It's unreasonable to have CONFIG_ACPI for these in drivers, so add some
stub functions.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.

After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.

ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot)  If these resources are all ON,
then the state is D3hot.  If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.

This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

With commit a2ef5c4f
"ACPI: Move module parameter gts and bfs to sleep.c" the wake_sleep_flags
is required when calling acpi_enter_sleep_state, which means
that if there are functions outside the sleep.c code they
can't get the wake_sleep_flags values.

This converts the function in to a exported value and converts
the module config operands to a function.
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NLin Ming <ming.m.lin@intel.com>
[v2: Parameters can be turned on/off dynamically]
[v3: unsigned char -> u8]
[v4: val -> kp->arg]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1335150198-21899-2-git-send-email-konrad.wilk@oracle.comSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

This reverts commit cf450136.

It breaks reboot on at least one Thinkpad T43, as reported by Jörg Otte:
 "On reboot it shuts down as normal.
  The last lines displayed are:

  >Unmounting temporary filesystems.. [OK]
  >Deactivating swap...               [OK]
  >Unmounting local filesystems...    [OK]
  >Will now restart
  >    Restarting system

  Then I hear it accessing the cd-drive, but then it's being stuck."

Jörg bisected the regression to this commit.

That commit fixes another machine (see

  https://bugzilla.kernel.org/show_bug.cgi?id=11533

for details) that has a BIOS bug and doesn't support ACPI reset.
However, at least one of those other reporters no longer even has the
machine in question, and had a different workaround to begin with.
Besides, it clearly was a buggy BIOS.  Let's not break the correct case
to fix that case.
Reported-and-bisected-by: NJörg Otte <jrg.otte@googlemail.com>
Cc: linux-acpi@vger.kernel.org
Cc: Len Brown <lenb@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit 6fe0d062.

Paul bisected this regression.

The conversion was done blindly and is wrong, as it does not provide a
primary handler to disable the level type irq on the device level.
Neither does it set the IRQF_ONESHOT flag which handles that at the irq
line level.  This can't be done as the interrupt might be shared, though
we might extend the core to force it.

So an interrupt on this line will wake up the thread, but immediately
unmask the irq after that.  Due to the interrupt being level type the
hardware interrupt is raised over and over and prevents the irq thread
from handling it.  Fail.

request_irq() unfortunately does not refuse such a request and the patch
was obviously never tested with real interrupts.
Bisected-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op.  This leads to a
proliferation of the default_open() implementation across the entire
tree.

Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().

This replacement was done with the following semantic patch:

<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}

@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ACPI code is shared by arch/x86 and arch/ia64. ia64 doesn't provide a plain
"halt()" function.  Use safe_halt() instead.
Signed-off-by: NTony Luck <tony.luck@intel.com>
Tested-by: NBoris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Using a u64 here creates an endian bug.  We store a u32 number in the
top byte which is a larger number than intended on big endian systems.
There is no reason to use a 64 bit data type here, I guess it was just
an oversight.

I removed the initialization to zero as well.  It's needed with a u64
but with a u32, the variable gets initialized properly inside the call
to acpi_os_read_port().
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Quoth Dmitry Torokhov:
In addition to bus notifier we do install device notifier explicitly
so it might fire up early. The easiest fox would be to move
acpi_video_bus_start_devices() after input_allocate_device() but
before input_register_device() - unregistered input devices can handle
input_event() calls just fine.

May fix crashes reported in:
https://bugzilla.kernel.org/show_bug.cgi?id=40672Signed-off-by: NIgor Murzov <e-mail@date.by>
Signed-off-by: NLen Brown <len.brown@intel.com>

It is always better to check return values, so add some new checks and
correct existing ones.

v2: Be consistent and don't mix errors from -E* and AE_* namespaces.
Signed-off-by: NIgor Murzov <e-mail@date.by>
Signed-off-by: NLen Brown <len.brown@intel.com>

ACPI 5.0 adds the BGRT, a table that contains a pointer to the firmware
boot splash and associated metadata. This simple driver exposes it via
/sys/firmware/acpi in order to allow bootsplash applications to draw their
splash around the firmware image and reduce the number of jarring graphical
transitions during boot.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Drivers may wish to add entries to /sys/firmware/acpi, so export acpi_kobj
in order to let them do that.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Make sure the removal of mappings uses the same logic that put the
mappings in place.
Signed-off-by: NMyron Stowe <myron.stowe@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The function apei_estatus_print() and apei_estatus_check() forget to move ahead
the gdata pointer when dealing with multiple generic error data sections.
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Clean the redundant codes of apci_bus_get_power_flags().
Signed-off-by: NAlex He <alex.he@amd.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The acpi_processor_cst_has_changed() function is invoked from a
CPU_ONLINE or CPU_DEAD function, which might well execute on CPU 0
even though the CPU being hotplugged is some other CPU.  In addition,
acpi_processor_cst_has_changed() invokes smp_processor_id() without
protection, resulting in splats when onlining CPUs.

