Add externally visible functions to lookup a UDP socket by skb. This
will be used for GRO in UDP sockets. These functions also check
if skb->dst is set, and if it is not skb->dev is used to get dev_net.
This allows calling lookup functions before dst has been set on the
skbuff.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable peeking at UDP datagrams at the offset specified with socket
option SOL_SOCKET/SO_PEEK_OFF. Peek at any datagram in the queue, up
to the end of the given datagram.

Implement the SO_PEEK_OFF semantics introduced in commit ef64a54f
("sock: Introduce the SO_PEEK_OFF sock option"). Increase the offset
on peek, decrease it on regular reads.

When peeking, always checksum the packet immediately, to avoid
recomputation on subsequent peeks and final read.

The socket lock is not held for the duration of udp_recvmsg, so
peek and read operations can run concurrently. Only the last store
to sk_peek_off is preserved.
Signed-off-by: NSam Kumar <samanthakumar@google.com>
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove UDP transport headers before queueing packets for reception.
This change simplifies a follow-up patch to add MSG_PEEK support.
Signed-off-by: NSam Kumar <samanthakumar@google.com>
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Herbert would like not touching UDP socket refcnt for encapsulated
traffic. For this to happen, we need to use normal RCU rules, with a grace
period before freeing a socket. UDP sockets are not short lived in the
high usage case, so the added cost of call_rcu() should not be a concern.

This actually removes a lot of complexity in UDP stack.

Multicast receives no longer need to hold a bucket spinlock.

Note that ip early demux still needs to take a reference on the socket.

Same remark for functions used by xt_socket and xt_PROXY netfilter modules,
but this might be changed later.

Performance for a single UDP socket receiving flood traffic from
many RX queues/cpus.

Simple udp_rx using simple recvfrom() loop :
438 kpps instead of 374 kpps : 17 % increase of the peak rate.

v2: Addressed Willem de Bruijn feedback in multicast handling
 - keep early demux break in __udp4_lib_demux_lookup()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, SOL_TIMESTAMPING can only be enabled using setsockopt.
This is very costly when users want to sample writes to gather
tx timestamps.

Add support for enabling SO_TIMESTAMPING via control messages by
using tsflags added in `struct sockcm_cookie` (added in the previous
patches in this series) to set the tx_flags of the last skb created in
a sendmsg. With this patch, the timestamp recording bits in tx_flags
of the skbuff is overridden if SO_TIMESTAMPING is passed in a cmsg.

Please note that this is only effective for overriding the recording
timestamps flags. Users should enable timestamp reporting (e.g.,
SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_OPT_ID) using
socket options and then should ask for SOF_TIMESTAMPING_TX_*
using control messages per sendmsg to sample timestamps for each
write.
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Process socket-level control messages by invoking
__sock_cmsg_send in ip6_datagram_send_ctl for control messages on
the SOL_SOCKET layer.

This makes sure whenever ip6_datagram_send_ctl is called for
udp and raw, we also process socket-level control messages.

This is a bit uglier than IPv4, since IPv6 does not have
something like ipcm_cookie. Perhaps we can later create
a control message cookie for IPv6?

Note that this commit interprets new control messages that
were ignored before. As such, this commit does not change
the behavior of IPv6 control messages.
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv6 counters updates use a different macro than IPv4.

Fixes: 36cbb245 ("udp: Increment UDP_MIB_IGNOREDMULTI for arriving unmatched multicasts")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Rick Jones <rick.jones2@hp.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv4 interprets a negative return value from a protocol handler as a
request to redispatch to a new protocol.  In contrast, IPv6 interprets a
negative value as an error, and interprets a positive value as a request
for redispatch.

UDP for IPv6 was unaware of this difference.  Change __udp6_lib_rcv() to
return a positive value for redispatch.  Note that the socket's
encap_rcv hook still needs to return a negative value to request
dispatch, and in the case of IPv6 packets, adjust IP6CB(skb)->nhoff to
identify the byte containing the next protocol.
Signed-off-by: NBill Sommerfeld <wsommerfeld@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ipv4,  when  the machine receives a ICMP_FRAG_NEEDED message,  the
connected UDP socket will get EMSGSIZE message on its next read from the
socket.
However, this is not the case for ipv6.
This fix modifies the udp err handler in Ipv6 for ICMP6_PKT_TOOBIG to
make it similar to ipv4 behavior. That is when the machine gets an
ICMP6_PKT_TOOBIG message, the connected UDP socket will get EMSGSIZE
message on its next read from the socket.
Signed-off-by: NWei Wang <weiwan@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to support fast lookups for TCP sockets with SO_REUSEPORT,
the function that adds sockets to the listening hash set needs
to be able to check receive address equality.  Since this equality
check is different for IPv4 and IPv6, we will need two different
socket hashing functions.

