A patch from Sukumar Ghorai <s-ghorai@ti.com> changed the
nwires to use caps instead. However, nwires is still
needed for the earlier controller.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>

Disable CPUfreq since

1) is not yet supported in mainline, and
2) the current driver fails to suspend properly
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In working towards a smaller default kernel, only devices used for
early boot should be built in.  Toward that end, build the following
as modules by default:

- bluetooth
- audio: ALSA, ASoC
- WLAN

Uncompressed kernel size comparison:

Before:
   text	   data	    bss	    dec	    hex	filename
6557576	 465088	5616024	12638688	 c0d9e0	vmlinux

After:
   text	   data	    bss	    dec	    hex	filename
5616572	 436448	5610800	11663820	 b1f9cc	vmlinux
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable SMSC911x Ethernet driver for LogicPD's OMAP
3530 LV SOM and OMAP 35x Torpedo board.
Signed-off-by: NTim Nordell <tim.nordell@logicpd.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Introduce of a generic way to setup smsc911x based Ethernet
controller connected to GPMC similar to gpmc-smc91x but without
timing setup.
Signed-off-by: NTim Nordell <tim.nordell@logicpd.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add low-level initialization for hsmmc controller for
LogicPD's OMAP 3530 LV SOM and OMAP 35x Torpedo board.
Signed-off-by: NTim Nordell <tim.nordell@logicpd.com>
[tony@atomide.com: updated for the recent mmc platform init changes]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adding support for LogicPD's OMAP 3530 LV SOM and
OMAP 35x Torpedo board.
Signed-off-by: NTim Nordell <tim.nordell@logicpd.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Unnecessary cast from void* in assignment.
Signed-off-by: Nmatt mooney <mfm@muteddisk.com>
Acked-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

add support for TI HECC.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

add support for NAND flash.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

add support for hsusb host ports 1, 2 and on-module usb hub.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

add support for v3020 rtc.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add basic suppot, enable uart and led.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When changing the L3 clock frequency, the CPU is executing from internal RAM
and the SDRC clock is disabled. During this time accesses made to external
DDR are stalled. If the ARM subsystem attempts to access the DDR while the
SDRC clock is disabled this will stall the CPU until the access to the SDRC
timeouts. A timeout on the SDRC should never occur. Once a timeout occurs all
the following accesses will be aborted and the DDR is no longer accessible.

Although the code being executed in the internal RAM does not directly access
the DDR, it was found that the branch prediction logic in the CPU may cause
the CPU to prefetch code from a DDR location while the SDRC clock is disabled.
This was causing an SDRC timeout which resulted in a system hang.

This patch fixes this problem by ensuring the branch prediction logic is
disabled while changing the L3 clock frequency. The branch prediction logic
is disabled by clearing the Z-bit in the ARM CTRL register.

Disabling the branch prediction logic does not have any noticable impact
on the execution time of this code section. The hardware observability
signals were used to monitor the sdrc idle time with and without this
patch when operating at different CPU frequencies (150MHz, 500MHz and
600MHz) and the total sdrc idle time when changing frequenct was in
the range of 9-11us. This was measured on an omap3430 SDP running the
omapzoom p-android-omap-2.6.29 branch.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together

1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On OMAP4, control module is divided into 4 separate IPs
- OMAP44XX_CTRL_MODULE_CORE
- OMAP44XX_CTRL_MODULE_PAD_CORE
- OMAP44XX_CTRL_MODULE_WKUP
- OMAP44XX_CTRL_MODULE_PAD_WKUP

This patch adds all the omap4 control module register data and
includes them in the common control.h

The register data is autogenerated from the codebase thanks
to Benoit Cousson efforts
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.

This APIs will work only for OMAP4
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On omap4 control module is divided in four IP blocks.
- CTRL_MODULE_CORE			0x4a002000
- CTRL_MODULE_PAD_CORE		0x4a100000
- CTRL_MODULE_WKUP			0x4a30c000
- CTRL_MODULE_PAD_WKUP		0x4a31e000

Addressing all the modules with single base address is not possible
considering 16 bit offsets. The mux code manages the pad core and pad
wakeup related base address inside the mux framework. For other usage
only control core and control pad bases are necessary. So this patch
maps only needed pad control base address which is used by device drivers
and infrastructure code

The main control core base is still kept same in this patch to
keep git-bisect working. This will be fixed in the relevant patch
in this series.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Fix a few OMAP4430 clock tree problems after the recent manual merge of the
various ES2 clock patches:

