Currently in probe
pm_runtime_put(dev->dev);

...
        /* i2c device drivers may be active on return from add_adapter() */
        adap->nr = pdev->id;
        r = i2c_add_numbered_adapter(adap);
        if (r) {
                dev_err(dev->dev, "failure adding adapter\n");
                goto err_free_irq;
        }
...

return 0;

err_free_irq:
        free_irq(dev->irq, dev);
err_unuse_clocks:
        omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
        pm_runtime_put(dev->dev);

This may access the i2c registers without the clocks in the error cases.
Fix the same by moving the pm_runtime_put after the error check.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

On OMAP4 we were writing 1 to IRQENABLE_CLR which cleared only
the arbitration lost interrupt. The patch intends to fix the same by writing 0
to the IE register clearing all interrupts.

This is based on the work done by Vikram Pandita <vikram.pandita@ti.com>.

The  changes from the original patch ...
-  Does not use the IRQENABLE_CLR register to clear as it is not mentioned
  to be legacy register IRQENABLE_CLR helps in  atomically
  setting/clearing specific interrupts, instead use the OMAP_I2C_IE_REG as we
  are clearing all interrupts.

Cc: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Currently the i2c driver calls the pm_runtime_enable and never
the disable. This may cause a warning when pm_runtime_enable
checks for the count match.Fix the same by calling
pm_runtime_disable in the error and the remove path.

Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The functions omap_i2c_unidle/idle are called from omap_i2c_runtime_resume
and omap_i2c_runtime_suspend which is compiled for CONFIG_PM_RUNTIME.
This patch removes the omap_i2c_unidle/idle functions and folds them
into the runtime callbacks.

This fixes the below warn when CONFIG_PM_RUNTIME is not defined

 CC      arch/arm/mach-omap2/board-ti8168evm.o
drivers/i2c/busses/i2c-omap.c:272: warning: 'omap_i2c_unidle' defined but not used
drivers/i2c/busses/i2c-omap.c:293: warning: 'omap_i2c_idle' defined but not used
  CC      net/ipv4/ip_forward.o
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

gpio-i2c describes an I2C controller (using gpios for data and clock),
so it must be described in i2c, not gpio.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Pull ARM SoC fixes from Olof Johansson:
 "Another week, another batch of fixes.

  All are small, contained, targeted fixes for explicit problems --
  mostly build and boot failures across i.MX, OMAP, Renesas/Shmobile and
  Samsung."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: imx6q: fix suspend regression caused by common clk migration
  ARM: OMAP4470: Fix OMAP4470 boot failure
  ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
  ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
  ARM: shmobile: r8a7779: Route all interrupts to ARM
  ARM: shmobile: kzm9d: use late init machine hook
  ARM: shmobile: kzm9g: use late init machine hook
  ARM: mach-shmobile: armadillo800eva: Use late init machine hook
  ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
  ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
  ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
  ARM: shmobile: sh7372: bugfix: chclr_offset base
  ARM: shmobile: sh73a0: bugfix: SY-DMAC number
  ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL

Fix kernel-doc warnings in printk.c: use correct parameter name.

  Warning(kernel/printk.c:2429): No description found for parameter 'buf'
  Warning(kernel/printk.c:2429): Excess function parameter 'line' description in 'kmsg_dump_get_buffer'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc warning.  This struct member was removed in commit
87568264 ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.

  Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'v3.5-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

* 'v3.5-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
  ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
  ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL

When moving to common clk framework, the imx6q clks rom and mmdc_ch1_axi
get different on/off states than old clk driver, which breaks suspend
function.  There might be a better way to manage these clocks, but let's
takes the old clk driver approach to fix the regression first.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'omap-fixes-for-v3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
"Here's one more regression fix that I missed earlier, and a
 trivial fix to get omap4470 booting."

* tag 'omap-fixes-for-v3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP4470: Fix OMAP4470 boot failure
  ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n

Pull ACPI & Power Management patches from Len Brown.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  acpi_pad: fix power_saving thread deadlock
  ACPI video: Still use ACPI backlight control if _DOS doesn't exist
  ACPI, APEI, Avoid too much error reporting in runtime
  ACPI: Add a quirk for "AMILO PRO V2030" to ignore the timer overriding
  ACPI: Remove one board specific WARN when ignoring timer overriding
  ACPI: Make acpi_skip_timer_override cover all source_irq==0 cases
  ACPI, x86: fix Dell M6600 ACPI reboot regression via DMI
  ACPI sysfs.c strlen fix

Pull driver Core fixes from Greg Kroah-Hartman:
 "Here is a number of printk() fixes, specifically a few reported by the
  crazy blog program that ships in SUSE releases (that's "boot log" and
  not "web log", it predates the general "blog" terminology by many
  years), and the restoration of the continuation line functionality
  reported by Stephen and others.  Yes, the changes seem a bit big this
  late in the cycle, but I've been beating on them for a while now, and
  Stephen has even optimized it a bit, so all looks good to me.

