This patch adds support for the integrated NAND flash controller of the
TXx9 family.

Once upon a time there were tx4925ndfmc and tx4938ndfmc driver.  They
were removed due to bitrot in 2005.
This new driver is completely rewritten based on a driver in CELF patch
archive.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Bächle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This is a device driver for the NAND flash controller found on the various
DaVinci family chips.  It handles up to four SoC chipselects, and some
flavors of secondary chipselect (e.g.  based on upper bits of the address
bus) as used with some multichip packages.  (Including the 2 GiB chips
used on some TI devel boards.)

The 1-bit ECC hardware is supported (3 bytes ECC per 512 bytes data); but
not yet the newer 4-bit ECC (10 bytes ECC per 512 bytes data), as
available on chips like the DM355 or OMAP-L137 and needed with the more
error-prone MLC NAND chips.

This is a cleaned-up version of code that's been in use for several years
now; sanity checked with the new drivers/mtd/tests.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The current ndfc driver only compiles under arch/ppc. This arch was
removed from the kernel. I notice the event entry for the ndfc in
Kconfig has been removed in 2.6.28.

This patch converts the ndfc to a proper OF (OpenFirmware) driver. I
can give a working example of the DTS if needed.

The patch has been in production use on the PIKA Warp Appliance and is
in use by others. The Warp basically boots from NAND, so the ndfc driver
is very important to us.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Acked-By: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Not all architectures provide readsb(). We should probably move to using
ioread8_rep() instead.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The patch adds support for NAND flashes connected to GPIOs.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Several Renesas SuperH CPU has FLCTL. The FLCTL support NAND Flash.
This driver support SH7723.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Removed the Kconfig associated with 'NDFC NanD Flash Controller'.
We can't enable !CONFIG_PPC_MERGE so there is no way to enable
this.  Additionally the code needs to get updated for arch/powerpc.

For the time being lets just remove the Kconfig option so we can
actually remove CONFIG_PPC_MERGE.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch extends the FSL UPM NAND driver from Anton Vorontsov to
support hardware which does not have the R/B pin of the NAND chip
connected, like the TQM8548 module:

- The OF_GPIO dependency has been removed from the Kconfig option
  because GPIO is not needed. The relevant gpio_* function are then
  stubbed out in <linux/gpio.h>.

- It re-introduces the chip-delay property to define an appropriate
  maximum delay time (tR) required for read operations. The binding
  will be documented in a separate patch.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds support for the integrated NAND flash controller of the
i.MX2 and i.MX3 family. It is tested on MX27 but should work on MX3
aswell.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NJuergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds a MTD_NAND_PXA3xx_BUILTIN configuration variables which
allows to disable usage of builtin flash-type table.  Not enabling this
option saves some space in the generated driver.
Signed-off-by: NEnrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The TMIO chips are only found (and thus tested) on ARM machines.
Moreover, we don't want the TMIO cells to be built if one of the TMIO
driver is not selected (which indirectly make the TMIO cells drivers
depend on ARM as well).
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

This patch adds support for the NAND controller commonly found in
TMIO based MFDs.
Signed-off-by: NIan Molton <spyro@f2s.com>
Acked-By: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>

This was a reference board for which support never got merged upstream.
Kill it off, at rmk's suggestion.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

There's no reason to prevent the Atmel NAND driver from
building as a module.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Make the atmel_nand driver selectable on AVR32, and update the Kconfig
help text to reflect this.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The AT91 NAND driver needs just a few tiny modifications to work on
AVR32 as well. Rename it atmel_nand to reflect this.

Also move the ECC register definitions into drivers/mtd/nand since they
are only useful to the atmel_nand driver, and get rid of the useless
filename at the top of each file.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Once upon a time, the MTD repository was using CVS.

This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.

This also includes code that printed them to the user.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is a patch to use the hardware ECC controller of
the AT91SAM9260 and AT91SAM9263 for the AT91 nand.
On AT91 NAND, there's now a choice between ECC soft,
ECC hard or no ECC (for debug).

It has been tested on AT91SAM9263 with 8 bits large
and small page NAND.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is very simple driver, NAND is connected through localbus,
and User-Programmable Machine is doing various adjustments to
speak NAND. No special efforts needed to do read and write cycles,
though to control ALE and CLE phases, we ask UPM to generate exact
pre-programmed signals on the localbus lines.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is preliminary since:

1. It supports only _one_ chip select at the moment. As there is no
   existing platforms available using two chip selects of the NAND
   controller, it shall really not include code for supporting the
   2nd chip select for now, as such code cannot be verified.

2. It resorts to the default and simpliest memory based badblock
   table

3. Only limited types of nand flash are currently supported. Most
   PXA3xx processors come with on-chip NAND flash dies, so there
   isn't much flexibility for other types of NAND.

4. The NAND controller should be configured to detect the device's
   ID, thus making it difficult to use nand_scan_ident() to assist
   the detection process (though it's not impossible)

TODO: fix all the above limitations of cuz :-)
Signed-off-by: Neric miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NNick Spence <nick.spence@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Driver for the device bus NAND controller in the Marvell Orion family
of ARM SoCs.
Signed-off-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NJörn Engel <joern@logfs.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Plumbing for NAND connected via localbus on PA Semi PWRficient-based
boards.

From: Egor Martovetsky <egor@pasemi.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJoern Engel <joern@logfs.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is the driver for latest Blackfin on-chip nand flash controller

 - use nand_chip and mtd_info common nand driver interface
 - provide both PIO and dma operation
 - compiled with ezkit bf548 configuration
 - use hardware 1-bit ECC
 - tested with YAFFS2 and can mount YAFFS2 filesystem as rootfs

ChangeLog from try#1
 - use hweight32() instead of count_bits()
 - replace bf54x with bf5xx and BF54X with BF5XX
 - compare against plat->page_size in 2 cases when enable hardware ECC

ChangeLog from try#2
 - passed nand_test suites
 - use cpu_relax() instead of busy wait loop
 - some coding style issue pointed out by Andrew
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Unlike most stuff on the market the chip inside these two allows raw
flash access and doesn't implement and FTL, leaving that functionality
to the device driver.

Raw flash access in a cheap USB cardreader!  An MTD test device one can
attach to a PC!  What a deal!

The command set of the chip is not documented, so information was
obtained from the existing mass-storage driver
(drivers/usb/storage/alauda.c), its documentation
(http://alauda.sourceforge.net/wikka.php?wakka=BulkCommandReference),
additional reverse engineering and comparison with a vendor driver for a
related chip
(http://www.ratocsystems.com/english/download/driver/linux/sma03u.html).
Signed-off-by: NJoern Engel <joern@logfs.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

These drivers are specific to 4xx support in arch/ppc at the moment.  Make
sure they don't get built on arch/powerpc.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The price might drop to $100 in a few years.

But currently, a more reasonable name might be "$175 laptop".

Let's simply call it "OLPC laptop" without any price tag.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This patch adds 405 platform support to the 440 NDFC driver. The new
AMCC 405EZ PPC is equipped with the same NDFC core as the 440EP(x)
and other will follow soon.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This patch adds support for generic platform NAND driver.
Updated after tglx's review/discussion in IRC #mtd channel.
Signed-off-by: NVitaly Wool <vitalywool@gmail.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NSegher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This patch provides MTD support for NAND flash devices on CM-x270 modules.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is a nand flash driver for the eXcite series of intelligent
cameras manufactured by Basler Vision Technologies AG.
Signed-off-by: NThomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>