This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.

This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures.  Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch creates platform_device entries for the Marvell mv64x60
MPSC (multi-protocol serial controller) ports, based on information
contained in the device tree.

This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures.  Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There are 3 interrupt groups each with its own status/mask registers.
We use a separate struct irq_chip for each interrupt group and handle
interrupts in two stages or levels: level 1 selects the appropriate
struct irq_chip, and level 2 selects individual interrupts within
that irq_chip.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Some platforms support a variety processor modules with no method of
determining which exact processor module is being used except by
examining Vital Product Data (VPD).  The modules may have different
amounts of memory, clock frequencies, etc. so reading the VPD becomes
necessary to correctly set properties in the device tree before its
passed to the kernel.

Often the VPD is stored in I2C EEPROMs so an I2C driver becomes necessary.
This I2C driver is for the I2C controller that's embedded on the Marvel
mv64x60 line of host bridges.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The bootwrapper requires a serial driver to allow cmdline editing
and information reporting on the console.  This driver is required
by platforms that boot a zImage and use the MPSC for the console.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The mv64x60 host bridge has many windows between its various components
(cpu, system memory, ethernet ctlr, MPSC, DMA ctlr, PCI MEM, PCI I/O).
Unfortunately, the firmware on some of mv64x60-based platforms do not
properly or completely configure those windows (e.g., MPSC->system memory
windows not configured or CPU->PCI MEM space not configured).

So, the missing configuration needs to be done in either the bootwrapper
or in the kernel.  To keep the kernel as clean as possible, it is done
in the bootwrapper.  Note that I/O controller configuration is NOT being
done, its only the windows to allow the I/O controllers and other components
to access memory, etc. that is being done--drivers assume that their
controllers can already access system memory).

Table of routines and the windows they configure:
	mv64x60_config_ctlr_windows()	ENET->System Memory
					MPSC->System Memory
					IDMA->System Memory

	mv64x60_config_pci_windows()	PCI MEM->System Memory
					PCI I/O->Bridge's Registers

	mv64x60_config_cpu2pci_window()	CPU->PCI MEM
					CPU->PCI I/O
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add 'zImage.dts' and 'zImage.dts_initrd' build rules that automatically
compile and wrap a dts file from arch/powerpc/boot/dts into the zImage file.
The resulting zImage will be arch/powerpc/boot/zImage.dts.<platform> and
arch/powerpc/boot/zImage.dts_initrd.<platform>, respectively.

Having separate rules allows the user to choose whether to include a device
tree--and which device tree--at build time.  This is useful when one Makefile
target builds a zImage that runs on several platforms except for differing
device trees.  By just setting CONFIG_DEVICE_TREE and running "make zImage.dts"
the exact zImage you want is built without Makefile bloat or manually running
the wrapper script.

The dts file is expected to be arch/powerpc/boot/dts/$(CONFIG_DEVICE_TREE)
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Spelling fixes in arch/ppc/.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The boot wrapper platform init code on 83xx and 85xx using the cuboot
platform type was incorrectly assuming that u-boot supplied the size
of the initrd, whereas it actually supplies the end address.  This
fixes it.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Update ps3_defconfig.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fix compiler warning:

ps3/smp.c:122: warning: ignoring return value of 'request_irq'
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

An mdio bus scan was added with ucc_geth phylib
migration patches, now machines complain on boot, saying:

prom_parse: Bad cell count for /qe@e0100000/mdio@2120/ethernet-phy@00
prom_parse: Bad cell count for /qe@e0100000/mdio@2120/ethernet-phy@01

since size-cells can indeed be 0, this patch fixes the check.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Greatly simplify the function smp_space_timers.

The stolen time calculation (per comment within the code) doesn't need the
half-jiffy stagger any more.  There isn't an issue with bouncing off global
locks, so we really shouldn't need any sort of staggering at all.

However, the last_jiffy value still needs to be set.   This removes the
extra stagger logic, and just sets the values.

This change should benefit applications that rely on barrier
synchronization, and will help cut down OS jitter.

