
compatible property for the pinctrl driver instance of Armada 370 SoC.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This commits adds the necessary device tree information to define the
compatible property for the pinctrl driver instance of Armada XP SoCs.

Until now, the device tree representation considered the Armada XP as
a single SoC. But in fact, there are three different SoCs in the
Armada XP families, with different number of CPU cores, different
number of Ethernet interfaces... and different number of muxable pins
or functions. We therefore introduce three armada-xp-mv78xx0.dtsi for
the three SoCs of the Armada XP family. The current armada-xp-db.dts
evaluation board uses the MV78460 variant of the SoC.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Remove more board-specific code by using devicetree to define the fan
attached to both boards.
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Based on work by Michael Walle and Jason Cooper.

Added support for getting the interrupt number and address of SRAM
from DT.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Conflicts:

	arch/arm/mach-kirkwood/board-dt.c

Define the nand and its partitions in DT and remove them from cmdline
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Define the 2 keys found on iconnect in DT. It's also changing the keycodes/
switches to use better ones.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds basic support for the SolidRun CuBox to DT based
mach-dove. There are still some issues related to ongoing orion/mvebu
development, e.g. gpio-led will not work as there is no DT pinctrl
for dove yet and we don't have board specific setup code. Nevertheless,
the DT description is already introduced here.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds device tree decriptors for dove SoC and currently
supported boards.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This is a first attempt to support the km_kirkwood reference design with
a device tree. This km_kirkwood design is present in many Keymile
products. It is based on the Marvell Bobcat SOC which integrates a
Kirkwood CPU next to a big L2 Ethernet Switch. The Kirkwood in the SOC
is very similar to the "normal" one, but there are a few differences.

This initial support is minimal: the kernel can boot with network
(ge0), serial port and NAND functional.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This adds the corresponding device tree descriptor for the
Seagate FreeAgent Dockstar based on Kirkwood DT.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add support for the Iomega ix2-200.
Led's and buttons working as of kernel 3.6-rc2

the 3 lines in the network interface do seem to be required as
removing either causes the network card to not be able to reach
the network (at least on my device).

Product page:
http://go.iomega.com/en/products/network-storage-desktop/storcenter-network-storage-solution/network-hard-drive-ix2-200-cloud/?partner=4735#tech_specsItem_tabSigned-off-by: NAlan M Butler <alanbutty12@gmail.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add device tree files for VT8500, WM8505 and WM8650 SoC's and
reference boards.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>

Since the dtb targets have moved to arch/arm/boot/dts/Makefile, sweep
the platforms that have had new targets added recently and move them over.

While I was at it, I also made the dtb generation more generic, i.e. if
the platform is enabled then all dtbs for that platform will be created.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brown <davidb@codeaurora.com>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>

On Harmony, LDO7 does not feed vdd_fuse. Correct the regulator name.
This issue was probably the result of copying Ventana's regulator setup
when creating the Harmony .dts file. No other naming issues appear to
exist.
Reported-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

On board keys on Origen board can serve as wakeup sources,
hence they are marked accordingly in the device tree file.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Cc: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>