Previously, the driver queried the firmware in order to get the number
of supported EQs. Under SRIOV, since this was done before the driver
notified the firmware how many VFs it actually needs, the firmware had
to take into account a worst case scenario and always allocated four EQs
per VF, where one was used for events while the others were used for completions.

Now, when the firmware supports the asymmetric allocation scheme, denoted
by exposing num_sys_eqs > 0 (--> MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the
QUERY_FUNC command to query the firmware before enabling SRIOV. Thus we
can get more EQs and MSI-X vectors per function.

Moreover, when running in the new firmware/driver mode, the limitation
that the number of EQs should be a power of two is lifted.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QUERY_FUNC firmware command could be used in order to query the
number of EQs, reserved EQs, etc for a specific function.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We've used an incorrect type for the loop counter and the
mlx4_QUERY_FUNC_CAP function. The current input modifier
is either a port or a boolean.
Since the number of ports is always a positive value < 255,
we should use u8 instead of an integer with casting.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This feature is intended for archs having cache line larger then 64B.

Since our CQE/EQEs are generally 64B in those systems, HW will write
twice to the same cache line consecutively, causing pipe locks due to
he hazard prevention mechanism. For elements in a cyclic buffer, writes
are consecutive, so entries smaller than a cache line should be
avoided, especially if they are written at a high rate.

Reduce consecutive writes to same cache line in CQs/EQs, by allowing the
driver to increase the distance between entries so that each will reside
in a different cache line. Until the introduction of this feature, there
were two types of CQE/EQE:

1. 32B stride and context in the [0-31] segment
2. 64B stride and context in the [32-63] segment

This feature introduces two additional types:

3. 128B stride and context in the [0-31] segment (128B cache line)
4. 256B stride and context in the [0-31] segment (256B cache line)

Modify the mlx4_core driver to query the device for the CQE/EQE cache
line stride capability and to enable that capability when the host
cache line size is larger than 64 bytes (supported cache lines are
128B and 256B).

The mlx4 IB driver and libmlx4 need not be aware of this change. The PF
context behaviour is changed to require this change in VF drivers
running on such archs.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds the infrastructure for enabling selected VFs to
operate SMI (QP0) MADs without restriction.

Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs
are MLX QPs.  As such, they operate over VL15.  Therefore, they are
not affected by "credit" problems or changes in the VLArb table (which
may shut down VL0).

Non-enabled VFs may only create UD proxy QP0 qps (which are forced by
the hypervisor to send packets using the q-key it assigns and places
in the qp-context).  Thus, non-enabled VFs will not pose a security
risk.  The hypervisor discards any privileged MADs it receives from
these non-enabled VFs.

By default, all VFs are NOT enabled, and must explicitly be enabled
by the administrator.

The sysfs interface which operates the VF enablement infrastructure
is provided in the next commit.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Add the infrastructure needed to support ndo_get_phys_port_id which
allows users to identify to which physical port a net-device is connected
to by reading a unique port id.
This will work for VFs and PFs.
The driver uses a new device capability - phys_port_id, The PF driver
reads the port phys_port_id from Firmware and stores it. The VF driver
reads the port phys_port_id from the PF using QUERY_FUNC_CAP command.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set nic_info field in QUERY_FUNC_CAP, which designates
supplementary NIC information is provided by the hypervisor.
When set, the following fields are valid: nic_num_rings,
nic_indirection_tbl_sz, cur_mac and phys_port_id.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds new firmware command and new firmware event.  The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.

Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read HCA frequency, read PCI clock bar and offset, map internal clock to
PCI bar.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add memory windows-related code to INIT_HCA and QUERY_HCA.
Signed-off-by: NHaggai Eran <haggaie@mellanox.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The Firmware dynamically changes flow steering hash configuration from covering
L2 only to "full" L2/L3/L4 mode needed.  The dynamic change allows the driver
to set hard coded hash configuration which is changed by the firmware from L2
to L2/L3/L4 when attaching the first L3/L4 flow steering rule and back to L2
when there are no more such rules.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate flow steering capability detection from the decision to activate.

For the master (and for native), detect the flow steering capability
in mlx4_dev_cap, but activate the appropriate steering type in a new
function choose_flow_steering() based on detected data.

For VFs, activate flow steering based on what was actually activated
by the master, where that info is obtained via QUERY_HCA. This fixes
the current VF detection which is wrongly based on QUERY_DEV_CAP.

Also, for SR-IOV mode, if flow steering may be activated, do so only
if the max number of QPs per rule is sufficient to satisfy one
subscription per VF.  If not, fall back to B0 mode. This is needed to
serve registrations done by L2 network drivers such as mlx4_en and
IPoIB when the network stack attempts to join to multicast groups such
as all-hosts or the IPoIB broadcast group.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

ConnectX-3 devices can use either 64- or 32-byte completion queue
entries (CQEs) and event queue entries (EQEs).  Using 64-byte
EQEs/CQEs performs better because each entry is aligned to a complete
cacheline.  This patch queries the HCA's capabilities, and if it
supports 64-byte CQEs and EQES the driver will configure the HW to
work in 64-byte mode.

