commit 057d476fff778f1d3b9f861fdb5437ea1a3cfc99 upstream.

A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.

When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.

If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.

Example case:
usb_runtime_suspend() # because all ports still show suspended U3
  usb_suspend_both()
    hub_suspend();   # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
  handle_port_status()
    clear bus_state->port_remote_wakeup
    usb_wakeup_notification()
      sets hub->wakeup_bits;
        kick_hub_wq()
<== END INTERRUPT
      hcd_bus_suspend()
        xhci_bus_suspend() # success as port_remote_wakeup bits cleared

Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.

Issue rootcaused by Chiasheng Lee

Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: NLee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 008037d4d972c9c47b273e40e52ae34f9d9e33e7 upstream.

Shift and mask were reversed.  Noticed by chance.
Tested-by: NMeelis Roos <mroos@linux.ee>
Reviewed-by: NMichel Dänzer <mdaenzer@redhat.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 58e39a2ce4be08162c0368030cdc405f7fd849aa upstream.

When a port sends PLOGI, discovery state should be changed to login
pending, otherwise RELOGIN_NEEDED bit is set in
qla24xx_handle_plogi_done_event(). RELOGIN_NEEDED triggers another PLOGI,
and it never goes out of the loop until login timer expires.

Fixes: 8777e431 ("scsi: qla2xxx: Migrate NVME N2N handling into state machine")
Fixes: 8b5292bcfcacf ("scsi: qla2xxx: Fix Relogin to prevent modifying scan_state flag")
Cc: Quinn Tran <qutran@marvell.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191125165702.1013-6-r.bolshakov@yadro.comAcked-by: NHimanshu Madhani <hmadhani@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NRoman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5480e299b5ae57956af01d4839c9fc88a465eeab upstream.

Some time ago the block layer was modified such that timeout handlers are
called from thread context instead of interrupt context. Make it safe to
run the iSCSI timeout handler in thread context. This patch fixes the
following lockdep complaint:

================================
WARNING: inconsistent lock state
5.5.1-dbg+ #11 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/7:1H/206 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff88802d9827e8 (&(&session->frwd_lock)->rlock){+.?.}, at: iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
{IN-SOFTIRQ-W} state was registered at:
  lock_acquire+0x106/0x240
  _raw_spin_lock+0x38/0x50
  iscsi_check_transport_timeouts+0x3e/0x210 [libiscsi]
  call_timer_fn+0x132/0x470
  __run_timers.part.0+0x39f/0x5b0
  run_timer_softirq+0x63/0xc0
  __do_softirq+0x12d/0x5fd
  irq_exit+0xb3/0x110
  smp_apic_timer_interrupt+0x131/0x3d0
  apic_timer_interrupt+0xf/0x20
  default_idle+0x31/0x230
  arch_cpu_idle+0x13/0x20
  default_idle_call+0x53/0x60
  do_idle+0x38a/0x3f0
  cpu_startup_entry+0x24/0x30
  start_secondary+0x222/0x290
  secondary_startup_64+0xa4/0xb0
irq event stamp: 1383705
hardirqs last  enabled at (1383705): [<ffffffff81aace5c>] _raw_spin_unlock_irq+0x2c/0x50
hardirqs last disabled at (1383704): [<ffffffff81aacb98>] _raw_spin_lock_irq+0x18/0x50
softirqs last  enabled at (1383690): [<ffffffffa0e2efea>] iscsi_queuecommand+0x76a/0xa20 [libiscsi]
softirqs last disabled at (1383682): [<ffffffffa0e2e998>] iscsi_queuecommand+0x118/0xa20 [libiscsi]

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&session->frwd_lock)->rlock);
  <Interrupt>
    lock(&(&session->frwd_lock)->rlock);

 *** DEADLOCK ***

2 locks held by kworker/7:1H/206:
 #0: ffff8880d57bf928 ((wq_completion)kblockd){+.+.}, at: process_one_work+0x472/0xab0
 #1: ffff88802b9c7de8 ((work_completion)(&q->timeout_work)){+.+.}, at: process_one_work+0x476/0xab0

stack backtrace:
CPU: 7 PID: 206 Comm: kworker/7:1H Not tainted 5.5.1-dbg+ #11
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
 dump_stack+0xa5/0xe6
 print_usage_bug.cold+0x232/0x23b
 mark_lock+0x8dc/0xa70
 __lock_acquire+0xcea/0x2af0
 lock_acquire+0x106/0x240
 _raw_spin_lock+0x38/0x50
 iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
 scsi_times_out+0xf4/0x440 [scsi_mod]
 scsi_timeout+0x1d/0x20 [scsi_mod]
 blk_mq_check_expired+0x365/0x3a0
 bt_iter+0xd6/0xf0
 blk_mq_queue_tag_busy_iter+0x3de/0x650
 blk_mq_timeout_work+0x1af/0x380
 process_one_work+0x56d/0xab0
 worker_thread+0x7a/0x5d0
 kthread+0x1bc/0x210
 ret_from_fork+0x24/0x30

