Provide an interface to the lower level driver to set the VHT
MU-MIMO data. This is needed for example when there is an update
of the group data during low power state, where the management
frame will not be passed to the host at all.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since the PNs of all the tx keys are now tracked in the public
part of the key struct (with atomic counter), we no longer
need these functions.

dvm and vt665{5,6} are currently the only users of these functions,
so update them accordingly.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If protocol offloading is configured, the fw might generate some
frames (e.g. arp response) on its own during d3/d0i3.

On d3/d0i3 exit the driver queries the updated PN (if relevant),
and updates its keys (for the d0i3 case, this is done by
iwl_mvm_d0i3_exit_work(), which is scheduled on d0i3 exit)

While in d0i3, iwlmvm defers tx frames until d0i3 exit, and
then continues their processing.

This is problematic with TKIP, since the frame's PN has already
been set at this stage (in contrast to CCMP, where the PN is
being set only later on), so both the frame's PN and the upcoming
PN update (from d0i3 exit work) might be wrong.

Fix it by moving the TX PN assignment (for TKIP) to the driver,
similarly to CCMP.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers/devices might want to set the IVs by
themselves (and still let mac80211 generate MMIC).

Specifically, this is needed when the device does
offloading at certain times, and the driver has
to make sure that the IVs of new tx frames (from
the host) are synchronized with IVs that were
potentially used during the offloading.

Similarly to CCMP, move the TX IVs of TKIP keys to the
public part of the key struct, and export a function
to add the IV right into the crypto header.

The public tx_pn field is defined as atomic64, so define
TKIP_PN_TO_IV16/32 helper macros to convert it to iv16/32
when needed.

Since the iv32 used for the p1k cache is taken
directly from the frame, we can safely remove
iv16/32 from being protected by tkip.txlock.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fix wiphy supported_band access in tx radiotap parsing introduced
in commit 5ec3aed9ba4c ("mac80211: Parse legacy and HT rate in
injected frames"). In particular, info->band is always set to 0
(IEEE80211_BAND_2GHZ) since it has not assigned yet.
This cause a kernel crash on 5GHz only devices.
Move ieee80211_parse_tx_radiotap() after info->band assignment
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This massively reduces data copying and thus improves rx performance
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

reuse_skb is set to true if the code decides to use the last segment.
Fixes a memory leak
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The source and destintation addresses in the memcpy arguments
are flipped. Fix that.

Fixes: 23a1f8d4("mac80211: process and save VHT MU-MIMO group frame")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mpp_path_del() and mesh_path_del() are mostly the same function.
Move common code into a new static function.
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NHenning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remember the last time when a mpp table entry is used for
rx or tx and remove them after MESH_PATH_EXPIRE time.
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NHenning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make the mesh_path_del() function remove all mpp table entries
that are proxied by the removed mesh path.
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NHenning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for 11ad devices.

Add support for PBSS by introducing a new PBSS flag attribute.
The PBSS flag is used in the START_AP command to request starting
a PCP instead of an AP, and in the CONNECT command to request
connecting to a PCP instead of an AP.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use skb_copy_bits in preparation for allowing fragmented skbs
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Prepararation for zero-copy A-MSDU support with page fragment SKBs
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

On error we jumped to the error label and returned the error code but we
missed releasing sinfo.

Fixes: 5fe74014172d ("mac80211: avoid excessive stack usage in sta_info")
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Number of deployed 80 MHz capable VHT stations that do not support 80+80
and 160 MHz bandwidths seem to misbehave when trying to connect to an AP
that advertises 80+80 or 160 MHz channel bandwidth in the VHT Operation
element. To avoid such issues with deployed devices, modify the design
based on recently accepted IEEE 802.11 standard changes (*).

This allows poorly implemented VHT 80 MHz stations to connect with the
AP in 80 MHz mode. 80+80 and 160 MHz capable stations need to support
the new workaround mechanism to allow full bandwidth to be used.
However, there are more or less no impacted station with 80+80/160
capability deployed.

The rebased version of this patch is based on the updated version from
Johannes Berg to take the HT/VHT chandef refactoring into account.

(*) Changes in
https://mentor.ieee.org/802.11/dcn/15/11-15-1530-04-000m-vht160-operation-signaling-through-non-zero-ccfs1.docx
were accepted during the IEEE 802.11 January 2016 meeting.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If any frames are dropped that are part of a BA session, the reorder
buffer will "indefinitely" (until the timeout) wait for them to come
in (or a BAR moving the window) and won't release frames after them.
This means it isn't possible to filter frames within a BA session in
firmware.

Introduce an API function that allows such filtering. Calling this
function will move the BA window forward to the new SSN, and allows
marking frames after the SSN as having been filtered, so any future
reordering activity will release frames while skipping the holes.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clean up ieee80211_rx_reorder_ready() callers by passing the RX
TID struct and the index, instead of the frames list. This will
make it more extensible as well.

While at it, move the inline to rx.c as it's only used there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow drivers to make more educated
decisions whether to defer transmission or not.

Relying on wake_tx_queue() call count implicitly
was not possible because it could be called
without queued frame count actually changing on
software tx aggregation start/stop code paths.

It was also not possible to know how long
byte-wise queue was without dequeueing.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers/devices without their own rate control algorithm can get the
information what rates they should use from either the radiotap header of
injected frames or from the rate control algorithm. But the parsing of the
legacy rate information from the radiotap header was removed in commit
e6a9854b ("mac80211/drivers: rewrite the rate control API").

