The PCI core provides a pci_flags definition (currently __weak), so drop
the arm definition in favor of that.

We EXPORT_SYMBOL(pci_flags) as arm did previously.  I'm dubious about
this: no other architecture exports it, and I didn't see any modules in
the tree that reference it.

CC: Rob Herring <rob.herring@calxeda.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Some architectures (alpha, mips, powerpc) have an arch-specific
"pci_probe_only" flag.  Others use PCI_PROBE_ONLY in pci_flags for
the same purpose.  This moves alpha to the pci_flags approach so
generic code can use the same test across all architectures.

CC: linux-alpha@vger.kernel.org
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Add a pci_clear_flags() for cases when we statically initialize
pci_flags, then decide to clear things out later.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

If we move resource assignment functions into the core, we'll still
need a way for architectures to prevent reassignment, e.g., the
"pci_probe_only" functionality, and we'll need a generic, always
available way the core can test for that.  The "pci_flags"
arrangement used by several architectures seems like a convenient
way to do this.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The PCI fixups get executed based upon whether they are linked in. We need
to avoid executing them if we boot a dual SoC/PC type kernel on a PC class
system.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

ATOMISP on Medfield is a real PCI device which should be handled differently
than the fake PCI devices on south complex. PCI type 1 access is used for
accessing config space this also has other impact such as PM D3 delay. There
shouldn't be any need for reading base address from IUNIT via msg bus.
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Langwell devices are not true pci devices, they are not subject to the 10 ms
d3 to d0 delay required by pci spec. This patch assigns d3_delay to 0 for all
langwell pci devices.

We can also power off devices that are not really used by the OS
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add a parameter to avoid using MSI/MSI-X for PCIe native hotplug; it's
known to be buggy on some platforms.

In my environment, while shutting down, following stack trace is shown
sometimes.

  irq 16: nobody cared (try booting with the "irqpoll" option)
  Pid: 1081, comm: reboot Not tainted 3.2.0 #1
  Call Trace:
   <IRQ>  [<ffffffff810cec1d>] __report_bad_irq+0x3d/0xe0
   [<ffffffff810cee1c>] note_interrupt+0x15c/0x210
   [<ffffffff810cc485>] handle_irq_event_percpu+0xb5/0x210
   [<ffffffff810cc621>] handle_irq_event+0x41/0x70
   [<ffffffff810cf675>] handle_fasteoi_irq+0x55/0xc0
   [<ffffffff81015356>] handle_irq+0x46/0xb0
   [<ffffffff814fbe9d>] do_IRQ+0x5d/0xe0
   [<ffffffff814f146e>] common_interrupt+0x6e/0x6e
   [<ffffffff8106b040>] ? __do_softirq+0x60/0x210
   [<ffffffff8108aeb1>] ? hrtimer_interrupt+0x151/0x240
   [<ffffffff814fb5ec>] call_softirq+0x1c/0x30
   [<ffffffff810152d5>] do_softirq+0x65/0xa0
   [<ffffffff8106ae9d>] irq_exit+0xbd/0xe0
   [<ffffffff814fbf8e>] smp_apic_timer_interrupt+0x6e/0x99
   [<ffffffff814f9e5e>] apic_timer_interrupt+0x6e/0x80
   <EOI>  [<ffffffff814f0fb1>] ? _raw_spin_unlock_irqrestore+0x11/0x20
   [<ffffffff812629fc>] pci_bus_write_config_word+0x6c/0x80
   [<ffffffff81266fc2>] pci_intx+0x52/0xa0
   [<ffffffff8127de3d>] pci_intx_for_msi+0x1d/0x30
  [<ffffffff8127e4fb>] pci_msi_shutdown+0x7b/0x110
   [<ffffffff81269d34>] pci_device_shutdown+0x34/0x50
   [<ffffffff81326c4f>] device_shutdown+0x2f/0x140
   [<ffffffff8107b981>] kernel_restart_prepare+0x31/0x40
   [<ffffffff8107b9e6>] kernel_restart+0x16/0x60
   [<ffffffff8107bbfd>] sys_reboot+0x1ad/0x220
   [<ffffffff814f4b90>] ? do_page_fault+0x1e0/0x460
   [<ffffffff811942d0>] ? __sync_filesystem+0x90/0x90
   [<ffffffff8105c9aa>] ? __cond_resched+0x2a/0x40
   [<ffffffff814ef090>] ? _cond_resched+0x30/0x40
   [<ffffffff81169e17>] ? iterate_supers+0xb7/0xd0
   [<ffffffff814f9382>] system_call_fastpath+0x16/0x1b
  handlers:
  [<ffffffff8138a0f0>] usb_hcd_irq
  [<ffffffff8138a0f0>] usb_hcd_irq
  [<ffffffff8138a0f0>] usb_hcd_irq
  Disabling IRQ #16

