When we restart system using sysrq RT3290 device do not initalize
properly, hance always enable it via WLAN_FUN_CTRL register on
probe.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=85461Reported-and-tested-by: NGiedrius Statkevičius <edrius.statkevicius@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Support for the RT5350 WiSoC was added to OpenWrt after having a
lengthy debate about the legality of the original submission, see
https://lists.openwrt.org/pipermail/openwrt-devel/2013-January/018224.html
MTK/Ralink Acked replied and says we can merge this patch under the GPL.
https://dev.openwrt.org/changeset/36177Signed-off-by: NSerge Vasilugin <vasilugin@yandex.ru>
Tested-by: NMichel Stempin <michel.stempin@wanadoo.fr>
Acked-by: NJohn Crispin <blogic@openwrt.org>
[daniel@makrotopia.org: added commit message, cleaned up code]
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On Rt3352 the driver needs to know the frequency of an external
crystal which can be either 40 MHz (as on all other WiSoCs until now)
or 20 MHz.
Get the clock attached by ramips WiSoC platform code which probes
SYSC_REG_SYSCFG (added by John Crispin in commit 6ac8579b) and
introduce a new flag clk_is_20mhz in struct hw_mode_spec to make the
driver aware and use either 40 MHz or 20 MHz specific rf_vals on those
WiSoC platforms.
The introduced support for boards with a 20 MHz crystal is also needed
for RT5350.
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NMathias Kresin <dev@kresin.me>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is needed for WiFi to work e.g. on DIR-615 rev.H1 which got
external RF power amplifiers connected to the WiSoC.
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Simple patch to correct HT20/HT40 filter setting.
Tested with Rt3290, Rt3352 and Rt5350
Signed-off-by: NSerge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since rt2800pci update beacon settings asynchronously from
tbtt tasklet, without beacon_skb_mutex protection, number of
currently active beacons entries can be different than
number pointed by rt2x00dev->intf_beaconing. Remove warning
about that inconsistency.

Reported-by: evaxige@qq.com
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

All Ralink USB devices I have, including old ones, work well with
max_psdu = 3 (64kB tx AMPDUs).

Fix indent on the way.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Enable RTS frame retry fall-back and limit number of RTS retries to 7
what is default number of retries for small frames. As RTS/CTS is used
for TXOP protection, those settings prevent posting lots of RTS
frames when remote station do not response with CTS at the moment. After
sending 7 RTS's the HW will start back-off mechanism and after it will
start posing RTS again to get access to the medium.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We do not have option to set per frame retry count. We have only global
TX_RTY_CFG registers which specify the number or retries. Set setting
of that register to value that correspond rate control algorithm number
of frame post (number of retries + 1), which is 3 for aggregated frames.
This should help with big amount of retries on bad conditions, hence
mitigate buffer-bloat like problems.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

msleep(1) can sleep much more time then requested 1ms, this is not good
on channel switch, which we want to be performed fast (i.e. to make scan
faster). Replace msleep() with usleep_range(), which has much smaller
maximum sleeping time boundary.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This procedure can sleep, hence mdelay is not needed.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since we reset TX_PIN_CFG register, we have to finish recalibration.
Warn if this is not possible.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We have different modes of adjusting freq offset on different chips.
Call current adjustment similarly like vendor driver - mode1 .
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

MAX_LEN_CFG_MAX_PSDU specify maximum transmitted by HW AMPDU length
(0 - 8kB, 1 - 16kB, 2 - 32kB, 3 - 64kB). Set this option according to
remote stations capabilities (based on HT ampdu_factor). However limit
the value based our hardware TX capabilities as some chips can not send
more than 16kB (factor 1). Limit for all chips is currently 32kB
(factor 2), but perhaps for some chips this could be increased
to 64kB by setting drv_data->max_psdu to 3.

Since MAX_LEN_CFG_MAX_PSDU is global setting, on multi stations modes
(AP, IBSS, mesh) we limit according to less capable remote STA. We can
not set bigger value to speed up communication with some stations and
do not break communication with slow stations.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Initalize max ampdu_factor supported by us based on rx chains, vendor
driver do the same.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Sending frames in CCK rates on HT can cause performance problems.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use RTS/CTS protection for TXOP on all rates modes as default and
disable CCK rates (this cause performance problems).
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Change default to RTS/CTS protection. This has a cost of transmitting
one more control frame (RTS) however protect us from traffic from
hidden node.

On station mode will use CTS-to-self if AP will configure that
for the network.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Those TX_SW_CFG1 values are used in vendor driver.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Initialize AUTO_RSP_CFG register to similar value as vendor driver does.

Do not set BAC_ACK_POLICY based on short preamble setting, those are
unrelated.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We already initlized WPDMA_GLO_CFG_WP_DMA_BURST_SIZE to 3 on
rt2800_init_registers() for USB devices. For PCI devices we will use
HW default setting, which is 2, so patch does not change behaviour
on PCI devices.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We should only set IEEE80211_HT_MCS_TX_RX_DIF when TX and RX MCS sets
are not equal, i.e. when number of tx streams is different than
number of RX streams.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On some devices the EEPROMs of Ralink Wi-Fi chips have a default Ralink
MAC address set (RT3062F: 00:0C:43:30:62:00, RT3060F:
00:0C:43:30:60:00). Using multiple of these devices in the same network
can cause nasty issues.

Allow to override the MAC in the EEPROM with (a known good) one set in
the device tree to bypass the issue.
Signed-off-by: NMathias Kresin <dev@kresin.me>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If rt2800usb is loaded with nohwcrypt=1, mac80211 takes
care of the crypto with software encryption/decryption
and thus, MFP can be used.

Tested for secured mesh using ath9k_htc and ath9k.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since commit df140465 ("mac80211: remove support for IFF_PROMISC")
monitor mode for rt2x00 has been made effectively useless because the
hardware filter is configured to drop packets whose intended recipient is
not the device, regardless of the presence of monitor mode interfaces.

This patch fixes this regression by adding explicit monitor mode support,
and by configuring the hardware filter accordingly.
Signed-off-by: NEli Cooper <elicooper@gmx.com>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

On some hardware reading WCID entries table results getting 0xff
numbers, no matter of value written there before. This cause assigning
the same WCID for different stations and makes not possible to connect
to more than one station.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.

This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.

The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.

Removing it removes a lot of corner cases.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

All of the survey data is (currently) per channel anyway,
so having the word "channel" in the name does nothing. In
the next patch I'll introduce global data to the survey,
where the word "channel" is actually confusing.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently implemented temperature compensation is only valid on some of
supported chips. Other chips do not need temperature compensation or
need different way to do this (not yet implemented in the rt2800
driver). Trying to do run rt2800_get_gain_calibration_delta() when this
is not appropriate on particular chip gives bogus result of TX power
and can make connection unstable.

This is follow up to commit 8c8d2017
"rt2800: fix RT5390 & RT3290 TX power settings regression". On that
commit we avoid setting BBP_R1 register, but the real problem is wrong
temperature compensation calculation.
Reported-and-tested-by: NRonald Wahl <ronald.wahl@raritan.com>
Debugged-by: NRonald Wahl <ronald.wahl@raritan.com>
Cc: Mike Romberg <mike-romberg@comcast.net>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NCanek Peláez Valdés <canek@ciencias.unam.mx>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>