  The other change in here is a Documentation update for the stable
  kernel rules describing how some distro patches should be backported,
  to hopefully drive a bit more response from the distros to the stable
  kernel releases.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'driver-core-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  printk: Optimize if statement logic where newline exists
  printk: flush continuation lines immediately to console
  syslog: fill buffer with more than a single message for SYSLOG_ACTION_READ
  Revert "printk: return -EINVAL if the message len is bigger than the buf size"
  printk: fix regression in SYSLOG_ACTION_CLEAR
  stable: Allow merging of backports for serious user-visible performance issues

Merge branches 'acpi_pad-bugzilla-42981', 'apei-bugzilla-43282', 'video-bugzilla-43168', 'bugzilla-40002' and 'bugfix-misc' into release

bug fixes

The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread.  The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu().  This
patch fixes the issue by making round_robin_cpu() use its own mutex.

https://bugzilla.kernel.org/show_bug.cgi?id=42981

Cc: stable@vger.kernel.org
Signed-off-by: NStuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This fixes a regression in 3.4-rc1 caused by commit
ea9f8856
(ACPI video: Harden video bus adding.)

Some platforms don't have _DOS control method, but the ACPI
backlight still works.
We should not invoke _DOS for these platforms.

https://bugzilla.kernel.org/show_bug.cgi?id=43168

Cc: Igor Murzov <intergalactic.anonymous@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Pull power management fixes from Rafael J. Wysocki:

 * Fix for a bug in async suspend error code path causing parents to
   wait forever for their children in case of a suspend error from
   Mandeep Singh Baines (-stable metarial).

 * Fix for a suspend regression related to earlier changes in the ACPI
   cpuidle driver from Deepthi Dharwar.

* tag 'pm-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / ACPI: Fix suspend/resume regression caused by cpuidle cleanup.
  PM / Sleep: Prevent waiting forever on asynchronous suspend after abort

In reviewing Kay's fix up patch: "printk: Have printk() never buffer its
data", I found two if statements that could be combined and optimized.

Put together the two 'cont.len && cont.owner == current' if statements
into a single one, and check if we need to call cont_add(). This also
removes the unneeded double cont_flush() calls.

Link: http://lkml.kernel.org/r/1340869133.876.10.camel@mopSigned-off-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: Kay Sievers <kay@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull powerpc fixes from Benjamin Herrenschmidt:
 "Here are a few powerpc fixes.  Arguably some of this should have come
  to you earlier but I'm only just catching up after my medical leave.

  Mostly these fixes regressions, a couple are long standing bugs."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/pseries: Fix software invalidate TCE
  powerpc: check_and_cede_processor() never cedes
  powerpc/ftrace: Do not trace restore_interrupts()
  powerpc: Fix Section mismatch warnings in prom_init.c
  ppc64: fix missing to check all bits of _TIF_USER_WORK_MASK in preempt
  powerpc: Fix uninitialised error in numa.c
  powerpc: Fix BPF_JIT code to link with multiple TOCs

Pull x86 fixes from Ingo Molnar.

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, cpufeature: Remove stray %s, add -w to mkcapflags.pl
  x86, cpufeature: Catch duplicate CPU feature strings
  x86, cpufeature: Rename X86_FEATURE_DTS to X86_FEATURE_DTHERM
  x86: Fix kernel-doc warnings
  x86, compat: Use test_thread_flag(TIF_IA32) in compat signal delivery

Pull oprofile fixlet from Ingo Molnar.

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  oprofile: perf: use NR_CPUS instead or nr_cpumask_bits for static array

Pull RCU fix from Ingo Molnar.

Fixes a bug introduced in this merge window by commit b1420f1c ("Make
rcu_barrier() less disruptive")

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rcu: Stop rcu_do_batch() from multiplexing the "count" variable

Continuation lines are buffered internally, intended to merge the
chunked printk()s into a single record, and to isolate potentially
racy continuation users from usual terminated line users.

This though, has the effect that partial lines are not printed to
the console in the moment they are emitted. In case the kernel
crashes in the meantime, the potentially interesting printed
information would never reach the consoles.

Here we share the continuation buffer with the console copy logic,
and partial lines are always immediately flushed to the available
consoles. They are still buffered internally to improve the
readability and integrity of the messages and minimize the amount
of needed record headers to store.
Signed-off-by: NKay Sievers <kay@vrfy.org>
Tested-by: NSteven Rostedt <rostedt@goodmis.org>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The following added support for powernv but broke pseries/BML:
 1f1616e8 powerpc/powernv: Add TCE SW invalidation support

TCE_PCI_SW_INVAL was split into FREE and CREATE flags but the tests in
the pseries code were not updated to reflect this.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
cc: stable@kernel.org [v3.3+]
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit f948501b ("Make hard_irq_disable() actually hard-disable
interrupts") caused check_and_cede_processor to stop working.
->irq_happened will never be zero right after a hard_irq_disable
so the compiler removes the call to cede_processor completely.

