FSG_NUM_BUFFERS is set to 2 as default.
Usually 2 buffers are enough to establish a good buffering pipeline.
The number may be increased in order to compensate a for bursty VFS
behaviour.

Here follows a description of system that may require more than
2 buffers.
 * CPU ondemand governor active
 * latency cost for wake up and/or frequency change
 * DMA for IO

Use case description.
 * Data transfer from MMC via VFS to USB.
 * DMA shuffles data from MMC and to USB.
 * The CPU wakes up every now and then to pass data in and out from VFS,
   which cause the bursty VFS behaviour.

Test set up
 * Running dd on the host reading from the mass storage device
 * cmdline: dd if=/dev/sdb of=/dev/null bs=4k count=$((256*100))
 * Caches are dropped on the host and on the device before each run

Measurements on a Snowball board with ondemand_governor active.

FSG_NUM_BUFFERS 2
104857600 bytes (105 MB) copied, 5.62173 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.61811 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.57817 s, 18.8 MB/s

FSG_NUM_BUFFERS 4
104857600 bytes (105 MB) copied, 5.26839 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2691 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2711 s, 19.9 MB/s

There may not be one optimal number for all boards. This is why
the number is added to Kconfig. If selecting USB_GADGET_DEBUG_FILES
this value may be set by a module parameter as well.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The ARCH_MX1 scheduled for removal. Instead, depend on ARCH_MXC
and make clear in the Kconfig text that only i.MX1 has this
hardware.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.

Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.

The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.

More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.

While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.

[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After 62285963 (usb: musb: drop a gigantic amount of ifdeferry):

 - USB_GADGET_MUSB_HDRC is no longer selectable because it
   depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
   options

 - The Kconfig comment still says "Enable Host or Gadget support
   to see Inventra options", even though you now need to enable
   both of them to see Inventra options.

Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch rescues renesas_usbhs compile from
commit 193ab2a6 (usb: gadget: allow multiple gadgets to be built)

CONFIG_USB_RENESAS_USBHS compile renesas_usbhs main code which
is shared between Host/Gadget.
CONFIG_USB_RENESAS_USBHS_UDC add mod_gadget to it.

It had lost USB_GADGET_DUALSPEED
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Both fusb300 and langwell udcs seem to only
work with 32-bit address space.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

now that we have the udc class, we can allow
multiple gadget controller drivers to be
compiled as modules. This will allow for
distro-like kernels for embedded devices.

With this patch, I managed to build an x86
kernel with support for many of the controllers
enabled:

CONFIG_USB_FUSB300=m
CONFIG_USB_R8A66597=m
CONFIG_USB_M66592=m
CONFIG_USB_AMD5536UDC=m
CONFIG_USB_CI13XXX_PCI=m
CONFIG_USB_NET2272=m
CONFIG_USB_NET2280=m
CONFIG_USB_GOKU=m
CONFIG_USB_LANGWELL=m
CONFIG_USB_EG20T=m

Also an ARM kernel with support for many controllers:

CONFIG_USB_FUSB300=m
CONFIG_USB_OMAP=m
CONFIG_USB_R8A66597=m
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_M66592=m
CONFIG_USB_NET2272=m
CONFIG_USB_DUMMY_HCD=m

The next step would be to get rid of the
direct access to arch/ and mach/ directories
on some gadget controllers so that we can
build all of them without depending on their
respective ARCH_* symbols.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds SS support to the dummy hcd module.
It may be used to test SS device when no (SS) HW is
available.

USB 3.0 hub includes 2 hubs - one HS and one SS. This
patch adds support for a SS root hub in the dummy_hcd
module.

A new module parameter was added: is_super_speed. When
set to true, a SS root hub will also be registered and
the connected device will be enumerated over the SS
root hub. The default of this parameter is false.
Signed-off-by: NTatyana Brokhman <tlinder@codeaurora.org>

[ balbi@ti.com : slight change to commit log
		 fixed one coding style issue ]
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

SuperSpeed USB has defined a new descriptor, called
the Binary Device Object Store (BOS) Descriptor. It
has also changed a bit the definition of SET_FEATURE
and GET_STATUS requests to add USB3-specific details.

This patch implements both changes to the Composite
Gadget Framework.

[ balbi@ti.com : slight changes to commit log
		 fixed a compile error on ARM ]
Signed-off-by: NTatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1471) deprecates the File-backed Storage Driver and
schedules its replacement for the 3.8 kernel release (about two years
from now).  Users are advised to switch to the Mass Storage Gadget
instead.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1468) changes the Kconfig definition for
USB_GADGET_DUALSPEED.  This option is determined entirely by which
device controller drivers are to be built, through Select statements;
it does not need to be (and should not be) configurable by the user.