This commit therefore changes the smp_processor_id() to pr->id, as is
used elsewhere in the code, for example, in acpi_processor_add().
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: NYong Zhang <yong.zhang0@gmail.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>

... so that acpi_unmap()'s behavior gets in sync with acpi_map()'s.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The function acpi_processor_add is stored in the ops.add field of a
acpi_driver structure.  This function is then called in
acpi_bus_driver_init.  On failure, this function clears the field
device->driver_data, but does not free its contents.  Thus the free has to
be done by the add function.  In acpi_processor_add, the corresponding
value is pr.  This value is currently freed on failure before storing it in
device->driver_data, but not after.  This free is added in the error
handling code at the end of the function.  The per_cpu variable
processors is also cleared so that it does not refer to a dangling pointer.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: NDeepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The current code incorrectly assumes that
(1) the APEI register bit width is always 8, 16, 32, or 64 and
(2) the APEI register bit width is always equal to the APEI
    register access width.

ERST serialization instructions entries such as:

[030h 0048   1]                       Action : 00 [Begin Write Operation]
[031h 0049   1]                  Instruction : 03 [Write Register Value]
[032h 0050   1]        Flags (decoded below) : 01
                      Preserve Register Bits : 1
[033h 0051   1]                     Reserved : 00

[034h 0052  12]              Register Region : [Generic Address Structure]
[034h 0052   1]                     Space ID : 00 [SystemMemory]
[035h 0053   1]                    Bit Width : 03
[036h 0054   1]                   Bit Offset : 00
[037h 0055   1]         Encoded Access Width : 03 [DWord Access:32]
[038h 0056   8]                      Address : 000000007F2D7038

[040h 0064   8]                        Value : 0000000000000001
[048h 0072   8]                         Mask : 0000000000000007

break this assumption by yielding:
  [Firmware Bug]: APEI: Invalid bit width in GAR [0x7f2d7038/3/0]

I have found no ACPI specification requirements corresponding
with the above assumptions.  There is even a good example in
the Serialization Instruction Entries section (ACPI 4.0 section
17.4,1.2, ACPI 4.0a section 2.5.1.2, ACPI 5.0 section 18.5.1.2)
that mentions a serialization instruction with a bit range of
[6:2] which is 5 bits wide, _not_ 8, 16, 32, or 64 bits wide.

Compile and boot tested with 3.3.0-rc7 on a IBM HX5.
Signed-off-by: NGary Hade <garyhade@us.ibm.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some APEI firmware implementation will access injected address
specified in param1 to trigger the error when injecting memory
error, which means if one SRAR error is injected, the crash
always happens because it is executed in kernel context. This
new parameter can disable trigger action and control is taken
over by the user. In this way, an SRAR error can happen in user
context instead of crashing the system. This function is highly
depended on BIOS implementation so please ensure you know the
BIOS trigger procedure before you enable this switch.

v2:
  notrigger should be created together with param1/param2
Tested-by: NTony Luck <tony.luck@lintel.com>
Signed-off-by: NChen Gong <gong.chen@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

On the platforms with ACPI4.x support, parameter extension
is not always doable, which means only parameter extension
is enabled, einj_param can take effect.

v2->v1: stopping early in einj_get_parameter_address for einj_param
Signed-off-by: NChen Gong <gong.chen@linux.intel.com>
Acked-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This fixes a trivial copy & paste error in ERST header length check.
It's just for future safety because sizeof(struct acpi_table_einj)
equals to sizeof(struct acpi_table_erst) with current ACPI5.0
specification. It applies to v3.3-rc6.
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Acked-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Currently when a CPU is off-lined it enters either MWAIT-based idle or,
if MWAIT is not desired or supported, HLT-based idle (which places the
processor in C1 state). This patch allows processors without MWAIT
support to stay in states deeper than C1.
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

acpi_processor_install_hotplug_notify() registers processor objects to
receive ACPI CPU hotplug event notifications. This patch additionally
registers processor device objects (ACPI0007) to receive the notifications
as well.
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Print physical address info in a style consistent with the %pR style used
elsewhere in the kernel.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

