Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

bgmac uses bcm47xx_nvram.h which is only available when BCM47XX was
selected. Earlier BCMA_HOST_SOC depended on BCM47XX so this was not
build on any other archs, but that changed. We should modify this
driver to get access to the nvram or the variables through platform
data.

This fixes a build problem in linux-next reported by Stephen Rothwell:

drivers/net/ethernet/broadcom/bgmac.c:19:27: fatal error: bcm47xx_nvram.h: No such file or directory
 #include <bcm47xx_nvram.h>
                           ^
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

taken from Ralink linux and windows drivers:

0x1b75, 0x7733 AirLive 450Mbps Wireless-N Dual Band USB Adapter
0x0b05, 0x17bc ASUS USB-N66 450Mbps Dual Band USB Adapter
0x0b05, 0x17ad ASUS USB-N66 Dual Band N Network Adapter
0x050d, 0x1103 Belkin Wireless Adapter
0x148f, 0xf301 Cameo Ralink3573 3x3 single band USB dongle
0x7392, 0x7733 Edimax
0x0e66, 0x0020 Hawking HD45U Dual Band USB Wireless-N Adapter
0x0e66, 0x0021 Hawking HD45U Dual Band Wls-450N Adapter
0x04bb, 0x094e I-O DATA WN-AG450U Wireless LAN Adapter
0x0789, 0x016b Logitec LAN-W450AN/U2
0x0846, 0x9012 NETGEAR WNDA4100 N900 Wireless Dual Band USB Adapter
0x0846, 0x9019 NETGEAR WNDA4200D Wireless Dual Band USB Adapter
0x2019, 0xed19 Planex GW-USDual450
0x148f, 0x3573 Ralink 802.11n USB Wireless LAN Card
0x0df6, 0x0067 Sitecom Wireless Dualband Network Adapter N750 X6
0x0df6, 0x006a Sitecom Wireless Dualband Network Adapter N900 X7
0x0586, 0x3421 ZyXEL Dual-Band Wireless N450 USB Adapter

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When antenna diversity combining is enabled in the EEPROM,
the initial values for the MAIN/ALT config have to be
programmed correctly. This patch adds it for AR9285.

Since the diversity combining macros are common to all chip
families, remove the redundant AR9285 macros and move the
definitions to phy.h.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We support maximum simultaneous 2 non-AP station interfaces and
they can assume role of Station/P2P client/P2P GO.
Advertise this support to cfg80211 so that concurrent P2P/STA
operation is possible.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We already have 'struct mwifiex_ie_types_header' with same
definition. Hence host_cmd_tlv is removed in this patch.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For PCIe cards, when wrong firmware is downloaded, firmware is
failed to be ready in 10 seconds. We should return an error at
this point. But currently we are sending first command to firmware.
As expected firmware doesn't respond to this command and command
timeout occurs.

This patch fixes the problem by removing unnecessary 'ret'
variable modifications in "if (ret) {" block.
The block is just supposed to update "adapter->winner" flag.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is observed that when wrong firmware is downloaded for
PCIe card, system hangs for 10 seconds. The reason is mdelay()
is used when firmware status is polled.

Replace mdelay with msleep(non-blocking API) to fix the issue.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After downloading the firmware, firmware status is checked by
reading a register. Polling interval is 100 msecs. Therefore 100
retries means the status is checked for 10 secs which is more than
sufficient for firmware to get ready.

This patch removes 1000 retries macro usage, because 100secs
time is not practical.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clear the data pointer stored in USB interface structure in
this handler. This helps to return from mwifiex_usb_disconnect()
if driver deinitialization is already performed while handling
an error path for mwifiex_usb_probe().

USB8797 card gets enumerated twice. First enumeration is for
firmware download and second enumeration expects firmware
initialization. mwifiex_usb_probe() always takes care of
deinitialization for first enumeration after firmware download.

Also, this change matches our handling for SDIO and PCIe
interfaces.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As if_ops.init_if() is called in mwifiex_register(),
corresponding cleanup routine should be called in
mwifiex_unregister().

Currently it's there in mwifiex_adapter_cleanup(), hence
interface specific cleanup is not performed if driver
initialization is failed.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is already there in mwifiex_unregister(). So unnecessary
call in mwifiex_adapter_cleanup() is removed in this patch.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently it is in mwifiex_adapter_cleanup() which doesn't get
called if driver initialization is failed causing memory leak.

scan_delay_timer is initialized in mwifiex_register(), so it
should be deleted in mwifiex_unregister(). Hence it has been
moved to appropriate place.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If reboot command is issued when device is in connected state,
system hangs while booting. This issue is fixed by doing cleanup
in shutdown handler.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is bug fix for an invalid boundry check for WPS IE.
We should check max IE length against defined macro; instead we were
checking it against size of pointer. Fix it.
Also move IE length check before allocation of memory.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During P2P handshake, P2P client needs to send deauth after EAPOL
FAILURE to GO. We need add bss mode for P2P client when handle deauth
request.