This patch adds inet6_hash identical to the existing inet_hash function
and updates the appropriate references.  A following patch will
differentiate the two by passing different comparison functions to
__inet_hash.

Additionally, in order to use the IPv6 address equality function from
inet6_hashtables (which is compiled as a built-in object when IPv6 is
enabled) it also needs to be in a built-in object file as well.  This
moves ipv6_rcv_saddr_equal into inet_hashtables to accomplish this.
Signed-off-by: NCraig Gallek <kraig@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using a combination of connected and un-connected sockets, Dmitry
was able to trigger soft lockups with his fuzzer.

The problem is that sockets in the SO_REUSEPORT array might have
different scores.

Right after sk2=socket(), setsockopt(sk2,...,SO_REUSEPORT, on) and
bind(sk2, ...), but _before_ the connect(sk2) is done, sk2 is added into
the soreuseport array, with a score which is smaller than the score of
first socket sk1 found in hash table (I am speaking of the regular UDP
hash table), if sk1 had the connect() done, giving a +8 to its score.

hash bucket [X] -> sk1 -> sk2 -> NULL

sk1 score = 14  (because it did a connect())
sk2 score = 6

SO_REUSEPORT fast selection is an optimization. If it turns out the
score of the selected socket does not match score of first socket, just
fallback to old SO_REUSEPORT logic instead of trying to be too smart.

Normal SO_REUSEPORT users do not mix different kind of sockets, as this
mechanism is used for load balance traffic.

Fixes: e32ea7e7 ("soreuseport: fast reuseport UDP socket selection")
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Craig Gallek <kraigatgoog@gmail.com>
Acked-by: NCraig Gallek <kraig@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This socket-lookup path did not pass along the skb in question
in my original BPF-based socket selection patch.  The skb in the
udpN_lib_lookup2 path can be used for BPF-based socket selection just
like it is in the 'traditional' udpN_lib_lookup path.

udpN_lib_lookup2 kicks in when there are greater than 10 sockets in
the same hlist slot.  Coincidentally, I chose 10 sockets per
reuseport group in my functional test, so the lookup2 path was not
excersised. This adds an additional set of tests with 20 sockets.

Fixes: 538950a1 ("soreuseport: setsockopt SO_ATTACH_REUSEPORT_[CE]BPF")
Fixes: 3ca8e402 ("soreuseport: BPF selection functional test")
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NCraig Gallek <kraig@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Expose socket options for setting a classic or extended BPF program
for use when selecting sockets in an SO_REUSEPORT group.  These options
can be used on the first socket to belong to a group before bind or
on any socket in the group after bind.

This change includes refactoring of the existing sk_filter code to
allow reuse of the existing BPF filter validation checks.
Signed-off-by: NCraig Gallek <kraig@google.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Include a struct sock_reuseport instance when a UDP socket binds to
a specific address for the first time with the reuseport flag set.
When selecting a socket for an incoming UDP packet, use the information
available in sock_reuseport if present.

This required adding an additional field to the UDP source address
equality function to differentiate between exact and wildcard matches.
The original use case allowed wildcard matches when checking for
existing port uses during bind.  The new use case of adding a socket
to a reuseport group requires exact address matching.

Performance test (using a machine with 2 CPU sockets and a total of
48 cores):  Create reuseport groups of varying size.  Use one socket
from this group per user thread (pinning each thread to a different
core) calling recvmmsg in a tight loop.  Record number of messages
received per second while saturating a 10G link.
  10 sockets: 18% increase (~2.8M -> 3.3M pkts/s)
  20 sockets: 14% increase (~2.9M -> 3.3M pkts/s)
  40 sockets: 13% increase (~3.0M -> 3.4M pkts/s)

This work is based off a similar implementation written by
Ying Cai <ycai@google.com> for implementing policy-based reuseport
selection.
Signed-off-by: NCraig Gallek <kraig@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Backport of this upstream commit into stable kernels :
89c22d8c ("net: Fix skb csum races when peeking")
exposed a bug in udp stack vs MSG_PEEK support, when user provides
a buffer smaller than skb payload.