Boot tested across the board (G5,power3,power4,power5,970mp blade).
Signed-off-by: NWill Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fixes warnings:

arch/powerpc/platforms/ps3/system-bus.c: In function 'ps3_map_sg':
arch/powerpc/platforms/ps3/system-bus.c:278: warning: unused variable 'i'
arch/powerpc/platforms/ps3/system-bus.c:277: warning: unused variable 'dev'
arch/powerpc/platforms/ps3/setup.c:103: warning: 'prealloc' defined but not used
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

fixes:
arch/powerpc/platforms/pasemi/idle.c: In function 'pasemi_system_reset_exception':
arch/powerpc/platforms/pasemi/idle.c:55: warning: implicit declaration of function 'do_IRQ'
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This case will never be hit, but it should be corrected anyway.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (122 commits)
  [ALSA] version 1.0.14rc4
  [ALSA] Add speaker pin sequencing to hda_codec.c:snd_hda_parse_pin_def_config()
  [ALSA] hda-codec - Add ALC861VD Lenovo support
  [ALSA] hda-codec - Fix connection list in generic parser
  [ALSA] usb-audio: work around wrong wMaxPacketSize on ESI M4U
  [ALSA] usb-audio: work around broken M-Audio MidiSport Uno firmware
  [ALSA] usb-audio: explicitly match Logitech QuickCam
  [ALSA] hda-codec - Fix a typo
  [ALSA] hda-codec - Fix ALC880 uniwill auto-mutes
  [ALSA] hda-codec - Fix AD1988 SPDIF playback route control
  [ALSA] wm8750 typo fix
  [ALSA] wavefront: only declare isapnp on CONFIG_PNP
  [ALSA] hda-codec - bug fixes for stac92xx HDA codecs.
  [ALSA] add MODULE_FIRMWARE entries
  [ALSA] do not depend on FW_LOADER when internal firmware images are used
  [ALSA] hda-codec - Fix resume of STAC92xx codecs
  [ALSA] usbaudio - Revert the minimal period size fix patch
  [ALSA] hda-codec - Add support for new HP DV series laptops
  [ALSA] usb-audio - Fix the minimum period size per transfer mode
  [ALSA] sound/pcmcia/vx/vxpocket.c: fix an if() condition
  ...

* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (44 commits)
  V4L/DVB (5571): V4l1-compat:  Make VIDIOCSPICT return errors in a useful way
  V4L/DVB (5624): Radio-maestro.c cleanup
  V4L/DVB (5623): Dsbr100.c Replace usb_dsbr100_do_ioctl to use video_ioctl2
  V4L/DVB (5622): Radio-zoltrix.c cleanup
  V4L/DVB (5621): Radio-cadet.c Replace cadet_do_ioctl to use video_ioctl2
  V4L/DVB (5619): Dvb-usb: fix typo
  V4L/DVB (5618): Cx88: Drop the generic i2c client from cx88-vp3054-i2c
  V4L/DVB (5617): V4L2: videodev, allow debugging
  V4L/DVB (5614): M920x: Disable second adapter on LifeView TV Walker Twin
  V4L/DVB (5613): M920x: loosen up 80-col limit
  V4L/DVB (5612): M920x: rename function prefixes from m9206_foo to m920x_foo
  V4L/DVB (5611): M920x: replace deb_rc with deb
  V4L/DVB (5610): M920x: remove duplicated code
  V4L/DVB (5609): M920x: group like functions together
  V4L/DVB (5608): M920x: various whitespace cleanups
  V4L/DVB (5607): M920x: Initial support for devices likely manufactured by Dposh
  V4L/DVB (5606): M920x: add "c-basic-offset: 8" to help emacs to enforce tabbing
  V4L/DVB (5605): M920x: Add support for LifeView TV Walker Twin
  V4L/DVB (5603): V4L: Prevent queueing queued buffers.
  V4L/DVB (5602): Enable DiSEqC in Starbox II (vp7021a)
  ...