The bug was introduced back in the lazy interrupt handling rework
of 3.4 but was hidden until recently because hard_irq_disable did
nothing.

This issue will eventually appear in 3.4 stable since the
hard_irq_disable fix is marked stable, so mark this one for stable
too.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

As I was adding code that affects all archs, I started testing function
tracer against PPC64 and found that it currently locks up with 3.4
kernel. I figured it was due to tracing a function that shouldn't be, so
I went through the following process to bisect to find the culprit:

 cat /debug/tracing/available_filter_functions > t
 num=`wc -l t`
 sed -ne "1,${num}p" t > t1
 let num=num+1
 sed -ne "${num},$p" t > t2
 cat t1 > /debug/tracing/set_ftrace_filter
 echo function /debug/tracing/current_tracer
 <failed? bisect t1, if not bisect t2>

It finally came down to this function: restore_interrupts()

I'm not sure why this locks up the system. It just seems to prevent
scheduling from occurring. Interrupts seem to still work, as I can ping
the box. But all user processes freeze.

When restore_interrupts() is not traced, function tracing works fine.

Cc: stable@kernel.org
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patches tries to fix a couple of Section mismatch warnings like
following one:

WARNING: arch/powerpc/kernel/built-in.o(.text+0x2923c): Section mismatch
in reference from the function .prom_query_opal() to the
function .init.text:.call_prom()
The function .prom_query_opal() references
the function __init .call_prom().
This is often because .prom_query_opal lacks a __init
annotation or the annotation of .call_prom is wrong.
Signed-off-by: NLi Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In entry_64.S version of ret_from_except_lite, you'll notice that
in the !preempt case, after we've checked MSR_PR we test for any
TIF flag in _TIF_USER_WORK_MASK to decide whether to go to do_work
or not. However, in the preempt case, we do a convoluted trick to
test SIGPENDING only if PR was set and always test NEED_RESCHED ...
but we forget to test any other bit of _TIF_USER_WORK_MASK !!! So
that means that with preempt, we completely fail to test for things
like single step, syscall tracing, etc...

This should be fixed as the following path:

 - Test PR. If not set, go to resume_kernel, else continue.

 - If go resume_kernel, to do that original do_work.

 - If else, then always test for _TIF_USER_WORK_MASK to decide to do
that original user_work, else restore directly.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

chroma_defconfig currently gives me this with gcc 4.6:
  arch/powerpc/mm/numa.c:638:13: error: 'dm' may be used uninitialized in this function [-Werror=uninitialized]

It's a bogus warning/error since of_get_drconf_memory() only writes it
anyway.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
cc: <stable@kernel.org> [v3.3+]
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If the kernel is big enough (eg. allyesconfig), the linker may need to
switch TOCs when calling from the BPF JIT code out to the external
helpers (skb_copy_bits() & bpf_internal_load_pointer_neg_helper()).

In order to do that we need to leave space after the bl for the linker
to insert a reload of our TOC pointer.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NMatt Evans <matt@ozlabs.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Pull hwmon changes from Guenter Roeck:
 "Just e-mail address updates"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: Update my e-mail address
  hwmon: (applesmc) correct email address for Jesper Juhl

Pull watchdog fixes from Wim Van Sebroeck:
 "This fixes:
   - the WDIOC_GETSTATUS return value
   - the unregister of all NMI events on exit
   - the loading of the iTCO_wdt driver after the conversion to the
     lpc_ich mfd model."

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: core: fix WDIOC_GETSTATUS return value
  watchdog: hpwdt: Unregister NMI events on exit.
  watchdog: iTCO_wdt: add platform driver module alias

Pull UDF fixes from Jan Kara:
 "Make UDF more robust in presence of corrupted filesystem"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  udf: Fortify loading of sparing table
  udf: Avoid run away loop when partition table length is corrupted
  udf: Use 'ret' instead of abusing 'i' in udf_load_logicalvol()

Pull ubi/ubifs fixes from Artem Bityutskiy:
 "Fix the debugfs regression - we never enable it because incorrect
  'IS_ENABLED()' macro usage: should be 'IS_ENABLED(CONFIG_DEBUG_FS)',
  but we had 'IS_ENABLED(DEBUG_FS)'.  Also fix incorrect assertion."

* tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs:
  UBI: correct usage of IS_ENABLED()
  UBIFS: correct usage of IS_ENABLED()
  UBIFS: fix assertion

In commit 7a879824 we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch is to unregister for NMI events upon exit. Also we are now
making the default setting for allow_kdump enabled.
Signed-off-by: NThomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Pull drm fixes from Dave Airlie:
 "Nearly all intel, one missing license header in nouveau, nothing
  majorly earth shattering."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  Revert "drm/i915: allow PCH PWM override on IVB"
  drm/nouveau: add license header to prime.
  drm/i915: Fix eDP blank screen after S3 resume on HP desktops
  drm/i915: rip out the PM_IIR WARN

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
  sh: Convert sh_clk_mstp32_register to sh_clk_mstp_register
  sh: kfr2r09: fix compile breakage