In this case,
skb_copy_and_csum_datagram_iovec(skb, sizeof(struct udphdr),
                                 msg->msg_iov);
returns -EFAULT.

This bug does not happen in upstream kernels since Al Viro did a great
job to replace this into :
skb_copy_and_csum_datagram_msg(skb, sizeof(struct udphdr), msg);
This variant is safe vs short buffers.

For the time being, instead reverting Herbert Xu patch and add back
skb->ip_summed invalid changes, simply store the result of
udp_lib_checksum_complete() so that we avoid computing the checksum a
second time, and avoid the problematic
skb_copy_and_csum_datagram_iovec() call.

This patch can be applied on recent kernels as it avoids a double
checksumming, then backported to stable kernels as a bug fix.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses multiple problems :

UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.

Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())

This patch adds full RCU protection to np->opt
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SO_INCOMING_CPU as added in commit 2c8c56e1 was a getsockopt() command
to fetch incoming cpu handling a particular TCP flow after accept()

This commits adds setsockopt() support and extends SO_REUSEPORT selection
logic : If a TCP listener or UDP socket has this option set, a packet is
delivered to this socket only if CPU handling the packet matches the specified
one.

This allows to build very efficient TCP servers, using one listener per
RX queue, as the associated TCP listener should only accept flows handled
in softirq by the same cpu.
This provides optimal NUMA behavior and keep cpu caches hot.

Note that __inet_lookup_listener() still has to iterate over the list of
all listeners. Following patch puts sk_refcnt in a different cache line
to let this iteration hit only shared and read mostly cache lines.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change brace placement to be in line with coding standards
Signed-off-by: NIan Morris <ipm@chirality.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have two problems in UDP stack related to bogus checksums :

1) We return -EAGAIN to application even if receive queue is not empty.
   This breaks applications using edge trigger epoll()

2) Under UDP flood, we can loop forever without yielding to other
   processes, potentially hanging the host, especially on non SMP.

This patch is an attempt to make things better.

We might in the future add extra support for rt applications
wanting to better control time spent doing a recv() in a hostile
environment. For example we could validate checksums before queuing
packets in socket receive queue.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit <5cf3d461> ("udp: Simplify__udp*_lib_mcast_deliver")
simplified the filter for incoming IPv6 multicast but removed
the check of the local socket address and the UDP destination
address.

This patch restores the filter to prevent sockets bound to a IPv6
multicast IP to receive other UDP traffic link unicast.
Signed-off-by: NHenning Rogge <hrogge@gmail.com>
Fixes: 5cf3d461 ("udp: Simplify__udp*_lib_mcast_deliver")
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSheng Yong <shengyong1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x != NULL and sometimes as x. x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.

No changes detected by objdiff.
Signed-off-by: NIan Morris <ipm@chirality.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x == NULL and sometimes as !x. !x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.

No changes detected by objdiff.
Signed-off-by: NIan Morris <ipm@chirality.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

const qualifiers ease code review by making clear
which objects are not written in a function.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.

Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: NAl Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds the same functionaliy to IPv6 that
commit 903ab86d
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date:   Tue Mar 1 02:36:48 2011 +0000

    udp: Add lockless transmit path

added to IPv4.

UDP transmit path can now run without a socket lock,
thus allowing multiple threads to send to a single socket
more efficiently.
This is only used when corking/MSG_MORE is not used.
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we can individually construct IPv6 skbs to send, add a
udpv6_send_skb() function to populate the udp header and send the
skb.  This allows udp_v6_push_pending_frames() to re-use this
function as well as enables us to add lockless sendmsg() support.
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move convert_csum from udp_sock to inet_sock. This allows the
possibility that we can use convert checksum for different types
of sockets and also allows convert checksum to be enabled from
inet layer (what we'll want to do when enabling IP_CHECKSUM cmsg).
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The compute_score functions are a bit difficult to read.