An un-wanted interrupt is generated when PCI driver switches from
MSI/MSI-X to INTx while shutting down the device.  The interrupt does
not happen if MSI/MSI-X is not used on the device.
I confirmed that this problem does not happen if pcie_hp=nomsi was
specified and hotplug operation worked fine as usual.

v2: Automatically disable MSI/MSI-X against following device:
    PCI bridge: Integrated Device Technology, Inc. Device 807f (rev 02)
v3: Based on the review comment, combile the if statements.
v4: Removed module parameter.
    Move some code to build pciehp as a module.
    Move device specific code to driver/pci/quirks.c.
v5: Drop a device specific code until getting a vendor statement.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NMUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Only one user in driver/pci/pci.c, so we don't need to put it in global
pci.h
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

unreferenced object 0xffff880276d17700 (size 64):
  comm "swapper/0", pid 1, jiffies 4294897182 (age 3976.028s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 18 f9 de 76 02 88 ff ff  ...........v....
    10 00 00 00 0e 00 00 00 0f 28 40 00 00 00 00 00  .........(@.....
  backtrace:
    [<ffffffff81c8aede>] kmemleak_alloc+0x26/0x43
    [<ffffffff811385f0>] __kmalloc+0x121/0x183
    [<ffffffff813cf821>] pci_add_cap_save_buffer+0x35/0x7c
    [<ffffffff813d12b7>] pci_allocate_cap_save_buffers+0x1d/0x65
    [<ffffffff813cdb52>] pci_device_add+0x92/0xf1
    [<ffffffff81c8afe6>] pci_scan_single_device+0x9f/0xa1
    [<ffffffff813cdbd2>] pci_scan_slot.part.20+0x21/0x106
    [<ffffffff813cdce2>] pci_scan_slot+0x2b/0x35
    [<ffffffff81c8dae4>] __pci_scan_child_bus+0x51/0x107
    [<ffffffff81c8d75b>] pci_scan_bridge+0x376/0x6ae
    [<ffffffff81c8db60>] __pci_scan_child_bus+0xcd/0x107
    [<ffffffff81c8dbab>] pci_scan_child_bus+0x11/0x2a
    [<ffffffff81cca58c>] pci_acpi_scan_root+0x18b/0x21c
    [<ffffffff81c916be>] acpi_pci_root_add+0x1e1/0x42a
    [<ffffffff81406210>] acpi_device_probe+0x50/0x190
    [<ffffffff814a0227>] really_probe+0x99/0x126

Need to free saved_buffer for capabilities.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Found debug print of class is shifted.

| pci 0000:f8:15.2: [8086:2b56] type 0 class 0x000600

Code is trying to print class with 6 digits, but use shifted class with
4 digits valid value as variable.

Change to original dev->class directly.

Also remove not needed calculating of local variable class, because it
will be updated after pci_fixup_device(pci_fixup_early...)

Also unify type print out when class and header is not matched.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Signed-off-by: NAnthony PERARD <anthony.perard@citrix.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Otherwise when rescan is used for cardbus, assigned resources will get
cleared.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Tested-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We should not set the requested size to -2; that will confuse the
resource list sorting with align when SIZEALIGN is used.

Change to STARTALIGN and pass align from start;  we are safe to do that
just as we do that regular pci bridge.  In the long run, we should just
treat cardbus like a regular pci bridge.

Also fix the case when realloc_head is not passed: we should keep the
requested size.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Tested-by: NDominik Brodowski <linux@dominikbrodowski.net>
Acked-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some BIOSes enable prefetch on both MEM0 and MEM1.  But the cardbus code
assumes MEM1 is non-pref...

Discussion could be found at:
	https://lkml.org/lkml/2012/1/12/1
	https://bugzilla.kernel.org/show_bug.cgi?id=41622#c23Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Tested-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If a PCI device is enabled to generate wakeup signals (PME) when put
into a low-power state by runtime PM, it will be still enabled to
generate those signals after the system shutdown, unless its driver's
.shutdown() callback takes care of the wakeup signals generation
setting.  Moreover, there are devices that are not enabled to wake
up the system and that are configured by runtime PM to generate
wakeup signals so that (runtime) remote wakeup works with them.
Those devices should be reconfigured during system shutdown so that
they don't generate wakeup signals, but at least some drivers don't
do that.  However, that very well may be done by the PCI core so
that drivers don't have to worry about it.  For this reason, modify
pci_device_shutdown() to disable the generation of wakeup events for
devices not supposed to wake up the system.