The 32-byte vs 64-byte mode is global per HCA and not per CQ or EQ.

Since this mode is global, userspace (libmlx4) must be updated to work
with the configured CQE size, and guests using SR-IOV virtual
functions need to know both EQE and CQE size.

In case one of the 64-byte CQE/EQE capabilities is activated, the
patch makes sure that older guest drivers that use the QUERY_DEV_FUNC
command (e.g as done in mlx4_core of Linux 3.3..3.6) will notice that
they need an update to be able to work with the PPF. This is done by
changing the returned pf_context_behaviour not to be zero any more. In
case none of these capabilities is activated that value remains zero
and older guest drivers can run OK.

The SRIOV related flow is as follows

1. the PPF does the detection of the new capabilities using
   QUERY_DEV_CAP command.

2. the PPF activates the new capabilities using INIT_HCA.

3. the VF detects if the PPF activated the capabilities using
   QUERY_HCA, and if this is the case activates them for itself too.

Note that the VF detects that it must be aware to the new PF behaviour
using QUERY_FUNC_CAP.  Steps 1 and 2 apply also for native mode.

User space notification is done through a new field introduced in
struct mlx4_ib_ucontext which holds device capabilities for which user
space must take action. This changes the binary interface so the ABI
towards libmlx4 exposed through uverbs is bumped from 3 to 4 but only
when **needed** i.e. only when the driver does use 64-byte CQEs or
future device capabilities which must be in sync by user space. This
practice allows to work with unmodified libmlx4 on older devices (e.g
A0, B0) which don't support 64-byte CQEs.

In order to keep existing systems functional when they update to a
newer kernel that contains these changes in VF and userspace ABI, a
module parameter enable_64b_cqe_eqe must be set to enable 64-byte
mode; the default is currently false.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Previously, the structure of a guest's proxy QPs followed the
structure of the PPF special qps (qp0 port 1, qp0 port 2, qp1 port 1,
qp1 port 2, ...).  The guest then did offset calculations on the
sqp_base qp number that the PPF passed to it in QUERY_FUNC_CAP().

This is now changed so that the guest does no offset calculations
regarding proxy or tunnel QPs to use.  This change frees the PPF from
needing to adhere to a specific order in allocating proxy and tunnel
QPs.

Now QUERY_FUNC_CAP provides each port individually with its proxy
qp0, proxy qp1, tunnel qp0, and tunnel qp1 QP numbers, and these are
used directly where required (with no offset calculations).

To accomplish this change, several fields were added to the phys_caps
structure for use by the PPF and by non-SR-IOV mode:

    base_sqpn -- in non-sriov mode, this was formerly sqp_start.
    base_proxy_sqpn -- the first physical proxy qp number -- used by PPF
    base_tunnel_sqpn -- the first physical tunnel qp number -- used by PPF.

The current code in the PPF still adheres to the previous layout of
sqps, proxy-sqps and tunnel-sqps.  However, the PPF can change this
layout without affecting VF or (paravirtualized) PF code.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

In addition, pass the proxy and tunnel QP numbers to slaves so the
driver can perform special QP paravirtualization.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The driver is modified to support three operation modes.

If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.

When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.

When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.

Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a 64-bit flags2 features member to struct mlx4_dev to
export further features of the hardware.  The original flags field
tracks features whose support bits are advertised by the firmware in
offsets 0x40 and 0x44 of the query device capabilities command.
flags2 will track features whose support bits are scattered at various
offsets.

RSS support is the first feature to be exported through flags2.  RSS
capabilities are located at offset 0x2e.  The size of the RSS
indirection table is also given in this offset.
Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The Virtual Functions should not be aware their function number.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.

2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
   IB or Ethernet.
   The driver will use this hint in case the user didn't specify explicitly the link layer
   type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
   and default the port to link sensing
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Added module parameters sr_iov and probe_vf for controlling enablement of
   SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
   SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
   ports configured as desired.
   In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
   for the case where the FW supports both port types (ETH and IB), the
   port_type_array parameter is used.
   By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
   to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
   mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
   modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
   VFs obtain their startup information from the PF (master) device via the
   comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
   aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership:  Currently, only one PF is supported by the driver.
   If the HCA is burned with FW which enables more than one PF, only one
   of the PFs is allowed to run.  The first one up grabs a FW ownership
   semaphone -- all other PFs will find that semaphore taken, and the
   driver will not allow them to run.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NLiran Liss <liranl@mellanox.co.il>
Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following commands are added here:
1. QUERY_FUNC_CAP and its wrapper.  This function is used by VFs when
   they start up to receive configuration information from the PF, such
   as resource quotas for this VF, which ports should be used (currently
   two), what protocol is running on the port (currently Ethernet ONLY,
   or port not active).