Neaten them a bit to reduce object sizes and make them a
bit more intelligible.

Return early to avoid indentation and avoid unnecessary
initializations.

(allyesconfig, but w/ -O2 and no profiling)

$ size net/ipv[46]/udp.o.*
   text    data     bss     dec     hex filename
  28680    1184      25   29889    74c1 net/ipv4/udp.o.new
  28756    1184      25   29965    750d net/ipv4/udp.o.old
  17600    1010       2   18612    48b4 net/ipv6/udp.o.new
  17632    1010       2   18644    48d4 net/ipv6/udp.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This change has no functional impact and simply addresses some coding
style issues detected by checkpatch. Specifically this change
adjusts "if" statements which also include the assignment of a
variable.

No changes to the resultant object files result as determined by objdiff.
Signed-off-by: NIan Morris <ipm@chirality.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the more common dynamic_debug capable net_dbg_ratelimited
and remove the LIMIT_NETDEBUG macro.

All messages are still ratelimited.

Some KERN_<LEVEL> uses are changed to KERN_DEBUG.

This may have some negative impact on messages that were
emitted at KERN_INFO that are not not enabled at all unless
DEBUG is defined or dynamic_debug is enabled.  Even so,
these messages are now _not_ emitted by default.

This also eliminates the use of the net_msg_warn sysctl
"/proc/sys/net/core/warnings".  For backward compatibility,
the sysctl is not removed, but it has no function.  The extern
declaration of net_msg_warn is removed from sock.h and made
static in net/core/sysctl_net_core.c

Miscellanea:

o Update the sysctl documentation
o Remove the embedded uses of pr_fmt
o Coalesce format fragments
o Realign arguments
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alternative to RPS/RFS is to use hardware support for multiple
queues.

Then split a set of million of sockets into worker threads, each
one using epoll() to manage events on its own socket pool.

Ideally, we want one thread per RX/TX queue/cpu, but we have no way to
know after accept() or connect() on which queue/cpu a socket is managed.

We normally use one cpu per RX queue (IRQ smp_affinity being properly
set), so remembering on socket structure which cpu delivered last packet
is enough to solve the problem.

After accept(), connect(), or even file descriptor passing around
processes, applications can use :

 int cpu;
 socklen_t len = sizeof(cpu);

 getsockopt(fd, SOL_SOCKET, SO_INCOMING_CPU, &cpu, &len);

And use this information to put the socket into the right silo
for optimal performance, as all networking stack should run
on the appropriate cpu, without need to send IPI (RPS/RFS).
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As NIC multicast filtering isn't perfect, and some platforms are
quite content to spew broadcasts, we should not trigger an event
for skb:kfree_skb when we do not have a match for such an incoming
datagram.  We do though want to avoid sweeping the matter under the
rug entirely, so increment a suitable statistic.

This incorporates feedback from David L. Stevens, Karl Neiss and Eric
Dumazet.

V3 - use bool per David Miller
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This encapsulates all of the skb_copy_datagram_iovec() callers
with call argument signature "skb, offset, msghdr->msg_iov, length".

When we move to iov_iters in the networking, the iov_iter object will
sit in the msghdr.

Having a helper like this means there will be less places to touch
during that transformation.

Based upon descriptions and patch from Al Viro.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for doing CHECKSUM_UNNECESSARY to CHECKSUM_COMPLETE
conversion in UDP tunneling path.

In the normal UDP path, we call skb_checksum_try_convert after locating
the UDP socket. The check is that checksum conversion is enabled for
the socket (new flag in UDP socket) and that checksum field is
non-zero.

In the UDP GRO path, we call skb_gro_checksum_try_convert after
checksum is validated and checksum field is non-zero. Since this is
already in GRO we assume that checksum conversion is always wanted.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes no changes to the logic of the code but simply addresses
coding style issues as detected by checkpatch.

Both objdump and diff -w show no differences.

A number of items are addressed in this patch:
* Multiple spaces converted to tabs
* Spaces before tabs removed.
* Spaces in pointer typing cleansed (char *)foo etc.
* Remove space after sizeof
* Ensure spacing around comparators such as if statements.
Signed-off-by: NIan Morris <ipm@chirality.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace open codings of (((u64) <x> * <y>) >> 32) with reciprocal_scale().
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>