References: https://bugzilla.kernel.org/show_bug.cgi?id=37952Reported-and-tested-by: NKamil Iskra <kamil.54002@iskra.name>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

sysfs is a bit stricter now and emits warnings in more cases.

For SRIOV hotplug, we are calling pci_stop_dev() for each VF first
(after we update pci_stop_bus_devices) which remove each VF subdir.  So
double check the VF dir in /sys before trying to remove the physfn link.
Signed-of-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Distributions may wish to provide different defaults for PCIE ASPM
depending on their target audience. Provide a configuration option for
choosing the default policy.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some BIOS implementations leave the Intel GPU interrupts enabled,
even though no one is handling them (f.e. i915 driver is never loaded).
Additionally the interrupt destination is not set up properly
and the interrupt ends up -somewhere-.

These spurious interrupts are "sticky" and the kernel disables
the (shared) interrupt line after 100.000+ generated interrupts.

Fix it by disabling the still enabled interrupts.
This resolves crashes often seen on monitor unplug.

Tested on the following boards:
- Intel DH61CR: Affected
- Intel DH67BL: Affected
- Intel S1200KP server board: Affected
- Asus P8H61-M LE: Affected, but system does not crash.
  Probably the IRQ ends up somewhere unnoticed.

According to reports on the net, the Intel DH61WW board is also affected.

Many thanks to Jesse Barnes from Intel for helping
with the register configuration and to Intel in general
for providing public hardware documentation.
Signed-off-by: NThomas Jarosch <thomas.jarosch@intra2net.com>
Tested-by: NCharlie Suffin <charlie.suffin@stratus.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

While diagnosing some boot time issues on a platform, all that I
could see in the bootgraph/dmesg was that the system was spending
a lot of time in applying one or more PCI quirks... which
was virtually undebuggable.

This patch adds printk's in "initcall_debug" style to the dmesg,
which are added when the user asks for the initcall_debug
(the nr one tool to use when debugging boot hangs or boot time issues)
kernel command line option.

v2: add #includes so quirks can build on non-x86
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix debug variable from module parameter to be really bool to
fix 'warning: return from incompatible pointer type'.
Acked-by: NScott Murray <scott@spiteful.org>
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

On some OEM systems, pci_restore_state() is called while FLR has not yet
completed.  As a result, PCI BAR register restore is not successful.  This fix
reads back the restored value and compares it with saved value and re-tries 10
times before giving up.
Signed-off-by: NJean Guyader <jean.guyader@eu.citrix.com>
Signed-off-by: NEric Chanudet <eric.chanudet@citrix.com>
Signed-off-by: NAllen Kay <allen.m.kay@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

On a system with a repeater on the system board to support gen2 hotplug,
we found that when an ExpressModule is removed from some slots,
/var/log/messages will be full of "card present/not present" warnings.

It turns out the root complex is continually trying to train the link to
the repeater because the repeater has not been reset.

This patch will disable the link at removal time to allow the repeater
to be reset properly.  This also prevents a potential AER message at
removal time.

Also, when testing hotplug on a system under development, we found if we
boot the system without an EM installed, and later hot-add an EM, it
does not work with Linux, but another OS is ok.  The root cause is that
BIOS left link disabled when slot was empty at boot time, and other OS
is modifying the link disable bit in link ctrl during power on/off.

So we should do the same thing to disable/enable link during power off/on.

-v2: check link DLLA bit instead of 100ms waiting.
     Separate link disable/enable functions to another patch.
Signed-off-by: NYinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Will use it during power off/on of slots
Signed-off-by: NYinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Will use it for link disable status checking.
Signed-off-by: NYinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

A few changes:
  - remove the 'inline' and let the complier decide
  - return a bool to indicate whether the link was active
  - add a debug message to indicate link state when it beocmes active
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

During reviewing
|	PCI: pciehp: wait 1000 ms before Link Training check
Linus said:
>...
> That's a *long* time, and it's irritating to the user. It makes the
> user think "the machine is slow".
>...
> And quite frankly, an unconditional one-second delay here seems bad.
>Two seconds was unacceptable, one second is just bad.

Try to access the pci conf of a pci device that is supposed to show up
in 1s.  If we can read back a valid vendor/device id, we can return
early.