Fixes: 287922eb ("block: defer timeouts to a workqueue")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191209173457.187370-1-bvanassche@acm.orgSigned-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NLee Duncan <lduncan@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 474e559567fa631dea8fb8407ab1b6090c903755 upstream.

We got the following warnings from thin_check during thin-pool setup:

  $ thin_check /dev/vdb
  examining superblock
  examining devices tree
    missing devices: [1, 84]
      too few entries in btree_node: 41, expected at least 42 (block 138, max_entries = 126)
  examining mapping tree

The phenomenon is the number of entries in one node of details_info tree is
less than (max_entries / 3). And it can be easily reproduced by the following
procedures:

  $ new a thin pool
  $ presume the max entries of details_info tree is 126
  $ new 127 thin devices (e.g. 1~127) to make the root node being full
    and then split
  $ remove the first 43 (e.g. 1~43) thin devices to make the children
    reblance repeatedly
  $ stop the thin pool
  $ thin_check

The root cause is that the B-tree removal procedure in __rebalance2()
doesn't guarantee the invariance: the minimal number of entries in
non-root node should be >= (max_entries / 3).

Simply fix the problem by increasing the rebalance threshold to
make sure the number of entries in each child will be greater
than or equal to (max_entries / 3 + 1), so no matter which
child is used for removal, the number will still be valid.

Cc: stable@vger.kernel.org
Signed-off-by: NHou Tao <houtao1@huawei.com>
Acked-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dbaf971c9cdf10843071a60dcafc1aaab3162354 upstream.

Removes the branching for edge-case where no SCSI device handler
exists.  The __map_bio_fast() method was far too limited, by only
selecting a new pathgroup or path IFF there was a path failure, fix this
be eliminating it in favor of __map_bio().  __map_bio()'s extra SCSI
device handler specific MPATHF_PG_INIT_REQUIRED test is not in the fast
path anyway.

This change restores full path selector functionality for bio-based
configurations that don't haave a SCSI device handler.  But it should be
noted that the path selectors do have an impact on performance for
certain networks that are extremely fast (and don't require frequent
switching).

Fixes: 8d47e659 ("dm mpath: remove unnecessary NVMe branching in favor of scsi_dh checks")
Cc: stable@vger.kernel.org
Reported-by: NDrew Hastings <dhastings@crucialwebhost.com>
Suggested-by: NMartin Wilck <mwilck@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 43cb86799ff03e9819c07f37f72f80f8246ad7ed upstream.

With commit 222ec161 ("drm: Add aspect ratio parsing in DRM
layer") the drm core started honoring the picture_aspect_ratio field
when comparing two drm_display_modes. Prior to that it was ignored.
When the CVBS encoder driver was initially submitted there was no aspect
ratio check.

Switch from drm_mode_equal() to drm_mode_match() without
DRM_MODE_MATCH_ASPECT_RATIO to fix "kmscube" and X.org output using the
CVBS connector. When (for example) kmscube sets the output mode when
using the CVBS connector it passes HDMI_PICTURE_ASPECT_NONE, making the
drm_mode_equal() fail as it include the aspect ratio.

Prior to this patch kmscube reported:
  failed to set mode: Invalid argument

The CVBS mode checking in the sun4i (drivers/gpu/drm/sun4i/sun4i_tv.c
sun4i_tv_mode_to_drm_mode) and ZTE (drivers/gpu/drm/zte/zx_tvenc.c
tvenc_mode_{pal,ntsc}) drivers don't set the "picture_aspect_ratio" at
all. The Meson VPU driver does not rely on the aspect ratio for the CVBS
output so we can safely decouple it from the hdmi_picture_aspect
setting.

