Even if we only use one gpd, we need alloc 2 gpd and make
the gpd->next pointer to the second gpd, or may get gpd checksum
error, this was checked by hardware
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

use the ios->timing directly is better
It can reflect current timing and do settings by timing
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

cmd_ints_mask and data_ints_mask are constant value,
so make it to const
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add 400Mhz clock source for HS400 mode
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Sometime only need set MMC_CAP_HW_RESET for one of MMC hosts,
So set it in device tree is better.
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable omap_hsmmc for Keystone 2 architecture which reuses the HSMMC
IP found on OMAP platforms.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add ACPI HIDs for Intel host controllers including one
supporting HS400.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add PCI IDs for Intel host controllers
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DesignWare MMC Controller's transfer mode should be decided
at runtime instead of compile-time. So we remove this config
option and read dw_mmc's register to select DMA master.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Acked-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DesignWare MMC Controller's transfer mode should be decided
at runtime instead of compile-time. So we remove this config
option and read dw_mmc's register to select DMA master.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Acked-by: NWei Xu <xuwei5@hisilicon.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DesignWare MMC Controller's transfer mode should be decided
at runtime instead of compile-time. So we remove this config
option and read dw_mmc's register to select DMA master.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Acked-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DesignWare MMC Controller's transfer mode should be decided
at runtime instead of compile-time. So we remove this config
option and read dw_mmc's register to select DMA master.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DesignWare MMC Controller's transfer mode should be decided
at runtime instead of compile-time. So we remove this config
option and read dw_mmc's register to select DMA master.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Acked-by: NGovindraj Raja <govindraj.raja@imgtec.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

synopsys-dw-mshc supports three types of transfer mode. We add
bindings and description for how to use them at runtime.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch add some macros for HCON register operations
to make code more readable.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The eSDHC doesn't have a standard power control register, so when
writing this register in stack we should do nothing to avoid
incorrect operation.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Renesas R8A7794 SoC also has the MMCIF controller.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The "compatible" property text contradicts even the example given in the MMCIF
binding document itself;  moreover, the Renesas MMCIF driver only matches  on
the generic "compatible" string and doesn't look for the SoC specific strings
at all. Thus describe "renesas,sh-mmcif" as a fallback value.

Fixes: b4c27763 ("mmc: sh_mmcif: Document DT bindings")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There's little sense in releasing the host on mmc_add_card() error
immediately after reclaiming  it, so reclaim the host  only in case
of success.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The driver depends on GOLDFISH but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.

That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: NLuis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This allows the tuning code to run and use higher speeds on capable cards.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The drive/sample clocks can be phase shifted.  The drive clock
could be used in a future patch to adjust hold times.  The sample
clock is used for tuning.
Signed-off-by: NAlexandru M Stan <amstan@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This algorithm will try 1 degree increments, since there's no way to tell
what resolution the underlying phase code uses. As an added bonus, doing
many tunings yields better results since some tests are run more than once
(ex: if the underlying driver uses 45 degree increments, the tuning code
will try the same angle more than once).

It will then construct a list of good phase ranges (even ranges that cross
360/0), will pick the biggest range then it will set the sample_clk to the
middle of that range.

We do not touch ciu_drive (and by extension define default-drive-phase).
Drive phase is mostly used to define minimum hold times, while one could
write some code to determine what phase meets the minimum hold time (ex 10
degrees) this will not work with the current clock phase framework (which
floors angles, so we'll get 0 deg, and there's no way to know what
resolution the floors happen at). We assume that the default drive angles
set by the hardware are good enough.

If a device has device specific code (like exynos) then that will still
take precedence, otherwise this new code will execute. If the device wants
to tune, but has no sample_clk defined we'll return EIO with an error
message.
Signed-off-by: NAlexandru M Stan <amstan@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add ciu_drive, ciu_sample clocks and default-sample-phase. This will later
be used by tuning code.

We do not touch ciu_drive (and by extension define default-drive-phase).
Drive phase is mostly used to define minimum hold times, while one could
write some code to determine what phase meets the minimum hold time
(ex 10 degrees) this will not work with the current clock phase framework
(which floors angles, so we'll get 0 deg, and there's no way to know what
resolution the floors happen at). We assume that the default drive angles
set by the hardware are good enough.
Signed-off-by: NAlexandru M Stan <amstan@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We've introduced a new helper in the MMC core:
mmc_regulator_set_vqmmc().  Let's use this in dw_mmc.  Using this new
helper has some advantages:

1. We get the mmc_regulator_set_vqmmc() behavior of trying to match
   VQMMC and VMMC when the signal voltage is 3.3V.  This ensures max
   compatibility.