- usim optional clock and its parent had the same name, rename the parent
usim_fclk -> usim_ck

- OPTFCLKEN_CLK32K is not handled anymore by the USBPHYOCP2SCP module in ES2
Create a new clock that belongs to CM_ALWON_USBPHY_CLKCTRL register

This patch depends on some of the PRCM macro updates from Rajendra.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: tweaked patch description]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>

DSS on ES2 supports only OSWR, hence remove the support
for CSWR from the powerdomain framework.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

4430 ES2 has a few new registers added and a few modified
from ES1. This patch adds all the register changes in PRM
and CM for OMAP4430 ES2.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

This patch updates the PRM and CM register bitshifts and masks
for OMAP4430 ES2.0.

Replace as well the BITFIELD macro with the shift operator in order
to be consistent with the previous OMAP2 & 3 format.

Sort the register list in comments in order to have a consistent
register order and avoid futur change during code generation.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

OMAP4 IP optional clocks require explicit enable in module CTRLCLK
register. In order to allow that we have to create artificial clock
nodes that represent this clock inputs in the IP.

Notes:
- Temporary use OMAP3 names for GPIO optional clocks until the GPIO hwmod
convertion is done. It will enforce the usage of OMAP4 names as the reference.
- Temporary use OMAP3 names for TIMER main clock (gptX_fck) until TIMER hwmod
convertion is done. During that convertion, the new name will have to be used.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>

The OMAP4 hwmod data introduced the new naming convention for TI
IPs (See patch OMAP4: hwmod: Add partial hwmod support for OMAP4430 ES1.0)

The leaf clock names are using the same IP name and thus must be
modified to match the clock populated in the hwmod data.

- Fix some leaf clocks nodes that were using a _iclk instead of the _fclk
prefix.
- Fix some wrong interface clock name for master IPs connected to
interconnect.

Please not that due to the fact that nodes are sorted by name, the name
change will introduce a quite ugly diff a little bit hard to follow.

Timers clock con_id is still using the old gptX_fck name until the
gptimer driver is updated to omap_device framework.
Timers entries in hwmods DB are still disabled until the migration
if timer to platform_driver + omap_hwmod.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: manually resolved conflicts with Rajendra's clock patch]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>

This patch updates the clock tree with all the
changes in OMAP4430 ES2.

clock nodes added
-1- tie_low_clock_ck
-2- abe_dpll_bypass_clk_mux_ck

clock nodes deleted
-1- dpll_sys_ref_clk
-2- per_sgx_fclk
-3- usbphyocp2scp_ick
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: added comment re ES1 clocks to top of file]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

update OMAP Kconfig help texts for all supported SoC models
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This 'legacy' OMAP2420 McBSP2 muxing code is currently broken after recent
conversion to new mux code. The omap_mcbsp_request calling this code is
usually called after booting whereas the omap_mux_init_signal is __init
marked so null pointer dereference would occur.

Fix this by removing the muxing code and let the bootloader or board file to
do it if necessary. Remove also omap2_mcbsp_ops as there is no use for it.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McBSP SRG (Sample Rate Generator) and FSG (Frame Sync
Generator) is only needed to be enabled, when McBSP
is master.
In McBSP slave mode, the SRG, and FSG can be kept disabled,
which might save some power at the end in this configuration.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Added defines to avoid compilation error.
Signed-off-by: NSubramaniam C.A <subramaniam.ca@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Updates to enable omap aes
Signed-off-by: NDmitry Kasatkin <dmitry.kasatkin@nokia.com>
[tony@atomide.com: updated to use CONFIG_ARCH_OMAP2/3 instead of old 24XX/34XX]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix this and similar build warnings when building with
omap_4430sdp_defconfig.

 CC      arch/arm/mach-omap2/board-4430sdp.o
In file included from arch/arm/mach-omap2/board-4430sdp.c:36:
arch/arm/plat-omap/include/plat/usb.h:109: warning: return type defaults to 'int'
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

At Pandaboard we have 2 status leds, so adding them with similar usage as
we have for Beagleboard (heartbeat and mmc0). The patch basically adds the
platform data required by leds-gpio driver.
Signed-off-by: NRicardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap 4430sdp board support for the  proximity sensor via GPIO keys.
The proximity sensor is connected to GPIO and is registered as a
GPIO key.
- Making the default state of the sensor off at bootup
- The init is called before platform_add_devices
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Merge branch 'omap_for_2.6.37' of git://dev.omapzoom.org/pub/scm/santosh/kernel-omap4-base into omap-for-linus