Cc: <stable@vger.kernel.org>
Fixes: 222ec161 ("drm: Add aspect ratio parsing in DRM layer")
Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
[narmstrong: squashed with drm: meson: venc: cvbs: deduplicate the meson_cvbs_mode lookup code]
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191208171832.1064772-3-martin.blumenstingl@googlemail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6645d42d79d33e8a9fe262660a75d5f4556bbea9 upstream.

In the implementation of sync_file_merge() the allocated sync_file is
leaked if number of fences overflows. Release sync_file by goto err.

Fixes: a02b9dc9 ("dma-buf/sync_file: refactor fence storage in struct sync_file")
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191122220957.30427-1-navid.emamdoost@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d567fb8819162099035e546b11a736e29c2af0ea upstream.

Since irq_bypass_register_producer() is called after request_irq(), we
should do tear-down in reverse order: irq_bypass_unregister_producer()
then free_irq().

Specifically free_irq() may release resources required by the
irqbypass del_producer() callback.  Notably an example provided by
Marc Zyngier on arm64 with GICv4 that he indicates has the potential
to wedge the hardware:

 free_irq(irq)
   __free_irq(irq)
     irq_domain_deactivate_irq(irq)
       its_irq_domain_deactivate()
         [unmap the VLPI from the ITS]

 kvm_arch_irq_bypass_del_producer(cons, prod)
   kvm_vgic_v4_unset_forwarding(kvm, irq, ...)
     its_unmap_vlpi(irq)
       [Unmap the VLPI from the ITS (again), remap the original LPI]
Signed-off-by: NJiang Yi <giangyi@amazon.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 6d7425f1 ("vfio: Register/unregister irq_bypass_producer")
Link: https://lore.kernel.org/kvm/20191127164910.15888-1-giangyi@amazon.comReviewed-by: NMarc Zyngier <maz@kernel.org>
Reviewed-by: NEric Auger <eric.auger@redhat.com>
[aw: commit log]
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d70f7d31a9e2088e8a507194354d41ea10062994 upstream.

There is an unfortunate typo in the code that results in writing to
FLOW_CTLR_HALT instead of FLOW_CTLR_CSR.

Cc: <stable@vger.kernel.org>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NDmitry Osipenko <digetx@gmail.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d60d0cff4ab01255b25375425745c3cff69558ad upstream.

fin_pll is the parent of clock-controller@7e00f000, specify
the dependency to ensure proper initialization order of clock
providers.

without this patch:
[    0.000000] S3C6410 clocks: apll = 0, mpll = 0
[    0.000000]  epll = 0, arm_clk = 0

with this patch:
[    0.000000] S3C6410 clocks: apll = 532000000, mpll = 532000000
[    0.000000]  epll = 24000000, arm_clk = 532000000

Cc: <stable@vger.kernel.org>
Fixes: 3f6d439f ("clk: reverse default clk provider initialization order in of_clk_init()")
Signed-off-by: NLihua Yao <ylhuajnu@outlook.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9150c3adbf24d77cfba37f03639d4a908ca4ac25 upstream.

If Close command is interrupted before sending a request
to the server the client ends up leaking an open file
handle. This wastes server resources and can potentially
block applications that try to remove the file or any
directory containing this file.

Fix this by putting the close command into a worker queue,
so another thread retries it later.

Cc: Stable <stable@vger.kernel.org>
Tested-by: NFrank Sorenson <sorenson@redhat.com>
Reviewed-by: NRonnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: NPavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: NSteve French <stfrench@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 44805b0e62f15e90d233485420e1847133716bdc upstream.

Currently the client translates O_SYNC and O_DIRECT flags
into corresponding SMB create options when openning a file.
The problem is that on reconnect when the file is being
re-opened the client doesn't set those flags and it causes
a server to reject re-open requests because create options
don't match. The latter means that any subsequent system
call against that open file fail until a share is re-mounted.

Fix this by properly setting SMB create options when
re-openning files after reconnects.

Fixes: 1013e760: ("SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NPavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: NSteve French <stfrench@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 14cc639c17ab0b6671526a7459087352507609e4 upstream.

On reconnect, the transport data structure is NULL and its information is not
available.
Signed-off-by: NLong Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: NSteve French <stfrench@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 37941ea17d3f8eb2f5ac2f59346fab9e8439271a upstream.

While it's not friendly to fail user processes that issue more iovs
than we support, at least we should return the correct error code so the
user process gets a chance to retry with smaller number of iovs.
Signed-off-by: NLong Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: NSteve French <stfrench@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d63cdbae60ac6fbb2864bd3d8df7404f12b7407d upstream.

