Just a few cosmetic fixes to usb_gadget_probe_driver()
and usb_gadget_unregister_driver().

Decreased a few indentation levels with goto statements.

While at that, also add the missing call to musb_stop().
If we don't have OTG, there's no point of leaving
MUSB prepared for operation if a gadget driver fails
to probe. The same is valid for usb_gadget_unregister_driver(),
since we are removing the gadget driver and we don't have
OTG, we can completely unconfigure MUSB.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During development, even though board is wired
to e.g. OTG, we might want to compile host-only
or peripheral-only configurations.

Let's allow that to happen.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use bitmap_set()/bitmap_clear() to fill/zero a region of a bitmap
instead of doing set_bit()/clear_bit() each bit.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that ehci_run don't call ehci_reset, we can use ehci_run.
Signed-off-by: NMatthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

TDI driver does the ehci_reset in their reset callback.
Don't reset in ehci_run because configuration settings done in
platform driver will be reset.

This will allow to make msm use ehci_run.
Signed-off-by: NMatthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver private data is retrieved incorrectly which results
a crash when written into "mode" debugfs file.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below compiler warning

drivers/usb/otg/msm72k_otg.c:257: warning: 'msm_otg_suspend' defined but not used
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add const modifier before global variable realtek_cr_ids.
Signed-off-by: Nwwang <wei_wang@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix some sparse warning for realtek_cr patch
Signed-off-by: Nwwang <wei_wang@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

resumption of devices can fail. Errors must be handled.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The device never needs to be resumed in close(). But the counters
must be balanced. As resumption can fail, but the counters must
be balanced, use the _no_resume() version which cannot fail.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If an error happens during resumption.
The remaining data has to be cleanly discarded and the pm
counters have to be adjusted.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As soon as the first error happens, the write must
be stopped, lest we send mutilated messages.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

An error in the write code path would permanently disable
runtime PM in this driver
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes two errors:
- the device is busy if a message was recieved even if resubmission fails
- the device is not busy if resubmission fails due to -EPERM
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In function at91udc_probe()
call put_device() when device_register() fails.
Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The document says:
|2.1 Problem description
|    When at least two USB devices are simultaneously running, it is observed that
|    sometimes the INT corresponding to one of the USB devices stops occurring. This may
|    be observed sometimes with USB-to-serial or USB-to-network devices.
|    The problem is not noticed when only USB mass storage devices are running.
|2.2 Implication
|    This issue is because of the clearing of the respective Done Map bit on reading the ATL
|    PTD Done Map register when an INT is generated by another PTD completion, but is not
|    found set on that read access. In this situation, the respective Done Map bit will remain
|    reset and no further INT will be asserted so the data transfer corresponding to that USB
|    device will stop.
|2.3 Workaround
|    An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can
|    be implemented and if a certain Done bit is never set, verification of the PTD completion
|    can be done by reading PTD contents (valid bit).
|    This is a proven workaround implemented in software.

Russell King run into this with an USB-to-serial converter. This patch
implements his suggestion to enable the high frequent SOF interrupt only
at the time we have ATL packages queued. It goes even one step further
and enables the SOF interrupt only if we have more than one ATL packet
queued at the same time.

Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x]
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ehci_lpm_set_da and ehci_lpm_check are EHCI 1.1 specific functions which
are not used on many platforms but do generate annoying gcc warnings
Signed-off-by: NMaksim Rayskiy <mrayskiy@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We need FUSB300_MAX_NUM_EP (16) names otherwise the last 8 names get
initialized to garbage values in fusb300_probe().
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a patch that seems to make the USB hangs on the S3C244X go away.
At least a good amount of ping torture didn't make them come back so far.

The issue is that, if there are several back-to-back packets, sometimes no
interrupt is generated for one of them. This seems to be caused by the
mysterious dual packet mode, which the USB hardware enters automatically
if the endpoint size is half that of the FIFO. (On the 244X, this is the
normal situation for bulk data endpoints.)

There is also a timing factor in this. It seems that what happens is that
the USB hardware automatically sends an acknowledgement if there is only one
packet in the FIFO (the FIFO has space for two). If another packet arrives
before the host has retrieved and acknowledged the previous one, no interrupt
is generated for that second one.

However, there may be an indication. There is one undocumented bit (none
of the 244x manuals document it), OUT_CRS1_REG[1], that seems to be set
suspiciously often when this condition occurs. There is also
CLR_DATA_TOGGLE, OUT_CRS1_REG[7], which may have a function related to
this. (The Samsung manual is rather terse on that, as usual.)

This needs to be examined further. For now, the patch seems to do the
trick.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This PCH_UDC driver does not work normally when "Ethernet gadget" is used.

This patch fixed this issue.
The following was modified.
 - The FIFO flush process.
 - The descriptor creation process.
 - The adjustment of DMA buffer align.