The removal of this feature heavily reduced the usefulness of frame
injection when wanting to simulate specific transmission behavior. Having
rate parsing together with MCS rates and retry support allows a fine
grained selection of the tx behavior of injected frames for these kind of
tests.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The mean_chain_len field in struct mesh_table is copied whenever a
new mesh table is allocated, but only ever has the value 2 and is
never otherwise updated, so just remove it and use the related
define instead.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When CONFIG_OPTIMIZE_INLINING is set, the sta_info_insert_finish
function consumes more stack than normally, exceeding the
1024 byte limit on ARM:

net/mac80211/sta_info.c: In function 'sta_info_insert_finish':
net/mac80211/sta_info.c:561:1: error: the frame size of 1080 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

It turns out that there are two functions that put a 'struct station_info'
on the stack: __sta_info_destroy_part2 and sta_info_insert_finish, and
this structure alone requires up to 792 bytes.

Hoping that both are called rarely enough, this replaces the
on-stack structure with a dynamic allocation, which unfortunately
requires some suboptimal error handling for out-of-memory.

The __sta_info_destroy_part2 function is actually affected by the
stack usage twice because it calls cfg80211_del_sta_sinfo(), which
has another instance of struct station_info on its stack.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 98b62183 ("mac80211/cfg80211: add station events")
Fixes: 6f7a8d26 ("mac80211: send statistics with delete station event")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make sure there's at least a debug message whenever the
connection to the AP is terminated.

Also change one message from wiphy_debug() to the common
mlme_dbg().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When joining IBSS a full scan should be initiated in order to search
for existing cell, unless the fixed_channel parameter was set.
A default channel to create the IBSS on if no cell was found is
provided as well.
However - a scan is initiated only on the default channel provided
regardless of whether ifibss->fixed_channel is set or not, with the
obvious result of the cell not joining existing IBSS cell that is
on another channel.

Fixes: 76bed0f4 ("mac80211: IBSS fix scan request")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The timestamp given by iwlwifi is at the beginning of the
frame over the air, at (or during) the SYNC field. Allow
such timestamps to be given to mac80211, at least (for now)
for frames with non-HT/VHT preambles.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The ieee80211_queue_stopped() expects hw queue
number but it was given raw WMM AC number instead.

This could cause frame drops and problems with
traffic in some cases - most notably if driver
doesn't map AC numbers to queue numbers 1:1 and
uses ieee80211_stop_queues() and
ieee80211_wake_queue() only without ever calling
ieee80211_wake_queues().

On ath10k it was possible to hit this problem in
the following case:

  1. wlan0 uses queue 0
     (ath10k maps queues per vif)
  2. offchannel uses queue 15
  3. queues 1-14 are unused
  4. ieee80211_stop_queues()
  5. ieee80211_wake_queue(q=0)
  6. ieee80211_wake_queue(q=15)
     (other queues are not woken up because both
      driver and mac80211 know other queues are
      unused)
  7. ieee80211_rx_h_mesh_fwding()
  8. ieee80211_select_queue_80211() returns 2
  9. ieee80211_queue_stopped(q=2) returns true
 10. frame is dropped (oops!)

Fixes: d3c1597b ("mac80211: fix forwarded mesh frame queue mapping")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The driver can access the queue simultanously
while mac80211 tears down the interface. Without
spinlock protection this could lead to corrupting
sk_buff_head and subsequently to an invalid
pointer dereference.

Fixes: ba8c3d6f ("mac80211: add an intermediate software queue implementation")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove unnecessory "if" statement and club it with previos "if" block.
Signed-off-by: NSunil Shahu <shshahu@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a note to userspace on the effect of RFKILL_OP_CHANGE_ALL also
updating the default state for hotplugged devices.
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
[reword a bit]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This was scheduled to be removed in 2012 by:

 commit 69c86373
 Author: florian@mickler.org <florian@mickler.org>
 Date:   Wed Feb 24 12:05:16 2010 +0100

     Document the rfkill sysfs ABI

     This moves sysfs ABI info from Documentation/rfkill.txt to the
     ABI subfolder and reformats it.

     This also schedules the deprecated sysfs parts to be removed in
     2012 (claim file) and 2014 (state file).
Signed-off-by: NFlorian Mickler <florian@mickler.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

__rfkill_set_hw_state() is only one used in rfkill_set_hw_state(), and
none of them are long or complicated, so merging the two makes the code
easier to read.
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

RFKILL_BLOCK_SW value have just been saved to prev, no need to check it
again in the if expression. This makes code a little bit easier to read.
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NOla Olsson <ola.olsson@sonymobile.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When suspended while polling is paused, polling will erroneously
resume at resume time. Fix this by tracking pause and suspend in
separate state variable and adding the necessary checks.

Clarify the documentation on this as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The function here already has a variable hdr that even
contains the right thing, so the inner scope's hdr variable
that's shadowing the outer one can just be removed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make the addr parameter const in SET_IEEE80211_PERM_ADDR() to save
clients from having to cast away a const qualifier.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The station MLME and IBSS/mesh ones use entirely different
code for interpreting HT and VHT operation elements. Change
the code that interprets them a bit - it now modifies an
existing chandef - and use it also in the MLME code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Print a warning whenever an expected callback function
lacks implementation.
Signed-off-by: NOla Olsson <ola.olsson@sonymobile.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In VHT, the specification allows to limit the number of
MSDUs in an A-MSDU in the Extended Capabilities IE. There
is also a limitation on the byte size in the VHT IE.
In HT, the only limitation is on the byte size.
Parse the capabilities from the peer and make them
available to the driver.

In HT, there is another limitation when a BA agreement
is active: the byte size can't be greater than 4095.
This is not enforced here.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>