Also, the "default n" line is superfluous -- everything defaults to N.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is based on the last release from PLX:
	http://www.plxtech.com/files/products/net2000/software/selectiontool/RE061204-net2272-linux2.6.18.tgz

I've managed to contact them and they've confirmed that this driver was
wholly written by PLX (Seth Levy).  While they have no problem with it
being merged (and they've already licensed it as GPL), they don't have
any interest in doing so themselves as this is an old part for them.

ADI has long had an add-on card which has this part on it, so we've been
keeping it up-to-date out of tree.  But now that PLX has confirmed the
source of the driver, we can can take the next step of cleaning it up and
getting it merged.

So here we are!  I've done quite a large clean up of the driver and
attempted to address all the common issues.  Hopefully in the process,
I haven't broken anything.  While it seems to still work with the board
that I have access to, it is not a PCI variant.  So I have not tested
any of the PCI logic myself (beyond clean compile).  Perhaps someone who
actually has a card and cares can do so.

I'll try to address further feedback, but don't expect miracles.  I'm
not really familiar with the part itself, just the platform glue.
Signed-off-by: NSeth Levy <seth.levy@plxtech.com>
Signed-off-by: NAsh Aziz <ash.aziz@plxtech.com>
Signed-off-by: NRoy Huang <roy.huang@analog.com>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Samsung's S3C2416, S3C2443 and S3C2450 includes a USB High-Speed
device controller module. This driver enables support for USB high-speed
gadget functionality for the Samsung S3C24xx SoC's that include this
controller.
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NSangbeom Kim <sbkim73@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NAlexander Neumann <alexander@bumpern.de>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch add usb gadget code to SuperH USBHS.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver is used across all MSM SoCs.  Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below compilation errors.

  CC      drivers/usb/gadget/ci13xxx_msm.o
  CC      net/mac80211/led.o
  drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
  drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
  drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
  drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
  drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2

MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

lh7a40x has only been receiving updates for updates to generic code.
The last involvement from the maintainer according to the git logs was
in 2006.  As such, it is a maintainence burden with no benefit.

This gets rid of two defconfigs.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

USB2.0 device controller driver for Faraday fubs300
Signed-off-by: NYuan-Hsin Chen <yhchen@faraday-tech.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Support new device OKI SEMICONDUCTOR's ML7213 IOH(Input/Output Hub) which is for
IVI(In-Vehicle Infotainment) use.
The ML7213 is companion chip for Intel Atom E6xx series.
The ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patches makes possible to use composite framework and f_ncm
NCM function driver to build a standalone NCM gadget device.
Signed-off-by: NYauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

MSM SoC has chipidea USB controller. So use ci13xxx_udc core.
This driver depends on transceiver driver for clock control,
PHY initialization, VBUS detection.  Register for notify_event
callback to perform MSM specific quirks after controller is reset
and stopped.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move PCI bus code from ci13xxx_udc to a new file ci13xxx_pci.  SoC's
which has MIPS USB core can include the ci13xxx_udc and keep bus glue
code in their respective gadget controller drivers.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch add USB client support Marvell PXA9xx/PXA168 chips. The USB
controller in PXA9xx/PXA168 is a High-Speed OTG controller. The available
endpoints is different between PXA9xx and PXA168.

NOTE:
It is the first version of Marvell PXA9xx/PXA168 USB controller driver.
The support for OTG mode will be added in later patch.
PXA9xx and PXA168 has integrated UTMI PHY in the chips. The initialization
for the PHY is a little different between PXA9xx and PXA168.
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the USB device driver of EG20T(Topcliff) PCH.

EG20T PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
EG20T PCH are actually devices sitting on AMBA bus.
EG20T PCH has USB device I/F. Using this I/F, it is able to access system
devices connected to USB device.
Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Acked-by: NMichał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 126512e3 added support for FSL's USB
controller on powerpc. In this commit the Open Firmware code was selected
and compiled unconditionally.

This breaks on ARM systems from FSL which use the same driver (.i.e. the i.MX
series), because ARM don't have OF support (yet). This patch fixes the problem
by only selecting the OF code on systems with Open Firmware support.
Reported-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Compile-Tested-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

warning: (USB_MUSB_HDRC_HCD && USB_SUPPORT && USB_MUSB_HDRC &&
(USB_MUSB_HOST || USB_MUSB_OTG) && USB_GADGET_MUSB_HDRC || USB_MUSB_OTG
&& <choice> && USB && USB_GADGET && PM && EXPERIMENTAL) selects USB_OTG
which has unmet direct dependencies (USB_GADGET_OMAP && ARCH_OMAP_OTG &&
USB_OHCI_HCD)

This doesn't seem to happen on 2.6.36-rc8, but still doesn't make sense
to keep this duplicated config that is already defined in usb/core.
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.