2. QUERY_PORT and its wrapper. Previously, this FW command was invoked directly
   by the ETH driver (en_port.c) using mlx4_cmd_box. Virtualization is now
   required here (the VF's MAC address must be substituted for the PFs
   MAC address returned by the FW). We changed the invocation
   in the ETH driver to use mlx4_QUERY_PORT, and added the wrapper.

3. QUERY_HCA. Used by the VF to determine how the HCA was initialized.
   For now, we need only the multicast table member entry size
   (log2_mc_table_entry_sz, in the ConnectX PRM).  No wrapper is needed
   here, because the data may be passed as is to the VF without modification).

   In this command, we have added a GLOBAL_CAPS field for passing required
   configuration information from FW to a VF (this field is to allow safely
                   adding new SRIOV capabilities which require support in VF drivers, too).
   Bits will set here by FW in response to PF-driver configuration commands which
   will activate as yet undefined new SRIOV features. The VF will test to see that
   all required capabilities indicated by this field are supported (i.e., if a bit
   is set and the VF driver does not recognize that bit, it must abort
   its initialization).  Currently, no bits are set.

4. Added a CLOSE_PORT wrapper.  The PF context needs to keep track of how many VF contexts
   have the port open.  The PF context will not actually issue the FW close port command
   until the last port user issues a CLOSE_PORT request.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.

CC: Roland Dreier <roland@kernel.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ConnectX devices support a set of flow counters that can be attached
to a set containing one or more QPs.  Each such counter tracks receive
and transmit packets and bytes of these QPs.  This patch queries the
device to check support for counters, handles initialization of the
HCA to enable counters, and initializes a bitmap allocator to control
counter allocations.  Derived from patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Query another dword containing up to 32 extended device capabilities
and merge it into struct mlx4_caps.flags.  Update the code that
handles the current extended device capabilities (e.g UDP RSS, WoL,
vep steering, etc) to use the extended device cap flags field instead
of a field per extended capability.  Initial patch done by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The latest firmware adds a second dword containing more device flags,
so extend the device capabilities flags field from 32 to 64 bits.
Derived from patch by Eli Cohen <eli@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver queries the FW for WOL support.
Ethtool get/set_wol is implemented accordingly.
Only magic packets are supported at the time.
Signed-off-by: NIgor Yarovinsky <igory@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding capability for RSS for UDP traffic, hashing is done based on
IP addresses and UDP port number.
The support depends on HW/FW capabilities.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The report now based on query from FW, giving the correct tranciever type
and link speed.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
   on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Multi-protocol adapters support different port types.  Each consumer
of mlx4_core queries for supported port types; in particular mlx4_ib
can no longer assume that all physical ports belong to it.  Port type
is configured through a sysfs interface.  When the type of a port is
changed, all mlx4 interfaces are unregistered, and then registered
again with the new port types.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Get maximum ethernet MTU and default MAC address from the firmware
QUERY_DEV_CAP command.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

For ethernet support, we need to reserve QPs for the ethernet and
fibre channel driver.  The QPs are reserved at the end of the QP
table.  (This way we assure that they are aligned to their size)

We need to consider these reserved ranges in bitmap creation, so we
extend the mlx4 bitmap utility functions to allow reserved ranges at
both the bottom and the top of the range.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update existing Mellanox copyright lines to 2008, and add such lines
to files where they are missing.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for the following operations to mlx4 when device firmware
supports them:

 - Send with invalidate and local invalidate send queue work requests;
 - Allocate/free fast register MRs;
 - Allocate/free fast register MR page lists;
 - Fast register MR send queue work requests;
 - Local DMA L_Key.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There was a bug in some versions of the mlx4 driver in
mlx4_alloc_fmr(), which hardcoded the minimum acceptable page_shift to
be 12.  However, new ConnectX firmware can support a minimum
page_shift of 9 (log_pg_sz of 9 returned by QUERY_DEV_LIM) -- so with
old drivers, ib_fmr_alloc() would fail for ULPs using the device
minimum when creating FMRs.

To preserve firmware compatibility with released mlx4 drivers, the
firmware will continue to return 12 as before for log_page_sz in
QUERY_DEV_CAP for these drivers.  However, to enable new drivers to
take advantage of the available smaller page size, the mlx4 driver now
first sets the log_pg_sz to the device minimum by setting a
log_page_sz value to 0 via the MOD_STAT_CFG command and then reading
the real minimum via QUERY_DEV_CAP.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add TSO support to the mlx4_ib driver.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The firmware QUERY_ADAPTER command does not return vendor_id,
device_id, and revision_id; eliminate these fields from the query.

Initialize the rev_id field of the mlx4 device via init_node_data (MAD
IFC query), as is done in the query_device verb implementation.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Get the maximum message size from the device capabilities returned
from the QUERY_DEV_CAP firmware command, rather than hard-coding 2 GB.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set.  Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>