Log these activities to help production support.
Signed-off-by: NLong Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: NSteve French <stfrench@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4357d45f50e58672e1d17648d792f27df01dfccd upstream.

During reconnecting, the transport may have already been destroyed and is in
the process being reconnected. In this case, return -EAGAIN to not fail and
to retry this I/O.
Signed-off-by: NLong Li <longli@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: NSteve French <stfrench@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 278bcb7300f61785dba63840bd2a8cf79f14554c upstream.

By just cancelling the deferred rx worker during GLINK instance teardown
any pending deferred commands are leaked, so free them.

Fixes: b4f8e52b ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Acked-by: NChris Lew <clew@codeaurora.org>
Tested-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c3dadc19b7564c732598b30d637c6f275c3b77b6 upstream.

Attempting to transmit rx_done messages after the GLINK instance is
being torn down will cause use after free and memory leaks. So cancel
the intent_work and free up the pending intents.

With this there are no concurrent accessors of the channel left during
qcom_glink_native_remove() and there is therefor no need to hold the
spinlock during this operation - which would prohibit the use of
cancel_work_sync() in the release function. So remove this.

Fixes: 1d2ea36e ("rpmsg: glink: Add rx done command")
Cc: stable@vger.kernel.org
Acked-by: NChris Lew <clew@codeaurora.org>
Tested-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f7e714988edaffe6ac578318e99501149b067ba0 upstream.

The device release function is set before registering with rpmsg. If
rpmsg registration fails, the framework will call device_put(), which
invokes the release function. The channel create logic does not need to
free rpdev if rpmsg_register_device() fails and release is called.

Fixes: b4f8e52b ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Tested-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NChris Lew <clew@codeaurora.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b646293e272816dd0719529dcebbd659de0722f7 upstream.

In a remote processor crash scenario, there is no guarantee the remote
processor sent close requests before it went into a bad state. Remove
the reference that is normally handled by the close command in the
so channel resources can be released.

Fixes: b4f8e52b ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Tested-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NChris Lew <clew@codeaurora.org>
Reported-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ac74ea01860170699fb3b6ea80c0476774c8e94f upstream.

Extra channel reference put when remote sending OPEN_ACK after timeout
causes use-after-free while handling next remote CLOSE command.

Remove extra reference put in timeout case to avoid use-after-free.

Fixes: b4f8e52b ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Tested-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NArun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b85f6b601407347f5425c4c058d1b7871f5bf4f0 upstream.

Memory allocated for re-usable intents are not freed during channel
cleanup which causes memory leak in system.

Check and free all re-usable memory to avoid memory leak.

Fixes: 933b45da ("rpmsg: glink: Add support for TX intents")
Cc: stable@vger.kernel.org
Acked-By: NChris Lew <clew@codeaurora.org>
Tested-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NArun Kumar Neelakantam <aneela@codeaurora.org>
Reported-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4623e8bf1de0b86e23a56cdb39a72f054e89c3bd upstream.

When wrapping around the FIFO, the remote expects the tail pointer to
be reset to 0 on the edge case where the tail equals the FIFO length.

Fixes: caf989c3 ("rpmsg: glink: Introduce glink smem based transport")
Cc: stable@vger.kernel.org
Signed-off-by: NChris Lew <clew@codeaurora.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 36de10c4788efc6efe6ff9aa10d38cb7eea4c818 upstream.

Virtual and translated addresses retrieved by the xtensa TLB sanity
checker must be consistent, i.e. correspond to the same state of the
checked TLB entry. KASAN shadow memory is mapped dynamically using
auto-refill TLB entries and thus may change TLB state between the
virtual and translated address retrieval, resulting in false TLB
insanity report.
Move read_xtlb_translation close to read_xtlb_virtual to make sure that
read values are consistent.

Cc: stable@vger.kernel.org
Fixes: a99e07ee ("xtensa: check TLB sanity on return to userspace")
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f338bb9f0179cb959977b74e8331b312264d720b upstream.

Enhance the ACS quirk for Cavium Processors. Add the root port vendor IDs
for ThunderX2 and ThunderX3 series of processors.