2. We get rid of a few more warnings when probing unsupported
   voltages.

3. We get rid of some non-dw_mmc specific code in dw_mmc.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This adds logic to the MMC core to set VQMMC.  This is expected to be
called by MMC drivers like dw_mmc as part of (or instead of) their
start_signal_voltage_switch() callback.

A few notes:

* When setting the signal voltage to 3.3V we do our best to make VQMMC
  and VMMC match.  It's been reported that this makes some old cards
  happy since they were tested back in the day before UHS when VQMMC
  and VMMC were provided by the same regulator.  A nice side effect of
  this is that we don't end up on the hairy edge of VQMMC (2.7V),
  which some EEs claim is a little too close to the minimum for
  comfort.
  This is done in two steps. At first we try to find a VQMMC within
  a 0.3V tolerance of VMMC and if this is not supported by the
  supplying regulator we try to find a suitable voltage within the
  whole 2.7V-3.6V area of the spec.

* The two step approach is currently necessary, as the used
  regulator_set_voltage_triplet(min, target, max) uses a simple
  implementation that just tries two basic steps:
	regulator_set_voltage(target, max);
	regulator_set_voltage(min, target);
  So with only one step with 2.7-3.6V borders, if a suitable voltage
  is a bit below VMMC, we would directly get the lowest 2.7V
  which some boards (like Rockchips) don't like at all.

* When setting the signal voltage to 1.8V or 1.2V we aim for that
  specific voltage instead of picking the lowest one in the range.

* We very purposely don't print errors in mmc_regulator_set_vqmmc().
  There are cases where the MMC core will try several different
  voltages and we don't want to pollute the logs.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We will shortly need the calculation of an ocr-bit to the actual
voltage in a second place too, so move it from mmc_regulator_set_ocr
to a common function mmc_ocrbitnum_to_vdd to make that possible.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.

Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.

To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Freescale eSDHC driver now supports both little-endian and
big-endian mode eSDHC IPs for ARM and PPC. So, MMC_SDHCI_OF_ESDHC
option needs to be reconfigured.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To support little endian eSDHC controller, we redefine both BE and
LE IO accessors. In the new accessors, use ioread*/iowrite* instead
of in_be32/out_be32 and will select accessors according to endian
mode in probe function.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add another PCI ID for an Intel eMMC host controller.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let's use DIV_ROUND_CLOSEST for rounding, not just truncating
division.  This lets us get closer to the right rate.

Before this:
  set_phase(86) delay_nums=26 reg[0xf000420c]=0x468 actual_degrees=83
  set_phase(89) delay_nums=27 reg[0xf000420c]=0x46c actual_degrees=86

After this:
  set_phase(86) delay_nums=27 reg[0xf000420c]=0x46c actual_degrees=86
  set_phase(89) delay_nums=28 reg[0xf000420c]=0x470 actual_degrees=90
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Because of the inexact nature of the extra MMC delay elements (it's
not possible to keep the phase monotonic and to also make phases (mod
90) > 70), we previously only allowed phases (mod 90) of 22.5, 45,
and 67.5.

But it's not the end of the world if the MMC clock phase goes
non-monotonic.  At most we'll be 25 degrees off.  It's way better to
test more phases to look for bad ones than to be 25 degrees off, because
in the case of MMC really the point is to find bad phases and get as far
asway from the as possible.  If we get to test extra phases by going
slightly non-monotonic then that might be fine.  Worst case we would
end up at a phases that's slight differnt than the one we wanted, but
at least we'd still be quite far away from the a bad phase.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Fold in more precise variance-values of 44-77 instead of 40-80.
Fold in the actual removal of the monotonic requirement and adapt
patch message accordingly.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

drivers/mmc/host/sdhci-pci-core.c:447:1-4: WARNING: end returns can be simpified

 Simplify a trivial if-return sequence.  Possibly combine with a
 preceding function call.

Generated by: scripts/coccinelle/misc/simple_return.cocci

CC: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It has no external callers.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sdhci-pci-o2micro.c contains no initialisation and its functions are only
called from shdci-pci.c, so there is no reason for it to be a separate
module, let alone or for it to always be built-in.

- Rename sdhci-pci.c to sdhci-pci-core.c so that the sdhci-pci module
  can be built from multiple source files
- Add sdhci-pci-o2micro.c to it
- Remove redundant exports
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

According to hardware spec, validate DDR50 mode
for SDXC.
Signed-off-by: NWeijun Yang <york.yang@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>