- 27 3月, 2008 1 次提交
-
-
由 Alexandr Smirnov 提交于
Add default config for Emerson KSI8560 board. Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 24 3月, 2008 1 次提交
-
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 06 12月, 2007 1 次提交
-
-
由 Paul Mackerras 提交于
This updates all the defconfigs in arch/powerpc/configs except iseries and ps3, which were updated by the preceding commits. This mostly takes the defaults, except that I turned on tickless idle and high-resolution timers for everything, and turned off instrumentation support and "Fair group CPU scheduler" for the smaller/embedded platforms. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 17 10月, 2007 1 次提交
-
-
由 Anton Blanchard 提交于
When checking out the new NO_HZ support in powerpc, I noticed we never slept for more than 2 seconds. It turns out SLAB has a 2 second per cpu timer that causes this. After switching to SLUB I see some nice 4 second sleeps which is the limit on this POWER6 box (the decrementer ticks at 512MHz): slept 4.19 sec slept 4.19 sec slept 4.19 sec slept 4.19 sec slept 3.96 sec slept 3.80 sec slept 2.99 sec Since SLUB is now the default and some powerpc defconfigs already enable it, lets enable SLUB across the board for consistency. While doing this I also noticed that the maple defconfig has SLAB debugging enabled which is sure to make your box nice and slow. Fix that too. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 11 10月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 30 8月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 02 7月, 2007 1 次提交
-
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 22 1月, 2007 1 次提交
-
-
由 Paul Mackerras 提交于
Mostly took the defaults, except tried to get the netfilter options more or less as they were before. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 22 9月, 2006 1 次提交
-
-
由 Vitaly Bordug 提交于
This makes the 8560 evaluation board fully supported under arch/powerpc, as the first board with CPM2 SoC peripherals. The brand new devicetree nodes are introduced (intending to be a subset of the QuiccEngine-equipped models, with dts sources placed into the kernel according to the new convention. Assuming all the preceding stuff applied (PAL+fs_enet related+ CPM_UART update), the both TSEC eth ,FCC Eths, and both SCC UARTs are working. The relevant drivers are still capable to drive users in ppc, which was verified with 8272ADS (SCC uart+FCC eth). This is also verified on mpc8540 and actually make it work (PCI stuff working as well) Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
-
- 10 9月, 2006 1 次提交
-
-
由 Paul Mackerras 提交于
Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 05 4月, 2006 1 次提交
-
-
由 Andy Fleming 提交于
This patch adds support for 85xx CDS support to arch/powerpc Signed-off-by: NAndy Fleming <afleming@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 28 3月, 2006 1 次提交
-
-
由 Kumar Gala 提交于
When we build for the MPC8540 ADS produce a uImage by default. Updated the defconfig to reflect this as well. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 20 1月, 2006 1 次提交
-
-
由 Becky Bruce 提交于
Updated patch for support for mpc8540_ads in arch/powerpc with a flat OF device tree. This patch does not yet support PCI or I2C. Signed-off-by: NBecky Bruce <becky.bruce@freescale.com> Signed-off-by: NJon Loeliger <jdl@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 22 6月, 2005 1 次提交
-
-
由 Kumar Gala 提交于
Adds support for using the MPC8548 processor on the CDS reference board. Currently all the major busses (PCI, PCI-X, PCI-Express, sRIO) and eTSEC3 and eTSEC4 are not supported. Signed-off-by: NKumar Gala <kumar.gala@freescale.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 17 4月, 2005 1 次提交
-
-
由 Linus Torvalds 提交于
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
-