An HP laptop (Pavilion G4-1016tx) has the following code in _TMP:

       Store (\_SB.PCI0.LPCB.EC0.RTMP, Local0)
       If (LGreaterEqual (Local0, S4TP))
       {
           Store (One, HTS4)
       }

S4TP is initialised at 0 and not programmed further until either _HOT or
_CRT is called. If we evaluate _TMP before the trip points then HTS4 will
always be set, causing the firmware to generate a message on boot
complaining that the system shut down because of overheating. The simplest
solution is just to reverse the checking of trip points and _TMP in thermal
init.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

acpi_dev_run_wake() is a generic function which can be used by
other subsystem too. Rename it to acpi_pm_device_run_wake, to be
consistent with acpi_pm_device_sleep_wake.

Then move it to ACPI core.
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Devices may share same list of power resources in _PR0, for example

Device(Dev0)
{
	Name (_PR0, Package (0x01)
	{
		P0PR,
		P1PR
	})
}

Device(Dev1)
{
	Name (_PR0, Package (0x01)
	{
		P0PR,
		P1PR
	}
}

Assume Dev0 and Dev1 were runtime suspended.
Then Dev0 is resumed first and it goes into D0 state.
But Dev1 is left in D0_Uninitialised state.

This is wrong. In this case, Dev1 must be resumed too.

In order to hand this case, each power resource maintains a list of
devices which relies on it.

When power resource is ON, it will check if the devices on its list
can be resumed. The device can only be resumed when all the power
resouces of its _PR0 are ON.
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

If a device has _PR3, it means the device supports D3_COLD.
Add the ability to validate and enter D3_COLD state in ACPI.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Repair a common problem with objects that are defined to return
a variable-length Package of sub-objects. If there is only one
sub-object, some BIOS code mistakenly simply declares the single
object instead of a Package with one sub-object.  This function
attempts to repair this error by wrapping a Package object around
the original object, creating the correct and expected Package
with one sub-object.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some ACPI interrupt actions may need to wait, and it's easiest to
have a thread context for this. So turn the ACPI interrupt
into a threaded interrupt.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

WARN() is not supposed to have side effects, so move the request_regions
outside.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Remove all #inclusions of asm/system.h preparatory to splitting and killing
it.  Performed with the following command:

perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Move linux specific module parameter gts and bfs out of ACPICA core
code to sleep.c.
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Enhanced the sleep/wake interfaces to optionally execute the
_GTS method (Going To Sleep), and the _BFS method (Back From
Sleep).  Windows apparently does not execute these methods, and
therefore these methods are often untested. It has been seen on
some systems where the execution of these methods causes errors
and also prevents the machine from entering S5. It is therefore
suggested that host operating systems do not execute these methods
by default. In the future, perhaps these methods can be optionally
executed based on the age of the system and/or what is the newest
version of Windows that the BIOS asks for via _OSI.
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

On Intel CPUs the processor typically uses the highest frequency
set by any logical CPU. When the system overheats
Linux first forces the frequency to the lowest available one
to lower the temperature.

However this was done only per logical CPU, which means all
logical CPUs in a package would need to go through this before
the frequency is actually lowered.

Worse this delay actually prevents real throttling, because
the real throttle code only proceeds when the lowest frequency
is already reached.

So when a throttle event happens force the lowest frequency
for all CPUs in the package where it happened. The per CPU
state is now kept per package, not per logical CPU. An alternative
would be to do it per cpufreq unit, but since we want to bring
down the temperature of the complete chip it's better
to do it for all.

In principle it may even make sense to do it for all CPUs,
but I kept it on the package for now.

With this change the frequency is actually lowered, which
in terms also allows real throttling to proceed.

I also removed an unnecessary per cpu variable initialization.

v2: Fix package mapping

Cc: <stable@vger.kernel.org>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Many namespace node types must have an attached object. For
these node types, print a message about a missing object during
a namespace dump.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Change the returned exception code from AE_BAD_PARAMETER to the
more appropriate AE_BAD_PATHNAME, when the input pathname to
evaluate object is invalid.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Changed the METHOD_NAME* defines that define a full pathname to
the method to METHOD_PATHNAME* in order to make it clear that
it is not a simple 4-character ACPI name. Used for the various
sleep/wake methods.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Simplifies the code, especially the compile-time
ACPI_REDUCED_HARDWARE option.
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>