The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It's spelled "Function Filesystem" / "FunctionFS". This patch
fixes some typos (FunctioFS->FunctionFS, Funcion->Function,
funcion->function, redundant "as") in the Kconfig description of
USB_FUNCTIONFS*.
Signed-off-by: NMichael Prokop <mika@grml.org>
Acked-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a patch that implements an USB EHCI Debug Device using the
Gadget API. This patch applies to a 2.6.35-rc3 kernel.

The gadget needs a compliant usb controller that forwards the
USB_DEVICE_DEBUG_MODE feature to its gadget.

The gadget provides two configuration modes, one that only printk() the
received data, and one that exposes a serial device to userland
(/dev/ttyGSxxx).

The gadget has been tested on an IGEPv2 board running a 2.6.35-rc1
kernel. The debug port was fed on the host side by a 2.6.34 kernel.
Signed-off-by: NStephane Duverger <stephane.duverger@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This commit cleans the g_fs gadget hopefully making it more
readable.  This is achieved by usage of the usb_string_ids_tab()
function for batch string IDs registration as well as
generalising configuration so that a single routine is
used to add each configuration and bind interfaces.  As an
effect, the code is shorter and has fewer #ifdefs.

Moreover, in some circumstances previous code #defined
CONFIG_USB_FUNCTIONFS_GENERIC macro to prevent a situation
where gadget with no configurations is built.  This code removes
the #define form source code and achieves the same effect using
select in Kconfig.

This patch also changes wording and names of the Kconfig options.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Multifunction Composite Gadget have been cleaned up
and refactored so hopefully it looks prettier and works
at least as good as before changes.

A Kconfig has also been fixed to make it impossible to build
FunctionFS gadget with no configurations.  With this patch, if
RNDIS is not chosen by the user CDC is force-selected.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The s3c_hsotg driver sets usb_gadget->is_dualspeed to 1, yet it doesn't define
USB_GADGET_DUALSPEED in Kconfig. This triggers a NULL pointer dereference in
the composite driver (which is fixed in another patch).
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix functionfs build to handle CONFIG_NET not enabled, to prevent
these build errors:

ERROR: "netif_carrier_on" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "netif_carrier_off" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "skb_realloc_headroom" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "skb_trim" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "netif_rx" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "alloc_etherdev_mq" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "ethtool_op_get_link" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "free_netdev" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "register_netdev" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "skb_push" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "skb_pull" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "dev_kfree_skb_any" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "skb_queue_tail" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "__alloc_skb" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "eth_type_trans" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "eth_validate_addr" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "skb_dequeue" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "unregister_netdev" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "__netif_schedule" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "skb_put" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "eth_mac_addr" [drivers/usb/gadget/g_ffs.ko] undefined!
ERROR: "dev_get_stats" [drivers/usb/gadget/g_ffs.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NMichał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Function Filesystem (FunctioFS) lets one create USB
composite functions in user space in the same way as GadgetFS
lets one create USB gadgets in user space.  This allows
creation of composite gadgets such that some of the functions
are implemented in kernel space (for instance Ethernet, serial
or mass storage) and other are implemented in user space.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

g_webcam uses v4l[2] interfaces, so it should depend on VIDEO_DEV.

ERROR: "v4l2_event_unsubscribe" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "v4l2_event_queue" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "video_device_release" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "video_usercopy" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "v4l2_event_dequeue" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "video_register_device" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "video_device_alloc" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "v4l2_event_subscribe" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "video_unregister_device" [drivers/usb/gadget/g_webcam.ko] ndefined!
ERROR: "v4l2_event_pending" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "v4l2_fh_init" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "v4l2_event_init" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "video_devdata" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "v4l2_event_alloc" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "v4l2_fh_add" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "v4l2_fh_del" [drivers/usb/gadget/g_webcam.ko] undefined!
ERROR: "v4l2_fh_exit" [drivers/usb/gadget/g_webcam.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This webcam gadget instantiates a UVC camera (360p and 720p resolutions
in YUYV and MJPEG).
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

g_hid is a USB gadget driver implementing the Human Interface Device class
specification. The driver handles basic HID protocol handling in the
kernel, and allows userspace to read/write HID reports trough /dev/hidgX
character devices.
Signed-off-by: NFabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: NPeter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Kconfig help message for Mass Storage Gadget claimed the
module will be named "g_file_storage" whereas it should be
"g_mass_storage".
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

g_nokia is the gadget driver implementing
WMCDC Wireless Handset Control Model for the N900
device.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB_G_MULTI uses block and net interface functions, so make it
depend on both of those.  Otherwise there are lots of build errors.

Fix USB_G_MULTI config help text typos and copy/paste error.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>