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Quicklist support for IA64
  [IA64] fix Kprobes reentrancy
  [IA64] SN: validate smp_affinity mask on intr redirect
  [IA64] drivers/char/snsc_event.c:206: warning: unused variable `p'
  [IA64] mca.c:121: warning: 'cpe_poll_timer' defined but not used
  [IA64] Fix - Section mismatch: reference to .init.data:mvec_name
  [IA64] more warning cleanups
  [IA64] Wire up epoll_pwait and utimensat
  [IA64] Fix warnings resulting from type-checking in dev_dbg()
  [IA64] typo s/kenrel/kernel/

The code was ok, but triggered warnings for calling __init from
__cpuinit. Instead call it from check_bugs instead.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I'm using a custom BIOS to configure the northbridge GART at address
0x80000000, size 2G.  Linux complains:

"Aperture from northbridge cpu 0 beyond 4GB. Ignoring."

I think there's an off-by-two error in arch/x86_64/kernel/aperture.c:

AK: use correct types for i386
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
  further UTF-8 fixes and name correction
  Fix wrong identifier name in Documentation/kref.txt

> -** Copyright 1994 by Bj<94>rn Brauel
> +** Copyright 1994 by Bj”rn Brauel

I think these were cp437, and it should read 'Björn'.
(asm-m68k/atari*.h)

Also note that Arnaldo just put more legacy noise into CREDITS...
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

There's a typo / wrong identifier name in Documentation/kref.txt. Fix it.
Signed-off-by: NSatyam Sharma <ssatyam@cse.iitk.ac.in>
Acked-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-ip22:
  Convert SGI IP22 and specific drivers to platform_device.

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (28 commits)
  [MIPS] Rework cobalt_board_id
  [MIPS] Use RTC_CMOS for Cobalt
  [MIPS] Use platform_device for Cobalt UART
  [MIPS] Separate Alchemy processor based boards config
  [MIPS] Fix build error in atomic64_cmpxchg
  [MIPS] Run checksyscalls for N32 and O32 ABI
  [MIPS] tlbex: use __maybe_unused
  [MIPS] excite: use __maybe_unused
  [MIPS] Add extern cobalt_board_id
  [MIPS] Remove unused CONFIG_TOSHIBA_BOARDS
  [MIPS] Rename tb0229_defconfig to tb0219_defconfig
  [MIPS] Update tb0229_defconfig; add CONFIG_GPIO_TB0219.
  [MIPS] Add minimum defconfig for RBHMA4200
  [MIPS] SB1: Build fix.
  [MIPS] Drop __devinit tag from allocate_irqno() and free_irqno()
  [MIPS] clocksource: use CLOCKSOURCE_MASK() macro
  [MIPS] Remove LIMITED_DMA support
  [MIPS] Remove Momenco Jaguar ATX support
  [MIPS] Remove Momenco Ocelot G support
  [MIPS] FPU hazard handling
  ...

* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
  Fix compile/link of init/do_mounts.c with !CONFIG_BLOCK
  When stacked block devices are in-use (e.g. md or dm), the recursive calls

* 'audit.b38' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  [PATCH] Abnormal End of Processes
  [PATCH] match audit name data
  [PATCH] complete message queue auditing
  [PATCH] audit inode for all xattr syscalls
  [PATCH] initialize name osid
  [PATCH] audit signal recipients
  [PATCH] add SIGNAL syscall class (v3)
  [PATCH] auditing ptrace

* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
  USB HID: hiddev - fix race between hiddev_send_event() and hiddev_release()
  HID: add hooks for getkeycode() and setkeycode() methods
  HID: switch to using input_dev->dev.parent
  USB HID: Logitech wheel 0x046d/0xc294 needs HID_QUIRK_NOGET quirk
  USB HID: usb_buffer_free() cleanup
  USB HID: report descriptor of Cypress USB barcode readers needs fixup
  Bluetooth HID: HIDP - don't initialize force feedback
  USB HID: update CONFIG_USB_HIDINPUT_POWERBOOK description
  HID: add input mappings for non-working keys on Logitech S510 remote

IA64 is the origin of the quicklist implementation.  So cut out the pieces
that are now in core code and modify the functions called.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

In case of reentrance i.e when a probe handler calls a functions which
inturn has a probe, we save a previous kprobe information and just single
step the reentrant probe without calling the actual probe handler.  During
this reentracy period, if an interrupt occurs and if probe happens to
trigger in the inturrupt path, then we were corrupting the previous kprobe(
as we were overriding the previous kprobe info) info their by crashing the
system.  This patch fixes this issues by having a an array of previous
kprobe info struct(with the array size of 2).