[bhelgaas: add Fixes: and stable tag]
Fixes: f2ddaf8d ("PCI: Apply Cavium ThunderX ACS quirk to more Root Ports")
Link: https://lore.kernel.org/r/20191111024243.GA11408@dc5-eodlnx05.marvell.comSigned-off-by: NGeorge Cherian <george.cherian@marvell.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NRobert Richter <rrichter@marvell.com>
Cc: stable@vger.kernel.org	# v4.12+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e045fa29e89383c717e308609edd19d2fd29e1be upstream.

When a driver enables MSI-X, msix_program_entries() reads the MSI-X Vector
Control register for each vector and saves it in desc->masked.  Each
register is 32 bits and bit 0 is the actual Mask bit.

When we restored these registers during resume, we previously set the Mask
bit if *any* bit in desc->masked was set instead of when the Mask bit
itself was set:

  pci_restore_state
    pci_restore_msi_state
      __pci_restore_msix_state
        for_each_pci_msi_entry
          msix_mask_irq(entry, entry->masked)   <-- entire u32 word
            __pci_msix_desc_mask_irq(desc, flag)
              mask_bits = desc->masked & ~PCI_MSIX_ENTRY_CTRL_MASKBIT
              if (flag)       <-- testing entire u32, not just bit 0
                mask_bits |= PCI_MSIX_ENTRY_CTRL_MASKBIT
              writel(mask_bits, desc_addr + PCI_MSIX_ENTRY_VECTOR_CTRL)

This means that after resume, MSI-X vectors were masked when they shouldn't
be, which leads to timeouts like this:

  nvme nvme0: I/O 978 QID 3 timeout, completion polled

On resume, set the Mask bit only when the saved Mask bit from suspend was
set.

This should remove the need for 19ea025e1d28 ("nvme: Add quirk for Kingston
NVME SSD running FW E8FK11.T").

[bhelgaas: commit log, move fix to __pci_msix_desc_mask_irq()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204887
Link: https://lore.kernel.org/r/20191008034238.2503-1-jian-hong@endlessm.com
Fixes: f2440d9a ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: NJian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d8558ac8c93d429d65d7490b512a3a67e559d0d4 upstream.

According to documentation [0] the correct offset for the Upstream Peer
Decode Configuration Register (UPDCR) is 0x1014.  It was previously defined
as 0x1114.

d99321b6 ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
intended to enforce isolation between PCI devices allowing them to be put
into separate IOMMU groups.  Due to the wrong register offset the intended
isolation was not fully enforced.  This is fixed with this patch.

Please note that I did not test this patch because I have no hardware that
implements this register.

[0] https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/4th-gen-core-family-mobile-i-o-datasheet.pdf (page 325)
Fixes: d99321b6 ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
Link: https://lore.kernel.org/r/7a3505df-79ba-8a28-464c-88b83eefffa6@kernkonzept.comSigned-off-by: NSteffen Liebergeld <steffen.liebergeld@kernkonzept.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAndrew Murray <andrew.murray@arm.com>
Acked-by: NAshok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org	# v3.15+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 157c1062fcd86ade3c674503705033051fd3d401 upstream.

A sysfs request to enable or disable a PCIe hotplug slot should not
return before it has been carried out.  That is sought to be achieved by
waiting until the controller's "pending_events" have been cleared.

However the IRQ thread pciehp_ist() clears the "pending_events" before
it acts on them.  If pciehp_sysfs_enable_slot() / _disable_slot() happen
to check the "pending_events" after they have been cleared but while
pciehp_ist() is still running, the functions may return prematurely
with an incorrect return value.

Fix by introducing an "ist_running" flag which must be false before a sysfs
request is allowed to return.

Fixes: 32a8cef2 ("PCI: pciehp: Enable/disable exclusively from IRQ thread")
Link: https://lore.kernel.org/linux-pci/1562226638-54134-1-git-send-email-wangxiongfeng2@huawei.com
Link: https://lore.kernel.org/r/4174210466e27eb7e2243dd1d801d5f75baaffd8.1565345211.git.lukas@wunner.deReported-and-tested-by: NXiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f2c33ccacb2d4bbeae2a255a7ca0cbfd03017b7c upstream.

pci_pm_thaw_noirq() is supposed to return the device to D0 and restore its
configuration registers, but previously it only did that for devices whose
drivers implemented the new power management ops.

