Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes kernel panic while ISO IN transfer is aborted.Replaced
usb_hcd_unlink_urb_from_ep() from musb_giveback() to __musb_giveback()
to make sure urb is unlinked before giveback when __musb_giveback() is
called from musb_urb_dequeue().

Acquired musb->lock() before usb_hcd_unlink_urb_from_ep() within in
enqueue path.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes enumeration failures when a USB device attached to a LS hub is
connected to OMAP EVM via HS hub. This is fixed by correctly
programming hub address register in enqueue path.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For those archs which don't provide read/write friends we
provide our own implementation so musb driver won't break
compilation.

This is temporary fix until a better solution comes from
upstream. Idealy, <linux/io.h> would provide those calls
if the architecture did not provide them yet. In that case
being possible to remove all those stubs from musb_io.h
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The new composite framework revealed a weakness in the
s3c2410_udc driver gadget register function. Instead of
checking if speed asked for was USB_LOW_SPEED upon
usb_gadget_register() to deny service, it checked only
for USB_FULL_SPEED, thus denying service to usb high
speed capable gadgets (like g_ether).
Signed-off-by: NYauhen Kharuzhy <jekhor@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Offer a "how much VBUS power to request" configuration option
for USB gadgets that aren't using board-specific customization
of their gadget or (composite) configuration drivers.

Also remove a couple pointless "depends on USB_GADGET" bits
from the Kconfig text; booleans inside an "if USB_GADGET" will
already have that dependency.

Based on a patch from Justin Clacherty.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Justin Clacherty <justin@redfish-group.com>
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is no check if platform code passes in more endpoints (num_eps)
than the maximum number of enpoints (MUSB_C_NUM_EPS.)  The result is
that allocate_instance() happily writes past the end of 'struct musb'
corrupting memory.

This patch adds a BUG() if the platform code requests more than the max.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove
the dead code associated with !CONFIG_PPC_MERGE.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usbmon registers the notifier chain, takes the bus lock and then goes to
scan the existing devices for hooking up.

Unfortunately, if usb_mon gets initialized while USB bus discovery is
going on, it's possible that usbmon gets a notifier on one cpu (which runs
without USB locks), and the scan is going on and also finds the new bus,
resulting in a double sysfs registration, which then produces a WARNING.

Pete Zaitcev did the bug diagnostics on this one
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Acked-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1137) changes the hub_activate() routine, replacing the
power-power-up and debounce delays with delayed_work calls.  The idea
is that on systems where the USB stack is compiled into the kernel
rather than built as modules, these delays will no longer block the
boot thread.  At least 100 ms is saved for each root hub, which can
add up to a significant savings in total boot time.

Arjan van de Ven was very pleased to see that this shaved 700 ms off
his computer's boot time.  Since his total boot time is on the order
of two seconds, the improvement is considerable.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NArjan van de Ven <arjan@infradead.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fix 2 problems about reading periodic file:

1. The "..." after a interrupt qh is missed because buffer pointer is
   not moved.

2. After setting p.ptr as NULL, its next qh or itd will be omited and
   can't be stored in debug buffer.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is based on the following ideas:

1. Some usb devices (such as usb video class) have endpoints of high
   interval attribute, so reading "periodic" file need more debug buffer
   to accommodate the qh or itd schedule information.  For example, 4KB
   buffer is not enough for a single interrupt qh of 2ms period.

2. print a %p need 16 byte buffer on 64-bits arch, but 8 byte on 32-bits
   arch. Add a extra bonus for 64-bits arch.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Try to workaround issues with bad SCSI implementations
by ignoring the command size error.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

g_printer doesn't have to check whether the data size is a multiple of
MaxPacketSize, because device controller driver already make that check.

Signed-off-by: SangSu Park<sangsu@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes a minor typo in the comments for usb_set_serial_data.
Signed-off-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Correct errors in the descriptions for usb_autopm_enable
and usb_autopm_disable in the USB PM doc.
Signed-off-by: NGeoff Levand <geoff@infradead.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves dbg calls to dev_dbg where possible. It also fixes some
issues with a previous submission aiming to do the same thing.
Signed-off-by: NKevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reset upon resumption will wipe the input buffer and is therefore
a reason to not suspend if remote wakeup is requested because
the driver needs that data.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds Documentation for the extensions of the anchor API.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1134) attempts to improve the way we handle OHCI
controllers with broken Root Hub Status Change interrupt support.  In
these controllers the RHSC interrupt bit essentially never turns off,
making RHSC interrupts useless -- they have to remain permanently
disabled.

Such controllers should still be allowed to turn off their root hubs
when no devices are attached.  Polling for new connections can
continue while the root hub is suspended.  The patch implements this
feature.  (It won't have much effect unless CONFIG_PM is enabled and
CONFIG_USB_SUSPEND is disabled, but since the overhead is very small
we may as well do it.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1118) addresses a problem with certain USB mass-storage
devices.  These devices sometimes return less data than asked for and
then provide no sense data to explain the problem.  Currently
usb-storage leaves it up to the SCSI layer to decide how this should
be handled, and the SCSI layer interprets the lack of sense data to
mean that nothing went wrong.  But if we got less data than required
then something definitely _did_ go wrong, and we should say so.

