This patch adds new mac802154 hw flags for transmit power, csma and
listen before transmit (lbt). These flags indicates that the transceiver
supports these features. If the flags are set and the driver doesn't
implement the necessary functions, then ieee802154_register_device
returns -ENOSYS "Function not implemented".

This patch merges also all at86rf230 operations into one operations structure
and set the right hw flags for the at86rf230 transceivers.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fec_enet_alloc_buffers() assumes that kmalloc() will never fail, which
is an invalid assumption.  Fix this by implementing a common error
cleanup path, and use it to also clean up after failed bounce buffer
allocation.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensure that we do not double-free any allocations, and that any transmit
skbuffs are properly freed when we clean up the rings.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid writing any state until we're certain we can proceed with the
transmission: this avoids writing mapping error address values to the
descriptors, or setting the skbuff pointer until we have successfully
mapped the skb.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate, and then map the receive skb before writing any data to the
ring descriptor or storing the skb.  When freeing the receive ring
entries, unmap and free the skb, and then clear the stored skb pointer.

This means we have ring data and skb pointer in one of two states:
either both fully setup, or nothing setup.

This simplifies the cleanup, as we can use just the skb pointer to
indicate whether the descriptor is setup, and thus avoids potentially
calling dma_unmap_single() on a DMA error value.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls.  At this point, the driver then clears
fep->opened.  The NAPI poll function uses this to stop processing in
the receive path.  Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.

Therefore, this variable serves no purpose, so let's remove it.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the network interface goes down, stop the phy to prevent further
link up status changes before taking the MAC or netif sections down.
This prevents further reception of link up events which could
potentially call fec_restart().

Since phy_stop() takes the mutex which adjust_link() runs under, we
also ensure that adjust_link() will not already be processing a link
up event.

We also need to do this when suspending as well - we don't want a
mis-timed phy state change to restart the MAC after we have stopped
it for suspend, and thus need to restart the phy when resuming.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we disconnect from a phy, we should forget our pointer to it so we
don't accidentally try to configure it.  We handle a NULL phy pointer
correctly in most places, except fec_enet_set_pauseparam().  Fix this
too.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fep->phy_dev can not be NULL here for two reasons:
- fec_enet_open() will have successfully connected the phy, or will have
  failed.
- fec_enet_open() will have called phy_start(fep->phy_dev), which
  unconditionally dereferences this pointer.

If it were to be NULL here, then fec_enet_open() will have already
oopsed.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use netif_stop_queue() in several places where we want to ensure that
the start_xmit function is not running.  netif_stop_queue() is not
sufficient to achieve that - it merely sets a flag to indicate that the
transmit queue(s) should not be run.

netif_tx_disable() gives this guarantee, since it takes the transmit
queue lock while marking the queue stopped.  This will wait for the
transmit function to complete before returning.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While running: while :; do iperf -c <HOST> -P 4; done, transmit timeouts
are regularly reported.  With the tx ring dumping in place, we can see
that all entries are in use, and the hardware has finished transmitting
these packets.  However, the driver has not reclaimed these ring
entries.

This can occur if the interrupt handler is invoked at the wrong moment -
eg:

	CPU0				CPU1
	fec_enet_tx()
					interrupt, IEVENT = FEC_ENET_TXF
					FEC_ENET_TXF cleared
					napi_schedule_prep()
	napi_complete()

The result is that we clear the transmit interrupt, but we don't trigger
any cleaning of the transmit ring.  Instead, use a different strategy:

- When receiving a transmit or receive interrupt, disable both tx and rx
  interrupts, but do not acknowledge them.  Schedule a napi poll.  Don't
  loop.

- When we are polled, read IEVENT, acknowledging the pending transmit
  and receive interrupts, before then going on to process the
  appropriate rings.

This allows us to avoid the race, and has a number of other advantages:
- we cut down on the number of transmit interrupts we have to process.
- we only look at the rings which have pending events.
- we gain additional throughput: the iperf total bandwidth increases
  from about 180Mbps to 240Mbps:

[  3]  0.0-10.0 sec  68.1 MBytes  57.0 Mbits/sec
[  5]  0.0-10.0 sec  72.4 MBytes  60.5 Mbits/sec
[  4]  0.0-10.1 sec  76.1 MBytes  63.5 Mbits/sec
[  6]  0.0-10.1 sec  71.9 MBytes  59.9 Mbits/sec
[SUM]  0.0-10.1 sec   288 MBytes   241 Mbits/sec
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting the pause parameters causes a running network interface to be
restarted.  However, the restart forces the FEC into half-duplex mode,
whether or not the remote end is in half-duplex mode.  Misconfigured
duplex mode is a known source of problems on a link.

