This patch properly set visible VRAM and enforce any pinned buffer
to be into visible VRAM. We might later add a flag to release this
constraint for some newer hw more clever than previous.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Get rid of _location and use _start/_end also simplify the
computation of vram_start|end & gtt_start|end. For R1XX-R2XX
we place VRAM at the same address of PCI aperture, those GPU
shouldn't have much memory and seems to behave better when
setup that way. For R3XX and newer we place VRAM at 0. For
R6XX-R7XX AGP we place VRAM before or after AGP aperture this
might limit to limit the VRAM size but it's very unlikely.
For IGP we don't change the VRAM placement.

Tested on (compiz,quake3,suspend/resume):
PCI/PCIE:RV280,R420,RV515,RV570,RV610,RV710
AGP:RV100,RV280,R420,RV350,RV620(RPB*),RV730
IGP:RS480(RPB*),RS690,RS780(RPB*),RS880

RPB: resume previously broken

V2 correct commit message to reflect more accurately the bug
and move VRAM placement to 0 for most of the GPU to avoid
limiting VRAM.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

this uses a new entrypoint to invalidate gart entries instead of using 0.
Changed to rather than pointing to 0 address point empty entry to dummy
page. This might help to avoid hard lockup if for some wrong
reasons GPU try to access unmapped GART entry.

I'm not 100% sure this is going to work, we probably need to allocate
a dummy page and point all the GTT entries at it similiar to what AGP does.
but we can test this first I suppose.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This already simplifies code significally and makes it maintaible
in case of adding memory reclocking plus voltage changing in future.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

V2: reorganize functions, fix modesetting calls
V3: rebase patch, use radeon's workqueue
V4: enable on tested chipsets only, request VBLANK IRQs
V5: enable PM on older hardware (IRQs, mode_fixup, dpms)
V6: use separate dynpm module parameter
V7: drop RADEON_ prefix, set minimum mode for dpms off
V8: update legacy encoder call, fix order in rs600 IRQ
V9: update compute_clocks call in legacy, not only DPMS_OFF
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Switch some magic numbers to their proper defines.
The register header madness needs to be cleaned up
at some point.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some servers have two VGA ports but only report
one in the bios connector tables.  On these systems
always set up the TV DAC so that it displays properly
even if the bios is wrong.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was
redondant.

Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Cache flush is required in case CPU is accessing rendered data.

This fixes glean/readPixSanity test case and random rendering
errors in sauerbraten and warzone2100.

v2 Fix comment ordering in r100_fence_ring_emit and remove extra
   defines added in first version.
Signed-off-by: NPauli Nieminen <suokkos@gmail.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The first dword of PACKET3_3D_DRAW_IMMD maps to
SE_VTX_FMT so the vertex size is part of the draw
packet.

This patch fixes a possible case where you have a
command buffer that does not contain SE_VTX_FMT
register write, but does contain PACKET3_3D_DRAW_IMMD.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Use same common function to disable agp so we replace the GART
callback by the proper one when we do so. This fix oops if
radeon_agp_init report failure.

This patch also move radeon_agp_init out of *_mc_init for r600
& rv770 so that we can have a similar behavior than for previous
hw, ie if agp_init fails it will fallback to GPU GART and disable
AGP.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If for any reason we haven't installed handler we shouldn't try to
enable IRQ/MSI on the hw so we don't get unhandled IRQ/MSI which
makes the kernel sad.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In some case we weren't releasing the AGP device at module unloading.
This leaded to unfunctional AGP at next module load. This patch make
sure we release the AGP bus if we acquire it.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

R300 family will hard lockup if host path read cache flush is
done through MMIO to HOST_PATH_CNTL. But scheduling same flush
through ring seems harmless. This patch remove the hdp_flush
callback and add a flush after each fence emission which means
a flush after each IB schedule. Thus we should have same behavior
without the hard lockup.

Tested on R100,R200,R300,R400,R500,R600,R700 family.

V2: Adjust fence counts in r600_blit_prepare_copy()
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Because hardware cannot disable all colorbuffers directly to do depth-only
rendering, a user should:
- disable reading from a colorbuffer in blending
- disable fastfill
- set the color channel mask to 0 to prevent writing to a colorbuffer
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds support for compressed textures to the r100->r500 CS
checker, it lets me run openarena and the demos in mesa fine.

Thanks to Maciej Cencora for initial comments.

Changes since v1:
fix calculations with Maciej formulas
Reviewed-by: NMaciej Cencora <m.cencora@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

On resume on my rv530 laptop surface cntl was left disabled, so
wierd stuff would happen with rendering to a tiled front buffer.

