During suspend the bus state is put in the down state. When data
is being transmitted during this state then the netdev queue will
be close. This patch will wake the queue on state data if the
queue was closed.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Each bus driver is maintaing an exported bus state indicating
if upper layers can or cannot send data. SDIO is using this state
also for more private states. This makes handling the states and
state changes complex. This patch minimises the exposed states
and makes SDIO keep track of an internal state where necessary.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Before going in suspend state the watchdog thread needs to put the
device in bus sleep state, which assures it can go in deep-sleep
state during D3 state.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The driver always called cfg80211_disconnected() with reason parameter
set to zero, ie. unknown. However, firmware does provide a valid
802.11 reason code in DEAUTH and DISASSOC event message to the driver.
This patch passes the reason code to cfg80211_disconnected().
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Control frames are normally handled outside DPC, but sometimes
within DPC. To simplify code always handle control within DPC.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When the system is resumed a deadlock can occur when DPC gets
entered before resume is complete. This patch fixes this by
properly checking the suspend state outside the claim_host code
block.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On every tx the flow worker is triggered. When running high
throughput data this causes an excessive amount of times the worker
gets activated. This patch starts scheduling the worker more relaxed
once outstanding tx has reached a certain depth.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This fixes issue reported by Dan Carpenter:
The patch 3277213f: "wil6210: ADDBA/DELBA flows" from Dec 23,
2014, leads to the following static checker warning:

        drivers/net/wireless/ath/wil6210/rx_reorder.c:205 wil_tid_ampdu_rx_alloc()
        error: scheduling with locks held: 'spin_lock:tid_rx_lock'

drivers/net/wireless/ath/wil6210/rx_reorder.c
   202  struct wil_tid_ampdu_rx *wil_tid_ampdu_rx_alloc(struct wil6210_priv *wil,
   203                                                  int size, u16 ssn)
   204  {
   205          struct wil_tid_ampdu_rx *r = kzalloc(sizeof(*r), GFP_KERNEL);
                                                                 ^^^^^^^^^^
   206
   207          if (!r)
   208                  return NULL;
   209
   210          r->reorder_buf =
   211                  kcalloc(size, sizeof(struct sk_buff *), GFP_KERNEL);
                                                                ^^^^^^^^^^^
   212          r->reorder_time =
   213                  kcalloc(size, sizeof(unsigned long), GFP_KERNEL);
                                                             ^^^^^^^^^^^
   214          if (!r->reorder_buf || !r->reorder_time) {
   215                  kfree(r->reorder_buf);
   216                  kfree(r->reorder_time);
   217                  kfree(r);
   218                  return NULL;
   219          }
   220

[ snip ]

   331          spin_lock_bh(&sta->tid_rx_lock);
                ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
spin lock held.

   332
   333          wil_tid_ampdu_rx_free(wil, sta->tid_rx[tid]);
   334          sta->tid_rx[tid] = wil_tid_ampdu_rx_alloc(wil, agg_wsize, ssn);
                                   ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
function called with the lock held.

   335
   336          spin_unlock_bh(&sta->tid_rx_lock);
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Access point require this API to check peer alive status.
Assume peer is alive when it is connected, because
firmware implements keep alive checks and will disconnect
peer if it is not alive.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement Tx status reporting using skb_complete_wifi_ack().
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Interrupt moderation parameters will never be passed as module
parameters. For product, they will be hard-coded after lab testing,
and for debugging, they can be altered via debugfs.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Due to HW limitation, inter-packet gap timeout max value is 13 usec.
Update of current thresholds from 15 to 13 usec.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Tuning rings size for performance optimization.
Increasing Tx ring size, allows buffering more packets for HW, thus
eliminating idle periods which were observed with smaller ring at
high throughput, because HW was fetching packets faster than driver was
filling them into the TX ring. Rx ring was similarly increased to
avoid same problems in Rx.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Tx queue was hard-coded to 1000 in ether_setup. Add wil_dev_setup
function which configures tx queue len to chosen default value
after calling ether_setup.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

upon cfg80211_stop_ap, a graceful AP shutdown is requested from firmware
followed by firmware reset.
In case graceful request failed, error was returned to cfg80211.

The change is to return success in this scenario, because firmware
reset will anyhow shutdown the AP.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

netif_carrier_on indication was too late. In case Rx packet received
before netif_carrier_on indication, upper layers could not send
Tx packet back.

The fix is to indicate netif_carrier_on earlier:
for STA, indicate netif_carrier_on when association starts.
for AP/PCP, indicate netif_carrier_on upon starting AP/PCP.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Incorporate changes from firmware.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

After rtl8192cu download firmware routine, set fw_ready flag.
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some devices do not support extended scan.
This patch adds support to enble ext_scan selectively.
For SD/PCIe interfaces, deefine ext_scan_support as part of
card structure and use it to initialize ext_scan in adapter
during registering device. For USB interfaces, we initialize
ext_scan during register_dev handler.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