Related discussion could be found:
	https://lkml.org/lkml/2011/12/6/339

-v2: seperate code to pci_bus_read_dev_vendor_id() from pci_scan_device()
    and reuse it from pciehp code. Suggested by Matthew Wilcox.
-v3: According to Kenj, don't use array in stack, and don't wait too long
    for crs, also return fail status if not found.
    Also separate pci_bus_dev_read_vendor_id() change to another patch.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We can reuse it for pciehp probing.

-v2: according to Kenji, fix crs timeout checking, and export the function
     for later use when pciehp is compiled as a module.
Suggested-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When hot removing a pci express module that has a pcie switch and supports
SRIOV, we got:

[ 5918.610127] pciehp 0000:80:02.2:pcie04: pcie_isr: intr_loc 1
[ 5918.615779] pciehp 0000:80:02.2:pcie04: Attention button interrupt received
[ 5918.622730] pciehp 0000:80:02.2:pcie04: Button pressed on Slot(3)
[ 5918.629002] pciehp 0000:80:02.2:pcie04: pciehp_get_power_status: SLOTCTRL a8 value read 1f9
[ 5918.637416] pciehp 0000:80:02.2:pcie04: PCI slot #3 - powering off due to button press.
[ 5918.647125] pciehp 0000:80:02.2:pcie04: pcie_isr: intr_loc 10
[ 5918.653039] pciehp 0000:80:02.2:pcie04: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
[ 5918.661229] pciehp 0000:80:02.2:pcie04: pciehp_set_attention_status: SLOTCTRL a8 write cmd c0
[ 5924.667627] pciehp 0000:80:02.2:pcie04: Disabling domain:bus:device=0000:b0:00
[ 5924.674909] pciehp 0000:80:02.2:pcie04: pciehp_get_power_status: SLOTCTRL a8 value read 2f9
[ 5924.683262] pciehp 0000:80:02.2:pcie04: pciehp_unconfigure_device: domain:bus:dev = 0000:b0:00
[ 5924.693976] libfcoe_device_notification: NETDEV_UNREGISTER eth6
[ 5924.764979] libfcoe_device_notification: NETDEV_UNREGISTER eth14
[ 5924.873539] libfcoe_device_notification: NETDEV_UNREGISTER eth15
[ 5924.995209] libfcoe_device_notification: NETDEV_UNREGISTER eth16
[ 5926.114407] sxge 0000:b2:00.0: PCI INT A disabled
[ 5926.119342] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 5926.127189] IP: [<ffffffff81353a3b>] pci_stop_bus_device+0x33/0x83
[ 5926.133377] PGD 0
[ 5926.135402] Oops: 0000 [#1] SMP
[ 5926.138659] CPU 2
[ 5926.140499] Modules linked in:
...
[ 5926.143754]
[ 5926.275823] Call Trace:
[ 5926.278267]  [<ffffffff81353a38>] pci_stop_bus_device+0x30/0x83
[ 5926.284180]  [<ffffffff81353af4>] pci_remove_bus_device+0x1a/0xba
[ 5926.290264]  [<ffffffff81366311>] pciehp_unconfigure_device+0x110/0x17b
[ 5926.296866]  [<ffffffff81365dd9>] ? pciehp_disable_slot+0x188/0x188
[ 5926.303123]  [<ffffffff81365d6f>] pciehp_disable_slot+0x11e/0x188
[ 5926.309206]  [<ffffffff81365e68>] pciehp_power_thread+0x8f/0xe0
...

 +-[0000:80]-+-00.0-[81-8f]--
 |           +-01.0-[90-9f]--
 |           +-02.0-[a0-af]--
 |           +-02.2-[b0-bf]----00.0-[b1-b3]--+-02.0-[b2]--+-00.0 Device
 |           |                               |            +-00.1 Device
 |           |                               |            +-00.2 Device
 |           |                               |            \-00.3 Device
 |           |                               \-03.0-[b3]--+-00.0 Device
 |           |                                            +-00.1 Device
 |           |                                            +-00.2 Device
 |           |                                            \-00.3 Device

root complex: 80:02.2
pci express modules: have pcie switch and are listed as b0:00.0, b1:02.0 and b1:03.0.
end devices  are b2:00.0 and b3.00.0.
VFs are: b2:00.1,... b2:00.3, and b3:00.1,...,b3:00.3

Root cause: when doing pci_stop_bus_device() with phys fn, it will stop
virt fn and remove the fn, so
	list_for_each_safe(l, n, &bus->devices)
will have problem to refer freed n that is pointed to vf entry.

