The tridentfb driver should handle now all chipsets handled by the cyblafb
driver.  Remove the message which claims that support will be removed.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add imageblit acceleration for the Blade3D family of cores.  The code is
based on code from the cyblafb driver.

It is a step toward assimilating back the cyblafb driver into the
tridentfb driver.  The cyblafb driver handles a subfamily of the Trident
Blade3d cores.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes following problems:
- does not allow the m parameter to reach 0 as
  it locks the graphics core (power cycle needed)
- for the newer chips (with new clock registers)
  does not allow of n / m ratio below 4 as it gives
  unstable image on the Blade3D core
- extend shift parameter (k) range  to 2 for the newer
  chips to cope with the n /m >= 4 limit at low resolution
  (bandwidth) modes
- prefer modes with higher n / m ratio (higher k values)
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Trident cards uses only 20-bit address of screen start in double
words.  This allows addressing for only 4MB of video memory so check this.

Also remove some redundant checks and assignments.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix depth setting for 8 bpp mode.  The nice 224 color logo is not
displayed in 8 bpp depth without this fix.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes two problems when acceleration is enabled:

 - console switch from the Xorg locks up the computer
   because the Xorg code locks some registers and disables
   the mmio mode, so reenable these in the
   tridentfb_set_par() and enable_mmio()

 - blacklist the Image975 chipset from setting PCI burst
   mode. This helps with random lock ups of the
   framebuffer on this chip. The same fix is probably
   needed for the Xorg as well.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch contains general source code improvments:
 - more simple functions are inline
 - removes some meaningless output and the VERSION
   string as it is no use
 - eng_par is moved into the tridentfb_par
 - removed small section of code for CyberBladeXPAi1
   which is maybe right for only one resolution
   and refresh rate and is probably redundant now
 - other minor improvements
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch replaces deprecated constant FB_ACCELF_TEXT with
FBINFO_HWACCEL_DISABLED and adds constants for Trident families of
accelerators.

The FBINFO_HWACCEL_DISABLED is correctly used so noaccel parameter works
now.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes few issues related to timings and pixclock generation:

 - disallow the pixclocks with numerator lower than
   double denominator. This fixes display instability
   for some modes.
 - choose the pixelclock with the highest
   numerator and denominator values. This improve
   image quality and fixes display instability
   for some modes.
 - make interlaced modes work.
 - set synchronization pulses polarization
   correctly.
 - horizontal synchronization timing are now
   the same as generated by X.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes two problems when acceleration is enabled:

 - bit for bitblt direction is corrected
   so scrolling down works as expected on 3DImage chips

 - initialization of acceleration is done later
   this helps with initial console malfuntion (on Blade3D
   chips) well documented here:
   http://marc.info/?l=linux-fbdev-users&m=111386953124478&w=2Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch brings various acceleration improvements:
- set  copyarea/fillrect for non-accelerated framebuffer (fix)
- remove 15 bpp depth handling to simplify code as it hardly
  works (15 bpp handling was obviously missing in some switches)
- add fb_sync call and move waiting before accelerated function
  to make acceleration more asynchronous to cpu (few % of speed
  improvement)
- add cpu_relax() call in waiting loops
- make longer register names and name more registers
- move registers' definition to header
- general code improvements (shortening, simplifying)
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds acceleration for TGUI 9440 and 96xx chips.  These chips
requires line length to be power of 2, so this is also changed.

It also moves the troubling enable_mmio() function to its final
destination.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The TGUI 9440 requires doubling clock for 16bpp (hi-color) modes.

The patch also moves back enable_mmio() call to the right position.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Do not overwrite bits which contain memory type settings.  It removes
noise pixels ("snow") on Blade3D and 3DImage chips.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Do some additional checks (like pixelclock versus ramdac speed) to
eliminate modes which do not work.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Initialize the pseudo_palette pointer properly.  This fixes crash when
16bpp or 32bpp mode is selected.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for TGUI 9440 chip.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improved values for some registers after Xorg Trident driver.  The main
problem was that values set by BIOS have been ignored.

This patch completely remove random pixels ("snow") on the TGUI 9680 and
9440 (not supported yet by the driver).  It does not help with the "snow"
on 3DImage and Blade3D cards.

There is also small improvement in timing calculations (hblank start and
vblank start)
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add missing release of allocated fb_info structure and move enable_mmio() to
fix error path.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Xorg code shows that Trident models 9660, 9680 and 9682 require a
different clock setting method.  Add the second clock setting method for older
models.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the mmio outb function instead of direct one.  The mmio registers are
already mapped (in the probe function).
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix broken timings calculations. This patch helps with following
problems:
 - no left part of screen visible (up to half of the screen)
 - monitor's frequencies are not the ones intended for selected modes
 - if mode with resoultion y > 1024 is selected at least once then
   all modes with y < 1024 are "out of sync" (no display)
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make use of functions and constants from the vga.h header to compact the code
and make it more readable.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch moves acceleration hooks into the tridentfb_par structure and
removes global hooks.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch converts the is_blade() and is_xp() macros into local functions.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch moves flat panel indicator into tridentfb_par structure and removes
related global variables and macros.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch moves the chip_id into tridentfb_par structure and removes global
chip_id related constants.

It also bumps version of the driver to 0.7.9
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch moves pseudo palette int tridentfb_par structure and removes global
default_var.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch converts fb_info structure from global variable to allocatable one.

The global default_par is moved into function variable.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch replaces macros with static functions and puts tridentfb_par
pointer as the first argument of these functions.  These is a step toward
multihead support.

Additionally, bogus TRIDENT_MMIO define is removed as the driver supports
graphics cards only through the mmio mode.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improve clock calculation precision (to kHz from MHz) and removes parameter
field vclk from the tridentfb_par structure.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove redundant enable_mmio() call as the mmio mode is enabled in the probe
function earlier.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add removed option "mode" to keep compatibility with existing setups.  The
option is back for pm2fb, tridentfb and vt8623fb drivers.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change the option "mode_option" into "mode".  It also adds __init attribute to
tridentfb_setup function.

This is one step toward changing all fb drivers to have common "mode_option"
parameter.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Alain Kalker <miki@dds.nl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix memory size multiplier during detection.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove locking registers after they are unlocked during switch to/from MMIO
mode.  This fixes regression on the Blade3D (Trident 9880) caused by the
previous patch (probe fixes).
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Correct error paths in probe function.

The probe function enables mmio mode so it important to disable the mmio
mode before exiting the probe function.  Otherwise, the console is left in
unusable state (garbled fonts at least, lock up at worst).

[akpm@linux-foundation.org: cleanups]
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch contains coding style improvements to the tridentfb driver (white
spaces, indentations, long lines).

It also moves fb_ops structure after fb api functions are defined.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The pseudo_palette has only 16 elements. Do not write if regno (the array
index) is more than 15.
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ioremap must be balanced by an iounmap and failing to do so can result in a
memory leak.
Signed-off-by: NAmol Lad <amol@verismonetworks.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>