USB8801 is Marvell's 1x1 802.11bgn offering.
Patch adds Device IDs support and defines TX buffer size.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SD8801 is Marvell's 1x1 802.11bgn offering.
This patch adds Device IDs for SD8801 and also defines card
structure which has definition for register offsets, buffer sizes etc.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Reviewed-by: NJames Cameron <quozl@laptop.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ath9k and ath9k_htc use the variable name "led_blink" to indicate
whether the module parameter "blink" is on. This name is easy to
conflict with other variables, and has caused a compiler error found
by kbuild test bot. The compiler error is as following:

drivers/net/wireless/ath/ath9k/ath9k_htc.o:(.data+0x47c): multiple definition of `led_blink'
drivers/net/wireless/ath/ath9k/ath9k.o:(.bss+0x20): first defined here

Fixes: 3a939a67 ("ath9k_htc: Add a module parameter to disable blink")
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NHong Xu <hong@topbug.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Patch "rtlwifi: add support to send beacon frame" allows
the beaconing of rtl8192cu. But mesh beaconing is not
working. Fix this.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In AP mode, beacon frame is necessary to keep connection.
this patch adds a sending beacon frame routine in initialization routine.
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds fix to set carrier state off during ndo_open.
Carrier should be set to ON when device is ready to send data.
In case of station/adhoc interface device is able to transfer
data after successful association/join operation.
For AP this would be after bss_active event.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Starting with kernel 3.19-rc1 early registration of bcma on MIPS is done
a bit later, with memory allocator available. This allows us to simplify
code by using standard bus scanning method.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The kernel's string library does in fact have strcasecmp, at least
since ded220bd ("[STRING]: Move strcasecmp/strncasecmp to
lib/string.c"). Moreover, this open-coded version is in fact wrong: If
the strings only differ in their last character, a and b have already
been incremented to point to the terminating NUL bytes, so they would
wrongly be treated as equal.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

if(!wait_for_completion_interruptible_timeout(...))
only handles the timeout case - this patch adds handling the
signal case the same as timeout.
Signed-off-by: NNicholas Mc Guire <der.herr@hofr.at>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

if(!wait_for_completion_interruptible_timeout(...))
only handles the timeout case - this patch adds handling the
signal case the same as timeout.
Signed-off-by: NNicholas Mc Guire <der.herr@hofr.at>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Coverity: CID 114932
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This clause is conditioned on htc_hdr != NULL, but it will only be NULL
when that check is reached.

Coverity: CID 114318
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch introduces the use of function put_unaligned_le32.

This is done using Coccinelle and semantic patch used is as follows:

@a@
typedef u32, __le32, uint32_t;
{u32,__le32,uint32_t} e32;
identifier tmp;
expression ptr;
expression y,e;
type T;
type T;
@@

- tmp = cpu_to_le32(y);

<+... when != tmp
(
- memcpy(ptr, (T)&tmp, \(4\|sizeof(u32)\|sizeof(__le32)\|sizeof(uint32_t)\|sizeof(e32)\));
+ put_unaligned_le32(y,ptr);
|
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_le32(y,ptr);
)
...+>
? tmp = e

@@ type T; identifier a.tmp; @@

- T tmp;
...when != tmp
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This moves main bus init code to the main.c and renames old function to
make its purpose clear.
Thanks to this change we'll also be able to separate scanning from
registration (and support PCIe Gen 2 devices) in the future.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Call b43_leds_stop during suspend to avoid this WARN:

WARNING: CPU: 1 PID: 0 at net/mac80211/util.c:755 ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]()
queueing ieee80211 work while going to suspend

 [...]

Call Trace:
 [<c165fb2a>] dump_stack+0x48/0x69
 [<c1052f7b>] warn_slowpath_common+0x8b/0xc0
 [<f9c30225>] ? ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]
 [<f9c30225>] ? ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]
 [<c1052fe3>] warn_slowpath_fmt+0x33/0x40
 [<f9c30225>] ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]
 [<f9c30260>] ieee80211_queue_work+0x20/0x40 [mac80211]
 [<f9f25d78>] b43_led_brightness_set+0x28/0x30 [b43]
 [<c14f3835>] led_timer_function+0xd5/0xe0
 [<c10cb534>] call_timer_fn+0xa4/0x4a0
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We recently introduced a new error path which needs an unlock.

Fixes: 6d5a748d ('wlcore: add ability to reduce FW interrupts during suspend')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The else if check condition checks for the opposite of the
if check, hence the else if check is redundant and can be
replaced with a simple else:

if (rtlpriv->rtlhal.macphymode == SINGLEMAC_SINGLEPHY) {
	..
} else if (rtlpriv->rtlhal.macphymode != SINGLEMAC_SINGLEPHY) {
	..
}

replaced with:

if (rtlpriv->rtlhal.macphymode == SINGLEMAC_SINGLEPHY) {
	..
} else {
	..
}
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add an option "blink" to enable or disable the LED blink. The default
value is set to 1 so that existing users would not experience any
unexpected changes.
Signed-off-by: NHong Xu <hong@topbug.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently, wcn36xx only asks for a TX BA session if it has
already established one for RX.  Thus, two wcn36xx devices cannot
do a-mpdu between themselves since they both wait for the other
to go first.  Fix this by starting a BA session after a few QoS
data frames have been sent to a STA.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The pdu is part of the buffer descriptor, so it makes
sense that one function would fill both.  Also, passing
the whole skb instead of just the header pointer to the
set_tx_data function paves the way for using its fields
for ampdu setup inside set_tx_data().
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The dxe lock is missing its initialization, so add it.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>