Fix this by always preserving the duplex mode on configuration changes.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The iMX6 gigabit FEC does not support half-duplex gigabit operation.
Phys attacked to the FEC may support this, and we currently do nothing
to disable this feature.  This may result in an invalid configuration.
Mask out phy support for gigabit half-duplex operation.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In vxlan and OVS vport-vxlan call common function to get source port
for a UDP tunnel. Removed vxlan_src_port since the functionality is
now in udp_flow_src_port.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support for Wake-on-LAN using Magic Packet with or without SecureOn
password is implemented doing the following:

- setting the password to the relevant UniMAC registers
- flagging the device as a wakeup source for the system, as well as
  its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- enabling the MPD interrupt to wake us

The Device Tree binding documentation is also reflected to specify the
third optional Wake-on-LAN interrupt line.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This boolean tells us whether we are using the RXCHK hardware block,
so use a variable name that reflects that. RXCHK might be used in the
future to implement Wake-on-LAN using ARP or unicast packets.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the hardware recommended suspend/resume procedure for
SYSTEMPORT. We leverage the previous factoring work such that we can
logically break all suspend/resume operations into disctint RX and TX
code paths.

When the system enters S3, we will loose all register contents, so
make sure that we correctly re-program all the hardware and software
views of the RX & TX rings as well.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Factor common code that either enables or disables the network
interface with the networking stack. We are going to reuse these
functions for suspend/resume callbacks.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quite often we need to enable either the transmitter or the receiver
bits in UMAC_CMD, use umac_enable_set() to do that for us.

This is a preliminary change to introduce suspend/resume support in the
driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using internal 10 Mbps PHY, isolate the external PHY from MII bus.
External PHY must be kept powered up because it passes TX from tlan chip to
network.

This fixes weird link-loss problems under load with OC-2326 card at 10 Mbps.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_disable_device() is called in _suspend but there's no corresponding
pci_enable_device() in _resume.
This causes "disabling already-disabled device" warning on 2nd suspend.

Add pci_enable_device() call to _resume to fix this problem.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tlan_reset_adapter, we disable internal PHY when an external one is used.
On cards which use internal PHY in 10 Mbps mode, we enable it later when
setting 10 Mbps mode but it does not really work (PHY fails to reset).
Leave it enabled instead.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a timeout to prevent infinite loop waiting for PHY to reset.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the autonegotiation poll interval from 8 seconds to 2.
This greatly reduces the time needed to detect link presence,
especially on Olicom cards at 10 Mbps (two autonegoatiations required).
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove excess printks when the link is down.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When link is lost on a card which uses internal PHY for 10 Mbit speeds,
restart autonegotiation to allow switching between 10 and 100 Mbps speeds.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Olicom OC-2325 and OC-2326 cards have the MAC address byte-swapped in EEPROM.
Byte-swap the MAC address if it's located at offset 0xF8.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic ethtool support to tlan driver:
 - driver info  - link detect (this allows NetworkManager to detect carrier)
 - EEPROM read
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable old link monitoring code and modify it:
 - control LINK LED
 - use separate timer so it does not interfere with ACT LED

Tested with Olicom OC-2326.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Olicom OC-2325 and OC-2326 ethernet cards have an activity LED but it does not
work with tlan driver as it's not enabled. Enable it.
Tested with OC-2326.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump.

Change-ID: Ie0c36583ffd9997679f46bdf89bc462d3e992995
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement set_settings for ethtool in i40e.

Change-ID: Ie3c3fe18e8ff86c3f25b842844b3d9aabc9bba57
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add i40e implementation of setpauseparam to ethtool.

Change-ID: Ie7766b2091ec8f934737573c9ffd426081966718
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add function set_fc to set the requested FC mode. This patch also
adds the init of FC setting to get_link_info and replaces the init
code to set FC off by default in main. Also adds i40e_set_phy_config
to support this.

Change-ID: I7b25bbaec81f15777137ab324a095f916e44351d
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just move nway reset up, will be used in the next patch.

Change-ID: Ice3b631fa2044debc5c4541b42872a48163f8452
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a new variable, hw.phy.link_info.an_enabled, to track whether autoneg is
enabled.  Also add a new function update_link_info that will update that
variable as well as calling get_link_info to update the rest of the link info.
Also add get_phy_capabilities to support this.

Change-ID: I5157ef03492b6dd8ec5e608ba0cf9b0db9c01710
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Finish the i40e implementation of get_settings for ethtool.

Change-ID: Iec81835aa9380723ae9288bcb79b30a6a1ecd498
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

TPH is not currently enabled in this product, make sure it
isn't enabled by default.

Change-ID: Ibb1a10799c33c4c76dec06fcd53b1d6efa13c1f5
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When turning off ntuple with a FD table full situation,
the driver would have auto disabled FD filter additions.
Clear the auto disable flag for FD_SB so that when the
feature is turned on again using "ethtool -K ethx ntuple on"
we can start adding filters once again.

Change-ID: I036a32e7331bcae765b657c8abb4fa070940b163
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>