Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81621Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NAndrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

There are two modprobe parameters for VBI that aren't used
anywhere (one for debug, the other one related to the buffer
size). Get rid of them!
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Signed-off-by: NMorgan Phillips <winter2718@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Signed-off-by: NMorgan Phillips <winter2718@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The norm_swidth function was unused and is dropped. It's not clear
what the purpose of that function was.

The norm_maxh function was changed so it tests for 60 Hz standards
rather than for 50 Hz standards. The is the preferred order.

The norm_maxw function was poorly written and used: it gives the maximum
allowed line width for the given standard. For 60 Hz that's 720, but
for 50 Hz that's 768 which allows for 768x576 which gives you square
pixels. For 60 Hz formats it is 640x480 that gives square pixels, so
there is no need to go beyond 720.

The initial width was set using norm_maxh(), which was wrong. Just set
to 720, that's what you normally use. Since the initial standard was
NTSC anyway the initial width was always 720 anyway.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Tested VBI support and discovered that the wrong offset was used.
After this change it is now working. Verified with CC/XDS for NTSC
and WSS/Teletext on PAL.

It also reported the wrong start lines for the second field. That's
now fixed as well.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Both adv7604 and adv7842 had the same typo in the code that sets
the vertical backporch for the second interlaced field: it was
assigned to vbackporch instead of il_vbackporch.

In addition, the timings struct wasn't zeroed in the adv7842 driver,
leaving several fields to undefined values causing the timing match
function to fail.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

If one or both of the timings being compared have the standards field
with value 0, then accept that. Only check for matching standards if
both timings have actually filled in that field.

Otherwise no match will ever be found since when timings are detected
the standards field will typically be set to 0 by the driver.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is useful to test teletext capture applications like alevt and mtt.

It also fixes a previously undetected bug where the PAL VBI start line
of the second field was off by one. Using the new field start defines
helps a lot fixing such bugs.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

G_EDID is an RW ioctl, so the struct v4l2_edid isn't const.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

A test in uvc_video_decode_isoc() checks whether an image has been
received from the camera completely. For this the data amount is compared
to the buffer length, which, however, doesn't have to be equal to the
image size. Switch to using formats .sizeimage field for an exact
expected image size.

[Renamed image_size to frame_size]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

drivers/media/usb/hackrf/hackrf.c:64:3: warning: this decimal constant is unsigned only in ISO C90 [enabled by default]
   .rangehigh  = 4294967294, /* max u32, hw goes over 7GHz */
   ^
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

HackRF SDR driver. Video4Linux USB device.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

V4L2 driver for HackRF SDR. Very basic version, with reduced
feature set. Driver implements receiver only, hardware supports
also transmitter.

USB ID 1d50:6089. Model HackRF One
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The ARGB32 pixel format's fourcc value is defined to 'BA24' in the
videodev2.h header, but documented as 'AX24'. Fix the documentation.
Reported-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The existing RGB555X pixel format is ill-defined in respect to its alpha
bit and its meaning is driver dependent. Create new standard ARGB555X
and XRGB555X variants with clearly defined meanings and make the
existing variant deprecated.

The new pixel formats 4CC values have been selected to match the DRM
4CCs for the same in-memory formats.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Replace strncpy + manually setting the terminating '\0' with an strlcpy
call.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

As reported on [1], this device needs this quirk to be able to
reliably initialise the webcam.

[1] http://ubuntuforums.org/showthread.php?t=2145996

Cc: stable@vger.kernel.org
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The uvcvideo webcam driver exposes the v4l2 control "Exposure (Absolute)"
which allows the user to control the exposure time of the webcam,
essentially controlling the brightness of the received image.  By default
the webcam automatically adjusts the exposure time automatically but the
if you set the control "Exposure, Auto"="Manual Mode" the user can fix
the exposure time.

Unfortunately it seems that the Logitech C920 has a firmware bug where
it will forget that it's in manual mode temporarily during initialisation.
This means that the camera doesn't respect the exposure time that the user
requested if they request it before starting to stream video.  They end up
with a video stream which is either too bright or too dark and must reset
the controls after video starts streaming.