This checks if the surface regs are assigned to bos and reprograms
the surface registers on resume using the same path that clears
them all on init.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This enabled interrupt driven hpd support for all
radeon chips.  Assuming the hpd pin is wired up
correctly, the driver will generate uevents on
digital monitor connect and disconnect and retrain
DP monitors automatically.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This just adds the functionality, it's not hooked up
yet.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The DDX and radeonfb always set these regs to a sane value.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The locking & protection of radeon object was somewhat messy.
This patch completely rework it to now use ttm reserve as a
protection for the radeon object structure member. It also
shrink down the various radeon object structure by removing
field which were redondant with the ttm information. Last it
converts few simple functions to inline which should with
performances.

airlied: rebase on top of r600 and other changes.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We really don't need to process every irq that comes in, we only
really want to do SW irq processing when we are actually waiting for
a fence to pass. I'm not 100% sure this is race free esp on non-MSI systems
so it needs some testing.
Signed-off-by: NDave Airlie <airlied@redhat.com>

If we find a GPU but we can't find its BIOS and it isn't posted,
then ignore it.
Signed-off-by: NDave Airlie <airlied@redhat.com>

rendercheck under kms on r600s was failing due to HDP flushing not happening.

This adds HDP flushing to the object wait function for r100->r700 families.

rendercheck passes basic tests on r600 with this change.
Acked-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We might not hit this yet, but when if we do any sort of writeback
we really need to enable PCI bus mastering on these systems from
what I can see.

This enables PCI BM on all radeons that require it.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Immediate readback seems faulty on some chips.  I
suspect it takes a while to get through the fifo
to the actual register backbone.  There's no need
to read it back, so, just write the driver's copy
of the register's value directly.

Should fix bug 24535 and possibly 24218
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Try to enable msi on chips that support it.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The problem boils down to the order when the bit11
of the texture size is or'ed to the original width.
In the end each mipmap level has the same width or
height because of that 11 bit is ored to the scaled
down lod with and thus blows up the size again to the
full size or more due to the power of two rounding
afterwards.

The attached patch changes this order so that the
texture sizes are computed correct. Also the on error
the yet missing inputs to the size computation are
printed which helped me to find out where it really breaks.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMatt Turner <mattst88@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

While investigating the cause of CRTC FIFO underruns, I noticed that when
converting the memory bandwidth calculation from the userspace X driver code,
an instance of '8.0' was apparently accidentally converted to '80'.
Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Both r100/r600 had this wrong, use the macro to extract the register
to relocate.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also add single crtc for RN50 chips.

changes in v2:
fix vblank init to respect single crtc flag
fix r100 mode bandwidth to respect single crtc flag
Signed-off-by: NDave Airlie <airlied@redhat.com>

This remove old init path and allow code cleanup, now all hw
use the new init path, see top of radeon.h for description of
this.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

New init path allow to simply asic initialization and make easier
to trace what happen on each different asic. We are removing most
callback. More cleanup should happen latter to remove even more
callback. Also cleanup register specific to R100,RV200,RV250.
Version 2 correct the placement on IGP of the VRAM inside GPU address
space to match the stollen RAM placement of IGP.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also cleanup register specific to RS400/RS480. This patch also fix
legacy VGA register used to disable VGA access we were programming
wrong register. Now we should properly disable VGA on r100 up to
rs400 asics. Note that RS400/RS480 resume is broken, it hangs the
computer while reprogramming dynamic clock, doesn't work either
without that patch. We need to spend more time investigating this
issue. Version 2 of the patch remove dead code that was left
commented out in the previous version. Version 3 correct the
placement on IGP of the VRAM inside GPU address space to match the
stollen RAM placement of IGP.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- fix offset of NOP packet for parsing
- fix p->idx increments
- fix bad mask when updating crtc vline info
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

This avoids needing to do a kmalloc > PAGE_SIZE for the main
indirect buffer chunk, it adds an accessor for all reads from
the chunk and caches a single page at a time for subsequent
reads.

changes since v1:
Use a two page pool which should be the most common case
a single packet spanning > PAGE_SIZE will be hit, but I'm
having trouble seeing anywhere we currently generate anything like that.
hopefully proper short page copying at end
added parser_error flag to set deep errors instead of having to test
every ib value fetch.
fixed bug in patch that went to list.
Signed-off-by: NDave Airlie <airlied@redhat.com>

VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.

VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.

This patch comes from Fedora rawhide kernel.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>