Hibernation, e.g., via "echo disk > /sys/power/state", involves freezing
devices, creating a hibernation image, thawing devices, writing the image,
and powering off.  The fact that thawing did not return devices with legacy
power management to D0 caused errors, e.g., in this path:

  pci_pm_thaw_noirq
    if (pci_has_legacy_pm_support(pci_dev)) # true for Mellanox VF driver
      return pci_legacy_resume_early(dev)   # ... legacy PM skips the rest
    pci_set_power_state(pci_dev, PCI_D0)
    pci_restore_state(pci_dev)
  pci_pm_thaw
    if (pci_has_legacy_pm_support(pci_dev))
      pci_legacy_resume
	drv->resume
	  mlx4_resume
	    ...
	      pci_enable_msix_range
	        ...
		  if (dev->current_state != PCI_D0)  # <---
		    return -EINVAL;

which caused these warnings:

  mlx4_core a6d1:00:02.0: INTx is not supported in multi-function mode, aborting
  PM: dpm_run_callback(): pci_pm_thaw+0x0/0xd7 returns -95
  PM: Device a6d1:00:02.0 failed to thaw: error -95

Return devices to D0 and restore config registers for all devices, not just
those whose drivers support new power management.

[bhelgaas: also call pci_restore_state() before pci_legacy_resume_early(),
update comment, add stable tag, commit log]
Link: https://lore.kernel.org/r/KU1P153MB016637CAEAD346F0AA8E3801BFAD0@KU1P153MB0166.APCP153.PROD.OUTLOOK.COMSigned-off-by: NDexuan Cui <decui@microsoft.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org	# v4.13+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a0d4c7eb71dd08a89ad631177bb0cbbabd598f84 upstream.

MMC IOCTLS with R1B responses may cause the card to enter the busy state,
which means it's not ready to receive a new request. To prevent new
requests from being sent to the card, use a CMD13 polling loop to verify
that the card returns to the transfer state, before completing the request.
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: NAvri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3869468e0c4800af52bfe1e0b72b338dcdae2cfc upstream.

To prepare for more users of card_busy_detect(), let's drop the struct
request * as an in-parameter and convert to log the error message via
dev_err() instead of pr_err().
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: NAvri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 64694b27 which is
commit 7faa313f05cad184e8b17750f0cbe5216ac6debb upstream.

Turns out one of the pre-requsite patches wasn't in 4.19.y, so this
patch didn't make sense.  So let's revert it.
Reported-by: NSteven Rostedt <rostedt@goodmis.org>
Reported-by: NWill Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 721c8dafad26ccfa90ff659ee19755e3377b829d ]

Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the
timestamp of the last synflood. Protect them with READ_ONCE() and
WRITE_ONCE() since reads and writes aren't serialised.

Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was
introduced by a0f82f64 ("syncookies: remove last_synq_overflow from
struct tcp_sock"). But unprotected accesses were already there when
timestamp was stored in .last_synq_overflow.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: NGuillaume Nault <gnault@redhat.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit cb44a08f8647fd2e8db5cc9ac27cd8355fa392d8 ]

When no synflood occurs, the synflood timestamp isn't updated.
Therefore it can be so old that time_after32() can consider it to be
in the future.

That's a problem for tcp_synq_no_recent_overflow() as it may report
that a recent overflow occurred while, in fact, it's just that jiffies
has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31.

Spurious detection of recent overflows lead to extra syncookie
verification in cookie_v[46]_check(). At that point, the verification
should fail and the packet dropped. But we should have dropped the
packet earlier as we didn't even send a syncookie.

Let's refine tcp_synq_no_recent_overflow() to report a recent overflow
only if jiffies is within the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This
way, no spurious recent overflow is reported when jiffies wraps and
'last_overflow' becomes in the future from the point of view of
time_after32().

However, if jiffies wraps and enters the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with
'last_overflow' being a stale synflood timestamp), then
tcp_synq_no_recent_overflow() still erroneously reports an
overflow. In such cases, we have to rely on syncookie verification
to drop the packet. We unfortunately have no way to differentiate
between a fresh and a stale syncookie timestamp.

In practice, using last_overflow as lower bound is problematic.
If the synflood timestamp is concurrently updated between the time
we read jiffies and the moment we store the timestamp in
'last_overflow', then 'now' becomes smaller than 'last_overflow' and
tcp_synq_no_recent_overflow() returns true, potentially dropping a
valid syncookie.