This patch introduces the quirk UVC_QUIRK_RESTORE_CTRLS_ON_INIT which
causes the cached controls to be re-uploaded to the camera immediately
after initialising the camera.  This quirk is applied to the C920 to work
around this camera bug.
Signed-off-by: NWilliam Manley <will@williammanley.net>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Map V4L2_CID_TILT_SPEED and V4L2_CID_PAN_SPEED to the standard UVC
CT_PANTILT_RELATIVE_CONTROL terminal control request.

Tested by plugging a Logitech ConferenceCam C3000e USB camera
and controlling pan/tilt from the userspace using the VIDIOC_S_CTRL ioctl.
Verified that it can pan and tilt at the same time in both directions.
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Reviewed-by: NPawel Osciak <posciak@chromium.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The V4L2_CID_PAN_SPEED and V4L2_CID_TILT_SPEED controls allow to move the
camera by setting its rotation speed around its axis.
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Reviewed-by: NPawel Osciak <posciak@chromium.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

this patch removes unneeded dependency of ARCH_OMAP3
on VIDEO_DM6446_CCDC.
Also the top level platform Makefile descended into
davinci/ without any dependency so just drop the
dependency obj-y, as obj-$(CONFIG_ARCH_DAVINCI)
already exists.
Reported-by: NAndreas Ruprecht <rupran@einserver.de>
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

It is possible to call STREAMON without having any buffers queued.
So vb2_is_streaming() can return true without start_streaming()
having been called. Only after at least one buffer has been
queued will start_streaming be called.

The check vb2_is_streaming() is incorrect as this would start
the DMA without having proper DMA pointers set up. this patch
uses vb2_start_streaming_called() instead to check is streaming
was called.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

It is possible to call STREAMON without having any buffers queued.
So vb2_is_streaming() can return true without start_streaming()
having been called. Only after at least one buffer has been
queued will start_streaming be called.

The check vb2_is_streaming() is incorrect as this would start
the DMA without having proper DMA pointers set up. this patch
uses vb2_start_streaming_called() instead to check is streaming
was called.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

this patch adds a helper to get the status if start_streaming()
was called successfully.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

this patch drops setting of vb2 buffer state to VB2_BUF_STATE_ACTIVE,
as any buffer queued to the driver is marked ACTIVE by the vb2 core.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

this patch drops setting of vb2 buffer state to VB2_BUF_STATE_ACTIVE,
as any buffer queued to the driver is marked ACTIVE by the vb2 core.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

All the infrastructure for this is already there, and despite our desires for
the old videobuf code to go away, it is currently still in use in 18 drivers.

Allowing reqbufs(0) makes these drivers behave consistent with modern drivers,
making live easier for userspace, see e.g. :
https://bugzilla.gnome.org/show_bug.cgi?id=735660Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

(Changes since v2: dropped local variable as suggested by Laurent)

Commit f035eb4e (videobuf2: fix lockdep warning)
unfortunately removed the mmap_sem lock that is needed around the call to
__qbuf_userptr. Amazingly nobody noticed this (especially me as the author)
until Jan Kara pointed this out to me.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reported-by: NJan Kara <jack@suse.cz>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Test for definedness of the macro which is actually defined, and which
matches the name of the file.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Three trailing underscores is one too many.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This ensures device->streaming has correct status.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch introduces the use of the function usb_endpoint_is_int_in.

The Coccinelle semantic patch that makes these changes is as follows:

@@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
-  \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_INT\|3\))
+ usb_endpoint_xfer_int(epd)

@@ struct usb_endpoint_descriptor *epd; @@

- (usb_endpoint_xfer_int(epd) && usb_endpoint_dir_in(epd))
+ usb_endpoint_is_int_in(epd)
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Use RegMap API to handle all the boring I2C register access
boilerplate stuff.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

foo_dev seems to be most correct term for the structure holding data
of each device instance. It is most used term in Kernel codebase and also
examples from book Linux Device Drivers, Third Edition, uses it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

There is no need to print module name nor function name as those
are done by kernel logging system when dev_xxx logging is used and
driver is proper I2C driver.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Convert driver from DVB proprietary model to common I2C model.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Used tda18212 tuner is implemented as a I2C driver. Use em28xx
tuner I2C client for tda18212 driver.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Used tda18212 tuner is implemented as I2C driver. Implement I2C
client to anysee and use it for tda18212.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

We need carry pointer to frontend via config struct
(I2C platform_data ptr) when I2C model is used. Add that pointer
first in order to keep build unbreakable during conversion.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>