Change the code to allow making all the rate control ops
const, nothing ever needs to change them. Also change all
drivers to make use of this and mark the ops const.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The threshold values for RX interrupt mitigation
are different for AR9003 and AR9002 families.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: Process GTT interrupts" accidentally
had a line that was commented out.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch will also change behavior of rx_beacons statistic.
Instead of collecting all received beacons, it will collect only
ours. This, IMO make more sense, since for troubleshooting we will
need to know count of our beacons, or both.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

this function is used by most ath driver, so it can be moved here.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes bug found by the kbuild test robot:

tree:   git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head:   1e2f9295
commit: 1cbbcb08 [135/140] wil6210: prefetch head of packet
config: make ARCH=microblaze allyesconfig

All error/warnings:

   drivers/net/wireless/ath/wil6210/txrx.c: In function 'wil_vring_reap_rx':
>> drivers/net/wireless/ath/wil6210/txrx.c:381:2: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration]
     prefetch(skb->data);
     ^
   cc1: some warnings being treated as errors

vim +/prefetch +381 drivers/net/wireless/ath/wil6210/txrx.c

   375                  wil_err(wil, "Rx size too large: %d bytes!\n", dmalen);
   376                  kfree_skb(skb);
   377                  return NULL;
   378          }
   379          skb_trim(skb, dmalen);
   380
 > 381          prefetch(skb->data);
   382
   383          wil_hex_dump_txrx("Rx ", DUMP_PREFIX_OFFSET, 16, 1,
   384                            skb->data, skb_headlen(skb), false);
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prevent a possible overflow condition which results in occasional
bad IQ coefficients and EVM numbers.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug in the TX IQ calibration post
processing routine because of which the driver disables
TX IQ correction even though the calibration results
are valid. This fix is applicable for all chips in the
AR9003 family.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

debug_sta.c: ath_debug_rate_stats() error: buffer overflow 'rstats->ht_stats' 24 <= 24

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.

Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).

This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This would be useful when debugging RX performance issues.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also, rename node_stat to node_aggr.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The REGULATORY_CUSTOM_REG can be used during early init with
the goal of overriding the wiphy's default regulatory settings
in case the alpha2 of the device is not known. In the case that
the alpha2 becomes known lets avoid having drivers having to
clear the REGULATORY_CUSTOM_REG flag by doing it for them
when regulatory_hint() is used.

Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath wants to first apply the custom regd and only later
will it revert to not using it if an alpha2 regulatory
domain is found. Since the wireless core now enforces
usage of the REGULATORY_CUSTOM_REG strictly when
wiphy_apply_custom_regulatory() is used this makes
ath adhere to the expected behaviour but also updates
the wiphy after its done with the custom usage.

This fixes this warning:

[    5.488733] ath: phy0: ASPM enabled: 0x43
[    5.488735] ath: EEPROM regdomain: 0x0
[    5.488736] ath: EEPROM indicates default country code should be used
[    5.488736] ath: doing EEPROM country->regdmn map search
[    5.488737] ath: country maps to regdmn code: 0x3a
[    5.488737] ath: Country alpha2 being used: US
[    5.488738] ath: Regpair used: 0x3a
[    5.488738] ------------[ cut here ]------------
[    5.488745] WARNING: CPU: 0 PID: 161 at
	/home/sujith/dev/wireless-testing/net/wireless/reg.c:1361
	wiphy_apply_custom_regulatory+0x17a/0x1b0 [cfg80211]()
[    5.488746] wiphy should have REGULATORY_CUSTOM_REG

The wireless core can *later* lift this flag for us for when
using the regulatory_hint() to make this fix more generic.
Reported-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add set_bitrate_mask callback. Currently
ath10k HW is limited to handle only single
fixed rate setting or limit number of used
spatial streams.

Example:
iw wlanX set bitrates legacy-5 ht-mcs-5 vht-mcs-5 2:9
will setup VHT, nss=2, mcs=9

iw wlanX set bitrates legacy-5 18 ht-mcs-5 vht-mcs-5
will setup legacy, 18Mbps

iw wlanX set bitrates legacy-5 ht-mcs-5 3 vht-mcs-5
will setup HT, nss=1, mcs=3

iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9
will setup nss=1

iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9 2:0-9
will setup nss=2
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:

echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog

And to put back firmare defaults use 0x0:

echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Send firmware WMI debug logs to user space for further processing.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware can send simple ascii strings as debug messages using
WMI_DEBUG_PRINT_EVENTID, print those with ATH10K_DBG_WMI log level.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.

10.X firmware support up to 127 peers, non-AP centric firmwares 16.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently ath10k is not using STA KICKOUT firmware functionality.
In order to avoid unwanted WMI_PEER_STA_KICKOUT_EVENT event this functionality
should be disabled when not used.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add Kconfig option that allow DFS functionality.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.

Cc: stable@vger.kernel.org
Reported-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.

To avoid this, use the current channel information
maintained in the driver.

Cc: stable@vger.kernel.org
Reported-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Add new AR9565 1.0/1.0.1/1.1 IDs
* Change Dell/Lenovo/Samsung cards to 2-Antenna with diversity.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As soon as skb is ready to be reaped, prefetch 1-st cache line.
This accelerates data access that is performed later, during the
packet classification by the driver and IP stack.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bit DMA_CFG_DESC_TX_OFFLOAD_CFG_L3T_IPV4_POS should be set for IPv4
only. Don't set it for IPv6
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use hardware capabilities to limit IRQ generation to about 15 per msec
It corresponds to about 7 packets/IRQ when running iperf with default
parameters at 1.3Gbps

Do not enable this feature in the sniffer (monitor)  mode, because
interrupt moderation cause timestamp accuracy deterioration.
For the sniffer flow, it is important to get precise timestamp.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The maximum permissible values for noise floor in ETSI
and Japan domains have been updated with new EU
regulations for CCA detection. Adjust the values in the
driver accordingly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR955x has problems with RX sensitivity in 2G. This patch
adds a routine to select range_osdac dynamically on a
per-chain basis to address this issue.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>