Solution is just replacing list_for_each_safe() with
list_for_each_prev_safe().  This will make sure we can get valid n pointer
to PF instead of the freed VF pointer (because newly added devices are
inserted to the bus->devices list tail).

During reviewing the patch, Bjorn said:
|   The PCI hot-remove path calls pci_stop_bus_devices() via
|   pci_remove_bus_device().
|
|   pci_stop_bus_devices() traverses the bus->devices list (point A below),
|   stopping each device in turn, which calls the driver remove() method.  When
|   the device is an SR-IOV PF, the driver calls pci_disable_sriov(), which
|   also uses pci_remove_bus_device() to remove the VF devices from the
|   bus->devices list (point B).
|
|       pci_remove_bus_device
|         pci_stop_bus_device
|           pci_stop_bus_devices(subordinate)
|             list_for_each(bus->devices)             <-- A
|               pci_stop_bus_device(PF)
|                 ...
|                   driver->remove
|                     pci_disable_sriov
|                       ...
|                         pci_remove_bus_device(VF)
|                             <remove from bus_list>  <-- B
|
|   At B, we're changing the same list we're iterating through at A, so when
|   the driver remove() method returns, the pci_stop_bus_devices() iterator has
|   a pointer to a list entry that has already been freed.

Discussion thread can be found : https://lkml.org/lkml/2011/10/15/141
				 https://lkml.org/lkml/2012/1/23/360

-v5: According to Linus to make remove more robust, Change to
     list_for_each_prev_safe instead. That is more reasonable, because
     those devices are added to tail of the list before.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Only one user; just use add_to_list instead.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

For use in debugging resource reallocation.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

After merging struct pci_dev_resource_x and pci_dev_resource,
We can use a function instead of macro now.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Linus says don't use dev_res_x because it doesn't communicate anything
about usage.  Rename them to add_res or fail_res etc according to
context.
Suggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pci_dev_resource_x is a superset of pci_dev_resource and they're just
temp structs used during resource reallocation.

pci_dev_resource usage is quite limted.

So just use pci_dev_resource_x, and rename it as new pci_dev_resource.

-v2: According to Linus, Separate free_list change to another patch
Suggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

So we can use helper functions for generic list.  This makes the
resource re-allocation code much more readable.

-v2: Use list_add_tail instead of adding list_insert_before, Pointed out
     by Linus.
Suggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

No user outside of setup-bus.c now.  Later patches will convert
resource_list to a regular list.
Suggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This allows us to move the definition of struct resource_list to
setup_bus.c and later convert resource_list to a regular list.
Suggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

On a system with devices that support SRIOV connected to a pcie switch
to pcie root port:

 +-[0000:80]-+-00.0-[81-8f]--
 |           +-01.0-[90-9f]--
 |           +-02.0-[a0-af]----00.0-[a1-a3]--+-02.0-[a2]--+-00.0 Oracle Corporation Device 207a
 |           |                               \-03.0-[a3]--+-00.0 Oracle Corporation Device 207a
 |           +-02.2-[b0-bf]----00.0-[b1-b3]--+-02.0-[b2]--+-00.0 Oracle Corporation Device 207a
 |           |                               \-03.0-[b3]--+-00.0 Oracle Corporation Device 207a

When the BIOS does not assign resources for SRIOV BARs, kernel pci
reallocation only goes up one bridge and then gives up, failing to to
get resources for all sSRIOV BARs, even though the range is large enough
in the peer root bus.

Specifically, only the bridge at the a1:02.0 level has its resources
cleared and reallocated.  The kernel does not go up to clear the bridge
at the 80:02.0 level.

To make it go to upper levels, during retry, we need to treat "good to have"
resources as "must have".

Only on the last try will we treat good to have resources as optional.
At that time, parent bridge resources will already have been released so
we'll have a chance to get everything assigned with must_have plus
good_to_have for all child devices.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This allows us to allocate resources to hotplug bridges during
remove/rescan.

We need to move the function to setup-bus.c so it can use
__pci_bus_size_bridges and __pci_bus_assign_resources directly to take
the add_list resource tracking list.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Current rescan will not touch bridge MMIO and IO.

Try to reuse pci_assign_unassigned_bridge_resources(bridge) to update bridge
resources, if child devices need more resources.

Only do that for bridges whose children are all removed already; i.e. don't
release resources that could already be in use by drivers on child devices.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>