The patch tells the SCSI layer to retry the command when this sort of
thing happens.  Retrying may not solve the underlying problem, but
it's better than believing that data was transferred when it wasn't.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some of Freescale SoC chips have a QE or CPM co-processor which
supports full speed USB.  The driver adds device mode support
of both QE and CPM USB controller to Linux USB gadget.  The
driver is tested with MPC8360 and MPC8272, and should work with
other models having QE/CPM given minor tweaks.
Signed-off-by: NXie Xiaobo <X.Xie@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In case of error, the function backlight_device_register returns an
ERR pointer, but never returns a NULL pointer. So a NULL test that may
come after a call to this function should be strengthened by an IS_ERR
test.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@match_bad_null_test@
expression x, E;
statement S1,S2;
@@
x = backlight_device_register(...)
... when != x = E
* if (x != NULL) 
S1 else S2
// </smpl>
Signed-off-by: NJulien Brunel <brunel@diku.dk>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
  drivers/usb/gadget/pxa27x_udc.c

This patch removes the said #include <version.h>.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some USB peripheral controller drivers support software control
over the data pullup.  Use those controls to prevent the OBEX
function from enumerating until the userspace server has opened
the /dev/ttyGS* node it will use to implement protocol chitchat
with the USB host.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The following patch introduces a new f_obex.c function driver.
It allows userspace obex servers to use usb as transport layer
for their messages.

[ dbrownell@users.sourceforge.net: various fixes and cleanups ]
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a new mechanism to the composite gadget framework, letting
functions deactivate (and reactivate) themselves.  Think of it
as a refcounted wrapper for the software pullup control.

A key example of why to use this mechanism involves functions that
require a userspace daemon.  Those functions shuld use this new
mechanism to prevent the gadget from enumerating until those daemons
are activated.  Without this mechanism, hosts would see devices that
malfunction until the relevant daemons start.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1132) implements the set_wedge() method for net2280.
This method is necessary for strict USBCV compliance in
g_file_storage.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1131) implements the set_wedge() method for dummy_hcd.
This method is necessary for strict USBCV compliance in
g_file_storage.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reorders the list of USB peripheral controller drivers so it's
more common for the initial (default) value to be relevant:  put the
SOC integrated silicon up front, discrete stuff last.  Alphabetize.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

[This version fixes a thinko in the r8a66597 driver]

This patch let a few discrete USB host controllers drivers (isp116x-hcd,
r8a66597-hcd and sl811-hcd) obtain IRQ flags from their IORESOURCE_IRQ
resource if configured as such, much like it's been done for the smc91x
driver.

It spares people writing support for specific boards the burden to
configure the interrupt controller independantly, and keeps all IRQ
related information in a single resource.

HCD that are integrally part of a SoC have been left aside, as there
is probably no "wiring" options...

Tested on an Xscale PXA-255 based platform with isp116x-hcd.
Signed-off-by: NMarc Zyngier <marc.zyngier@altran.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove forgotten code related to sg_stat[].
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this extends the poisoning concept to anchors. This way poisoning
will work with fire and forget drivers.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

looking at usb_kill_urb() it seems to me that it is unnecessarily lenient.
In the use case of disconnect() you never want to use the URB again
(for the same device) But leaving urb->reject elevated will make it easier
to avoid races between read/write and disconnect.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In this code, it is possible to tell statically whether usblp will be NULL
in the error handling code.

Oliver Neukum suggested to make a goto to the final return rather than 
return directly.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
identifier f,err,l,l1;
type T;
expression x,E;
statement S;
@@

x = NULL
... when != goto l1;
* x = f(...)
... when != x
err = E;
goto l;
...
* if (x != NULL)
  S
return err;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver was originaly written by Stefan Kopp, but massively
reworked by Greg for submission.

Thanks to Felipe Balbi <me@felipebalbi.com> for lots of work in cleaning
up this driver.

Thanks to Oliver Neukum <oliver@neukum.org> for reviewing previous
versions and pointing out problems.


Cc: Stefan Kopp <stefan_kopp@agilent.com>
Cc: Marcel Janssen <korgull@home.nl>
Cc: Felipe Balbi <me@felipebalbi.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added basic support for a Delcom USB 7-segment LED Display

Signed-off by: Harrison Metzger <harrisonmetz@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add Oceanic PID to ftdi_sio driver

Oceanic dive computers (such as the VT3 --
http://www.oceanicworldwide.com/p_computers_vt3.html) all use an onboard
FTDI serial converter, with the FTDI vid and a  PID of 0xf460.  The
attached patch adds that pid to ftdi_sio; driver  connects to my VT3
after that.
Signed-off-by: NVladimir Vukicevic <vladimir@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>