Reading jiffies after loading the timestamp could fix the problem,
but that'd require a memory barrier. Let's just accommodate for
potential timestamp growth instead and extend the interval using
'last_overflow - HZ' as lower bound.
Signed-off-by: NGuillaume Nault <gnault@redhat.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 04d26e7b159a396372646a480f4caa166d1b6720 ]

If no synflood happens for a long enough period of time, then the
synflood timestamp isn't refreshed and jiffies can advance so much
that time_after32() can't accurately compare them any more.

Therefore, we can end up in a situation where time_after32(now,
last_overflow + HZ) returns false, just because these two values are
too far apart. In that case, the synflood timestamp isn't updated as
it should be, which can trick tcp_synq_no_recent_overflow() into
rejecting valid syncookies.

For example, let's consider the following scenario on a system
with HZ=1000:

  * The synflood timestamp is 0, either because that's the timestamp
    of the last synflood or, more commonly, because we're working with
    a freshly created socket.

  * We receive a new SYN, which triggers synflood protection. Let's say
    that this happens when jiffies == 2147484649 (that is,
    'synflood timestamp' + HZ + 2^31 + 1).

  * Then tcp_synq_overflow() doesn't update the synflood timestamp,
    because time_after32(2147484649, 1000) returns false.
    With:
      - 2147484649: the value of jiffies, aka. 'now'.
      - 1000: the value of 'last_overflow' + HZ.

  * A bit later, we receive the ACK completing the 3WHS. But
    cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow()
    says that we're not under synflood. That's because
    time_after32(2147484649, 120000) returns false.
    With:
      - 2147484649: the value of jiffies, aka. 'now'.
      - 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID.

    Of course, in reality jiffies would have increased a bit, but this
    condition will last for the next 119 seconds, which is far enough
    to accommodate for jiffie's growth.

Fix this by updating the overflow timestamp whenever jiffies isn't
within the [last_overflow, last_overflow + HZ] range. That shouldn't
have any performance impact since the update still happens at most once
per second.

Now we're guaranteed to have fresh timestamps while under synflood, so
tcp_synq_no_recent_overflow() can safely use it with time_after32() in
such situations.

Stale timestamps can still make tcp_synq_no_recent_overflow() return
the wrong verdict when not under synflood. This will be handled in the
next patch.

For 64 bits architectures, the problem was introduced with the
conversion of ->tw_ts_recent_stamp to 32 bits integer by commit
cca9bab1 ("tcp: use monotonic timestamps for PAWS").
The problem has always been there on 32 bits architectures.

Fixes: cca9bab1 ("tcp: use monotonic timestamps for PAWS")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: NGuillaume Nault <gnault@redhat.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 73e6551699a32fac703ceea09214d6580edcf2d5 ]

When the user changes prio2buffer mapping while global pause is
enabled, mlx5 driver incorrectly sets all active buffers
(buffer that has at least one priority mapped) to lossy.

Solution:
If global pause is enabled, set all the active buffers to lossless
in prio2buffer command.
Also, add error message when buffer size is not enough to meet
xoff threshold.

Fixes: 0696d608 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9cf1cd8ee3ee09ef2859017df2058e2f53c5347f ]

In order to set/get/dump, the tipc uses the generic netlink
infrastructure. So, when tipc module is inserted, init function
calls genl_register_family().
After genl_register_family(), set/get/dump commands are immediately
allowed and these callbacks internally use the net_generic.
net_generic is allocated by register_pernet_device() but this
is called after genl_register_family() in the __init function.
So, these callbacks would use un-initialized net_generic.

Test commands:
    #SHELL1
    while :
    do
        modprobe tipc
        modprobe -rv tipc
    done