Currently the PCH_UDC driver can work normally with "Ethernet gadget",
"Serial gadget" or "File-backed Storage Gadget".
Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reorder the driver->name assignment so the 'iProduct' could be initialized
as well if both 'name' and 'iProduct' come as NULL by default.

Also, remove the misplaced 'extern' keyword.
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While checking valid interface number we should compare MAX_CONFIG_INTERFACES
with the variable 'intf' (which holds the lower 8bits of w_index) rather than
'w_index'
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit b7d5b439.
It conflicts with commit baab93af "USB:
EHCI: ASPM quirk of ISOC on AMD Hudson" and merging the two just doesn't
work properly.

Cc: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

This reintroduces commit 47970b1b which was subsequently reverted
as f00eaeea.  The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space.  The normal capable() interface returns
true on success, but the LSM interface returns 0 on success.  This thinko
is now fixed in this patch, and has been confirmed to work properly.

So, once again...Eric Paris noted that commit de139a33 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: NEric Paris <eparis@redhat.com>
Tested-by: NDave Young <hidave.darkstar@gmail.com>
Acked-by: NJames Morris <jmorris@namei.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NJames Morris <jmorris@namei.org>

The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.

( Please note that Type 2 is not listed in Table 3 in Sec 6.2
  ("Required Structures and Data") of the SMBIOS v2.7
  Specification. )

Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.

Before the fix:
  (i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
 (ii) oops output:  Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6

After the fix:
  (i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
 (ii) oops output:  Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: NNaga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.

v2: testing options

v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852
https://bugzilla.kernel.org/show_bug.cgi?id=24462
https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Prevent divider overflow.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28932Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Currently when two or more buffers are queued by the camera driver
and so the double buffering is enabled in the idmac, we lose one
frame comming from CSI since the reporting of arrival of the first
frame is deferred by the DMAIC_7_EOF interrupt handler and reporting
of the arrival of the last frame is not done at all. So when requesting
N frames from the image sensor we actually receive N - 1 frames in
user space.

The reason for this behaviour is that the DMAIC_7_EOF interrupt
handler misleadingly assumes that the CUR_BUF flag is pointing to the
buffer used by the IDMAC. Actually it is not the case since the
CUR_BUF flag will be flipped by the FSU when the FSU is sending the
<TASK>_NEW_FRM_RDY signal when new frame data is delivered by the CSI.
When sending this singal, FSU updates the DMA_CUR_BUF and the
DMA_BUFx_RDY flags: the DMA_CUR_BUF is flipped, the DMA_BUFx_RDY
is cleared, indicating that the frame data is beeing written by
the IDMAC to the pointed buffer. DMA_BUFx_RDY is supposed to be
set to the ready state again by the MCU, when it has handled the
received data. DMAIC_7_CUR_BUF flag won't be flipped here by the
IPU, so waiting for this event in the EOF interrupt handler is wrong.
Actually there is no spurious interrupt as described in the comments,
this is the valid DMAIC_7_EOF interrupt indicating reception of the
frame from CSI.

The patch removes code that waits for flipping of the DMAIC_7_CUR_BUF
flag in the DMAIC_7_EOF interrupt handler. As the comment in the
current code denotes, this waiting doesn't help anyway. As a result
of this removal the reporting of the first arrived frame is not
deferred to the time of arrival of the next frame and the drivers
software flag 'ichan->active_buffer' is in sync with DMAIC_7_CUR_BUF
flag, so the reception of all requested frames works.

This has been verified on the hardware which is triggering the
image sensor by the programmable state machine, allowing to
obtain exact number of frames. On this hardware we do not tolerate
losing frames.

This patch also removes resetting the DMA_BUFx_RDY flags of
all channels in ipu_disable_channel() since transfers on other
DMA channels might be triggered by other running tasks and the
buffers should always be ready for data sending or reception.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Reviewed-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Makes debugging CS rejections much easier.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is an important security fix because we allowed arbitrary values
to be passed to AARESOLVE_OFFSET. This also puts the right buffer address
in the register.
Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also move ZB_DEPTHCLEARVALUE to the list of safe regs.
Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode.  The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode.  The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

My evergreen has been in a remote PC for week and reset has never once
saved me from certain doom, I finally relocated to the box with a
serial cable and noticed an oops when the GPU resets, and the TTM
delayed delete thread tries to remove something from the GTT.

This stops the delayed delete thread from executing across the GPU
reset handler, and woot I can GPU reset now.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Based on 6xx/7xx endian fixes from Cédric Cano.

v2: fix typo in shader
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

agd5f: minor cleanups
Signed-off-by: NCédric Cano <ccano@interfaceconcept.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

agd5f: additional cleanups/fixes
Signed-off-by: NCédric Cano <ccano@interfaceconcept.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>