Without this change, deauth can not be sent out from P2P client side.
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before sending command to firmware, we need to check the frame type.
We skip registering the mgmt frame that has already been registered.
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some GO will send deauth or disassoc packet at the end of WPS
handshake, which causes P2P connecion failure due to the race
condition between event path and data path.
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In function 'mwifiex_write_data_complete' it need tx info to find
the mwifiex_private to updates statistics and wake up tx queues.
Or we may trigger tx queues timeout when transmitting lots of mgmt
frames.
Signed-off-by: NHuawei Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Delete packets from TX queues for this mwifiex_private structure
when bridged packet count reaches maximum threshold. Bridged packets
from each RA List are deleted till they fall to low threshold of 128.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Maintain total outstanding packet count for RA list instead of total
outstanding size as packet count metric seems more reasonable for
checking threshold etc.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

pkt_count is used to determine if BA can be formed on this RA list
by comparing it with randomly generated BA threshold. The pkt_count
variable name here is ambiguous and does not reflect its usage
correctly. Rename it to ba_pkt_count.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Under uAP mode mwifiex may stop all net tx queues on forwarding
packets. This may stop some tx queues and they never have chance
to be waked up. There is also no need to check tx_pending and
stop queues here. Because local host has such kind of check when
transmitting packets and it's not proper to have forwarding affect
local transmitting.
Signed-off-by: NHuawei Yang <harvey.huawei.yang@gmail.com>
Reviewed-by: NAvinash Patil <patila@marvell.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Steinar reported reallocations of skb->head with IPv6, leading to
a warning in skb_try_coalesce()

It turns out iwl3945 has several problems :

1) skb->truesize is underestimated.
   We really consume PAGE_SIZE bytes for a fragment,
   not the frame length.
2) 128 bytes of initial headroom is a bit low and forces reallocations.
3) We can avoid consuming a full page for small enough frames.
Reported-by: NSteinar H. Gunderson <sesse@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Paul Stewart <pstew@google.com>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In production code, don't use -Werror,
as it causes random compilation failures due to compiler version and options used.

With every new version of gcc, it becomes stricter and report more warnings.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The git tree is in github.com nowadays.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I forgot to add an entry to MAINTAINERS when submitting the driver.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for TCP and UDP HW checksum offloading.
RX chain is allways configured for offload mode.
In case of checksum error in RX path the DMA L4 error bit(5)
will be set to 1 and driver will drop the packet.
TX checksum offloading is configrable (ethtool -K).
TX descriptors are configured for checksum offload according
to the SKB protocol type (TCP/UDP, IPV4/6), Upon mismatch drop
the TX packet (checksum required but not TCP/UDP IPV4/6 type).
Signed-off-by: NKirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Release fragments in the order of allocation; including one for skb head
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Note that the driver doesn't directly use this field, but it should be
correctly defined in any case.
Signed-off-by: NSolomon Peachy <pizza@shaftnet.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* CUS217 specific initvals have to be programmed.
* iniAdditional is not used for AR9462/AR9565, remove it.
* Handle channel 2484 for regulatory compliance.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Right now, even though these chips support cross-band
FCC, the code is non-functional since we bail out early if
the channelFlags differ. Fix this so that cross-band
FCC works for cards that support this feature.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fast Channel Change across 2G/5G bands is supported
only by AR9462 and AR9565. Add a HW capability field
to indicate this.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Relegate 2 phy messages to debug status as they create excessive
log spam, noted in multiple bugzillas for brcmsmac v3.8 and up.
This is a follow on to net-next 99e94940:
brcmsmac: Reduce log spam in heavy tx, make err print in debug

 brcmsmac bcma0:0: phyerr 0x10, rate 0x14
 brcmsmac bcma0:0: brcms_c_ampdu_dotxstatus_complete:
ampdu tx phy error (0x10)
Signed-off-by: NJohn Greene <jogreene@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The return value of bcma_erom_get_addr_desc() is a unsigned value and it
could wrap around in the two complement writing. This happens for one
core in the BCM4708 SoC.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is better to return the actual error code than just -1.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These are the chipIDs of some ARM based SoCs from the BCM47xx line.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>