    #SHELL2
    while :
    do
        tipc link list
    done

Splat looks like:
[   59.616322][ T2788] kasan: CONFIG_KASAN_INLINE enabled
[   59.617234][ T2788] kasan: GPF could be caused by NULL-ptr deref or user memory access
[   59.618398][ T2788] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[   59.619389][ T2788] CPU: 3 PID: 2788 Comm: tipc Not tainted 5.4.0+ #194
[   59.620231][ T2788] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   59.621428][ T2788] RIP: 0010:tipc_bcast_get_broadcast_mode+0x131/0x310 [tipc]
[   59.622379][ T2788] Code: c7 c6 ef 8b 38 c0 65 ff 0d 84 83 c9 3f e8 d7 a5 f2 e3 48 8d bb 38 11 00 00 48 b8 00 00 00 00
[   59.622550][ T2780] NET: Registered protocol family 30
[   59.624627][ T2788] RSP: 0018:ffff88804b09f578 EFLAGS: 00010202
[   59.624630][ T2788] RAX: dffffc0000000000 RBX: 0000000000000011 RCX: 000000008bc66907
[   59.624631][ T2788] RDX: 0000000000000229 RSI: 000000004b3cf4cc RDI: 0000000000001149
[   59.624633][ T2788] RBP: ffff88804b09f588 R08: 0000000000000003 R09: fffffbfff4fb3df1
[   59.624635][ T2788] R10: fffffbfff50318f8 R11: ffff888066cadc18 R12: ffffffffa6cc2f40
[   59.624637][ T2788] R13: 1ffff11009613eba R14: ffff8880662e9328 R15: ffff8880662e9328
[   59.624639][ T2788] FS:  00007f57d8f7b740(0000) GS:ffff88806cc00000(0000) knlGS:0000000000000000
[   59.624645][ T2788] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   59.625875][ T2780] tipc: Started in single node mode
[   59.626128][ T2788] CR2: 00007f57d887a8c0 CR3: 000000004b140002 CR4: 00000000000606e0
[   59.633991][ T2788] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   59.635195][ T2788] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   59.636478][ T2788] Call Trace:
[   59.637025][ T2788]  tipc_nl_add_bc_link+0x179/0x1470 [tipc]
[   59.638219][ T2788]  ? lock_downgrade+0x6e0/0x6e0
[   59.638923][ T2788]  ? __tipc_nl_add_link+0xf90/0xf90 [tipc]
[   59.639533][ T2788]  ? tipc_nl_node_dump_link+0x318/0xa50 [tipc]
[   59.640160][ T2788]  ? mutex_lock_io_nested+0x1380/0x1380
[   59.640746][ T2788]  tipc_nl_node_dump_link+0x4fd/0xa50 [tipc]
[   59.641356][ T2788]  ? tipc_nl_node_reset_link_stats+0x340/0x340 [tipc]
[   59.642088][ T2788]  ? __skb_ext_del+0x270/0x270
[   59.642594][ T2788]  genl_lock_dumpit+0x85/0xb0
[   59.643050][ T2788]  netlink_dump+0x49c/0xed0
[   59.643529][ T2788]  ? __netlink_sendskb+0xc0/0xc0
[   59.644044][ T2788]  ? __netlink_dump_start+0x190/0x800
[   59.644617][ T2788]  ? __mutex_unlock_slowpath+0xd0/0x670
[   59.645177][ T2788]  __netlink_dump_start+0x5a0/0x800
[   59.645692][ T2788]  genl_rcv_msg+0xa75/0xe90
[   59.646144][ T2788]  ? __lock_acquire+0xdfe/0x3de0
[   59.646692][ T2788]  ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[   59.647340][ T2788]  ? genl_lock_dumpit+0xb0/0xb0
[   59.647821][ T2788]  ? genl_unlock+0x20/0x20
[   59.648290][ T2788]  ? genl_parallel_done+0xe0/0xe0
[   59.648787][ T2788]  ? find_held_lock+0x39/0x1d0
[   59.649276][ T2788]  ? genl_rcv+0x15/0x40
[   59.649722][ T2788]  ? lock_contended+0xcd0/0xcd0
[   59.650296][ T2788]  netlink_rcv_skb+0x121/0x350
[   59.650828][ T2788]  ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[   59.651491][ T2788]  ? netlink_ack+0x940/0x940
[   59.651953][ T2788]  ? lock_acquire+0x164/0x3b0
[   59.652449][ T2788]  genl_rcv+0x24/0x40
[   59.652841][ T2788]  netlink_unicast+0x421/0x600
[ ... ]

Fixes: 7e436905 ("tipc: fix a slab object leak")
Fixes: a62fbcce ("tipc: make subscriber server support net namespace")
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Acked-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9424e2e7ad93ffffa88f882c9bc5023570904b55 ]

Back in 2008, Adam Langley fixed the corner case of packets for flows
having all of the following options : MD5 TS SACK

Since MD5 needs 20 bytes, and TS needs 12 bytes, no sack block
can be cooked from the remaining 8 bytes.

tcp_established_options() correctly sets opts->num_sack_blocks
to zero, but returns 36 instead of 32.

This means TCP cooks packets with 4 extra bytes at the end
of options, containing unitialized bytes.

Fixes: 33ad798c ("tcp: options clean up")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>