This similar technique is not needed on i386 and x86_64 because by default
interrupts are turn off in the break/int3 exception handler.
Signed-off-by: NAnil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

On SN, only allow one bit to be set in the smp_affinty mask when
redirecting an interrupt.  Currently setting multiple bits is allowed, but
only the first bit is used in determining the CPU to redirect to.  This has
caused confusion among some customers.

[akpm@linux-foundation.org: fixes]
Signed-off-by: NJohn Keller <jpk@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
  [NETFILTER]: xt_conntrack: add compat support
  [NETFILTER]: iptable_raw: ignore short packets sent by SOCK_RAW sockets
  [NETFILTER]: iptable_{filter,mangle}: more descriptive "happy cracking" message
  [NETFILTER]: nf_nat: Clears helper private area when NATing
  [NETFILTER]: ctnetlink: clear helper area and handle unchanged helper
  [NETFILTER]: nf_conntrack: Removes unused destroy operation of l3proto
  [NETFILTER]: nf_conntrack: Removes duplicated declarations
  [NETFILTER]: nf_nat: remove unused argument of function allocating binding
  [NETFILTER]: Clean up table initialization
  [NET_SCHED]: Avoid requeue warning on dev_deactivate
  [NET_SCHED]: Reread dev->qdisc for NETDEV_TX_OK
  [NET_SCHED]: Rationalise return value of qdisc_restart
  [NET]: Fix dev->qdisc race for NETDEV_TX_LOCKED case
  [UDP]: Fix AF-specific references in AF-agnostic code.
  [IrDA]: KingSun/DonShine USB IrDA dongle support.
  [IPV6] ROUTE: Assign rt6i_idev for ip6_{prohibit,blk_hole}_entry.
  [IPV6]: Do no rely on skb->dst before it is assigned.
  [IPV6]: Send ICMPv6 error on scope violations.
  [SCTP]: Do not include ABORT chunk header in the notification.
  [SCTP]: Correctly copy addresses in sctp_copy_laddrs
  ...

When exporting input device bitmaps via compat_ioctl on BIG_ENDIAN
platforms evdev calculates data size incorrectly. This causes buffer
overflow if user specifies buffer smaller than maxlen.
Signed-off-by: NKenichi Nagai <kenichi3.nagai@toshiba.co.jp>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

During a 'resync' or similar activity, md checks if the devices in the
array are otherwise active and winds back resync activity when they are.
This test in done in is_mddev_idle, and it is somewhat fragile - it
sometimes thinks there is non-sync io when there isn't.

The test compares the total sectors of io (disk_stat_read) with the sectors
of resync io (disk->sync_io).  This has problems because total sectors gets
updated when a request completes, while resync io gets updated when the
request is submitted.  The time difference can cause large differenced
between the two which do not actually imply non-resync activity.  The test
currently allows for some fuzz (+/- 4096) but there are some cases when it
is not enough.

The test currently looks for any (non-fuzz) difference, either positive or
negative.  This clearly is not needed.  Any non-sync activity will cause
the total sectors to grow faster than the sync_io count (never slower) so
we only need to look for a positive differences.

If we do this then the amount of in-flight sync io will never cause the
appearance of non-sync IO.  Once enough non-sync IO to worry about starts
happening, resync will be slowed down and the measurements will thus be
more precise (as there is less in-flight) and control of resync will still
be suitably responsive.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the obsolete "if [ ]" construct from the video console Kconfig
file.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Acked-by: NJames Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert internal wait_pm2() function to fb API fb_sync() method.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>