Signed-off-by: NDotan Barak <dotanb@mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If a SIDR REQ does not match a listen, we should reply with status
value 1 (service ID not supported), rather than dropping through to
the default case of status 2 (rejected by service provider).

Doing this also fixes a bug where the cm_id_priv is removed from the
remote_sidr_table twice.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix handling to duplicate SIDR REQs to avoid sending a reject if a
duplicate is detected.  Duplicates should just be silently discarded.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

cm_msgs.h uses definitions from ib_cm.h.  Include it directly, rather
than depending on a specific include order.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The IB CM should include the HCA ACK delay when calculating the local
ACK timeout value to use for RC QPs.  If the HCA ACK delay is large
enough relative to the packet life time, then if it is not taken into
account, the calculated timeout value ends up being too small, which
can result in "retry exceeded" errors.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The ib_cm is a little over zealous about using spin_lock_irqsave,
when spin_lock_irq would do.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

MADs sent to the SA should use the the default P_Key (0x7fff/0xffff).
There's no requirement that the default P_Key is stored at index 0 in
the local P_Key table, so add code to the sa_query module to look up
the index of the default P_Key when creating an address handle for the
SA (which is done any time the P_Key table might change), and use this
index for all SA queries.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

InfiniBand HCAs replicate multicast packets back to the QP that sent
them if that QP is attached to the destination multicast group.  This
means that IPoIB multicasts are often replicated back to the receive
queue of the interface that generated them.  To avoid confusing the
network stack, we drop these duplicates within the IPoIB driver.

However, there's no reason to free the skb that received the duplicate
and then immediately allocate a new skb to post to the receive queue.
We can be more efficient and just repost the same skb.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NShani Moideen <shani.moideen@wipro.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
----

Fix

    drivers/infiniband/ulp/ipoib/ipoib_cm.c:1151: warning: unused variable 'dev'

by getting rid of the variable dev, which is only used if CONFIG_IPV6
is enabled, and replacing the one use of it with the value it is
assigned, namely priv->dev.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When allocating out_mad in show_pma_counter(), take sizeof *out_mad
instead of sizeof *in_mad.  It is true that today the type of in_mad
and out_mad are the same, but this patch will give us a cleaner code.
Signed-off-by: NDotan Barak <dotanb@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Kick the hardware before unlocking the send/receive queue to overlap
processing a little more.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When firmware reports a nondisruptive port configuration change event,
previous versions of the eHCA driver didn't forward the event to consumers
like IPoIB.  Add code that determines the type of configuration change by
comparing old and new port attributes and reports it.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Also add two unlikely() statements.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This eliminates lock contention among IRQs as well as the need to
disable IRQs around idr_find, because there are no IRQ writers.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- ehca_cq.nr_events is made an atomic_t, eliminating a lot of locking.
- The CQ is removed from the CQ idr first now to make sure no more
  completions are scheduled on that CQ. The "wait for all completions to
  end" code becomes much simpler this way.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- Rename all spinlock flags to "flags", matching the vast majority of kernel
  code.
- Move hcall_lock into the only file it's used in.
- Replaced spin_lock_init() and friends with static initializers for
  global variables.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Support SRQs on eHCA2. Since an SRQ is a QP for eHCA2, a lot of code
(structures, create, destroy, post_recv) can be shared between QP and SRQ.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- Replace init_qp_queues() by a shorter init_qp_queue(), eliminating
  duplicate code.

- hipz_h_alloc_resource_qp() doesn't need a pointer to struct ehca_qp any
  longer. All input and output data is transferred through the parms
  parameter.

- Change the interface to also support SRQ.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In preparation for support of new eHCA2 features, change adapter probing:
 - Hardware level is changed to encode major and minor chip version
 - Hardware capabilities are queried from the firmware
 - The maximum MTU is queried from the firmware instead of assuming a
   fixed value
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Return the PortGUID of the correct port when responding to a NodeInfo
query.  Returning the SystemImageGUID causes issues when there are
multiple HCAs in a single system.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The changeset 3859e39d ("IB/ipath: Support larger IB_QP_MAX_DEST_RD_ATOMIC
and IB_QP_MAX_QP_RD_ATOMIC") added support for larger RD_ATOMIC values,
but it failed to take out the stricter checks that were before these and
hence had no effect.  This patch takes out the bogus checks....
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

All too often, interrupts do not get enabled for our card due to BIOS
misconfiguration and other issues.  This patch checks for that
condition on startup and warns the user.  This patch is based on work
(check LID availability) by Robert Walsh.
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Clean up some code by removing support for some older pre-production
HTX InfiniPath cards.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>

Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The default calculation for the number of send buffers to allocate to
the kernel was too high for the PCIe version of the chip thus leaving
fewer than desired send buffers for user MPI applications.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We are more careful to be sure that we don't lose information about
changes that occurred while we were in freeze mode, when the chip will
not notify us, and try to avoid false error interrupts while doing
cleanup.  Put all of this logic in a new function ipath_clear_freeze().
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a barrier to make sure the CPU doesn't reorder writes to memory,
since user programs can be polling on the head index update and the
entry should be written before that.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com>
[ Also remove cast from void * return of kmalloc() as suggested by  
  Jesper Juhl <jesper.juhl@gmail.com>. ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This bug results in an abort request being sent down _after_ the tid
has been released.  If the tid happens to have been reused, then the
subsequent generation of the tid gets incorrectly aborted.

The thread running iwch_accecpt_cr() must not abort a connection if an
error is returned after being awakened.  If any errors did occur while
iwch_accept_cr() is blocked, then the connection has already been
aborted on the thread processing the error.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The LLD does this for us in cxgb3_remove_tid().

Also fixed active open failure cases where we also shouldn't be
releasing the TID.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Negative advice messages should _not_ count toward the 2 abort
requests needed to indicate an abort request.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Don't set the gen bits nor length bits in the terminate WR.  This is
done by the LLD driver.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>